Adastra RM4460 Manual de Usario

Adastra receptor RM4460

Lee a continuación 📖 el manual en español para Adastra RM4460 (6 páginas) en la categoría receptor. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/6
RM4460
4-INPUT, 4-ZONE MIXER- PLIFIER 4 x 60W AM
Item ref: 953.446UK
User Manual
Version 0 1.
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
953.446 User Manual UK
Introduction
Thank you for choosing an Adastra 4-zone mixer-amp as part of your sound system. RM4460
This mixer with 4 separate 100V amplifiers has the advantage of a 4 in / 4 out matrix with inbuilt media player.
Please read this manual to gain the best results from your product and avoid damage through misuse.
SAFETY SYMBOL AND MESSAGE CONVENTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this
unit
This symbol indicates that there are important operating and maintenance instructions in the
literature accompanying this unit.
SAFETY NOTICE
1. Prior to use, read through this manual
2. Keep the manual in good condition
3. Pay attention to safety warnings
4. Observe all operating requirements
5. Do not use the device near water or wet areas
6. For cleaning, only use a lint-free, dry cloth
7. Install according to the specifications
8. Place away from heat sources or heating appliances
9. Use mains lead provided and avoid damage to cable or connectors
10. Unplug power from mains during stormy weather or if unused for long periods
11. In case of malfunction, water ingress or other damage, consult qualified service personnel
12. Do not place in damp areas or near liquids or moisture. Do not spill liquids on the housing
13. Please pay attention to warning symbols during transit and placement
14. Terminals marked with the symbol are HAZARDOUS LIVE and should only be connected by qualified personnel
15. Ensure that the apparatus is connected to a mains socket with a protective EARTH connection
16. Ensure correct operation of the mains switch
Warning
To prevent the risk of fire or electric shock, do not expose any components to rain or moisture.
If liquids are spilled on the casing, stop using immediately, allow unit to dry out and have checked by qualified personnel before
further use.
Avoid impact, extreme pressure or heavy vibration to the case
No user serviceable parts inside Do not open the case refer all servicing to qualified service personnel. – –
Safety
• Check for correct mains voltage and condition of IEC lead before connecting to power outlet
Placement
• This unit can be used free-standing or fixed into a 19” rack
• Ensure adequate support and access to controls and connectors when rack-mounting
Cleaning
• Use a soft cloth with a neutral detergent to clean the housing as required
• Do not use strong solvents for cleaning the unit
953.446 User Manual UK
Front panel
Rear panel
Setting up
The may be operated free-standing or mounted into a 19 rack. Ensure adequat ventilation and access to connectors and RM4460 ”e
controls. Start with all LEVEL controls turned lly down and BASS/TREBLE EQ controls set mid- y (12 o clock), then proceed to fu wa ’
connect all required input sources.
I the optional CS4 call station is being used, connect this via the RJ45 connector on the rear panel (36) f
Input 1 accepts a paging microphone on balanced XLR (34) and a VOX feature may be ed to give this priority over other channels. us
To enable VOX, set the VOX DIP switch to ON (33), which will cause other channels to mute when the microphone is spoken into.
Next to the VOX DIP switch is a PHANTOM DIP switch (34) which activates phantom power to the R connector for condenser mics. XL
Inputs 2 and 3 can accept a microphone or line input o a combo connector, which accepts either 6.3mm jack or XLR (30, 32) n
A DIP switch (29, 31) gives the option of selecting mic or line level sensitivity for the input.
An adjacent DIP switch can enable phantom power to the XLR contacts of the combo connector to power a condenser microphone.
The LINE input can be connected via a pair of RCA connectors (27) or a 3-screw terminal connector.
Th screw terminal ock is removable for easy connection and has terminals for +/- (28) e bl /G
Connect the hot signal to + cold signal to and ground to G for a balanced input signal. “ ” “ ”, “ ” “–” “ ”
Unbalanced signals only use 2 wires, so connect the signal (core) + and connect the ground (braid) to - and G together. to “ ” “ ”
A separate 3.5mm line input on the front panel can be fed through the media player for an mp3 player or smart pho . ne
Line level outputs from each zone may be connected from RCA connectors (26) for sending further amplifiers if required. to
1.
AUX 3.5mm jack input
11.
Input 2 EQ controls
2.
USB port (for pen drive only)
12.
Input 2 level control & signal LED
3.
Media player controls
13.
Input 2 zone output selectors
4.
Media player display
14.
Input 3 EQ controls
5.
Media/Line input selector
15.
Input 3 level control & signal LED
6.
Media/Line level control & signal LED
16.
Input 3 zone output selectors
7.
Media/Line zone output selectors
17.
Zone level & signal/clip & mute/call LEDs 1
8.
Input 1 p ing mic EQ controls ag
18.
Zone 2 level & signal/clip & mute/call LEDs
9.
Input 1 p ing mic level control & signal LED ag
19.
Zone 3 level & signal/clip & mute/call LEDs
10.
Input 1 p ing mic zone output selectors ag
20.
Zone 4 level & signal/clip & mute/call LEDs
21.
Power on/off switch & LED
22.
IEC mains inlet & fuse holder
31.
Input 2 Phantom/Mic/Line DIP switches
23.
Cooling fan vent (do not cover)
32.
Input 2 combo jack/XLR connector
24.
Low impedance (4 speaker tput terminals Ω) ou
33.
Input 1 Phantom/Mic/Line DIP switches
25.
100V speaker tput terminals ou
34.
Input 1 combo jack/XLR connector
26.
Individual zone line level signal outputs (RCA)
35.
Call station level control (for optional CS4)
27.
Line input (2 x RCA)
36.
Call statio RJ45 input (for optional CS4) n
28.
Line input ( - round screw termina ) +/ /G ls
37.
24V emergency mut screw terminals e
29.
Input 3 Phantom/Mic/Line DIP switches
38.
Bluetooth antenna connection (SMA)
30.
Input 3 combo jack/XLR connector
39.
FM radio aerial F-connector

Especificaciones del producto

Marca: Adastra
Categoría: receptor
Modelo: RM4460

¿Necesitas ayuda?

Si necesitas ayuda con Adastra RM4460 haz una pregunta a continuación y otros usuarios te responderán


receptor Adastra Manuales

Adastra

Adastra V-122 Manual de Usario

13 Septiembre 2024
Adastra

Adastra STA40-WIFI Manual de Usario

22 Agosto 2024
Adastra

Adastra UM30 Manual de Usario

21 Agosto 2024
Adastra

Adastra US90 Manual de Usario

21 Agosto 2024
Adastra

Adastra IWA230B Manual de Usario

21 Agosto 2024
Adastra

Adastra RM4460 Manual de Usario

19 Agosto 2024
Adastra

Adastra RM360D Manual de Usario

19 Agosto 2024

receptor Manuales

Últimos receptor Manuales

Crown

Crown CDi DriveCore 2|300BL Manual de Usario

27 Octubre 2024
Boss

Boss PT3000 Manual de Usario

27 Octubre 2024
Speco Technologies

Speco Technologies PBM120AT Manual de Usario

27 Octubre 2024
Fosi Audio

Fosi Audio V3 Manual de Usario

26 Octubre 2024
Jensen

Jensen CAR710-4BC Manual de Usario

25 Octubre 2024
Onkyo

Onkyo TX-RZ830 Manual de Usario

24 Octubre 2024
Pioneer

Pioneer VSX-1122K Manual de Usario

22 Octubre 2024
Yamaha

Yamaha HTR-5072 Manual de Usario

21 Octubre 2024
NAD

NAD C 355BEE Manual de Usario

20 Octubre 2024
Yamaha

Yamaha RX-A810 Manual de Usario

20 Octubre 2024