Amana PWHK01C Manual de Usario

Amana horno PWHK01C

Lee a continuación 📖 el manual en español para Amana PWHK01C (3 páginas) en la categoría horno. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/3
Description
The PTAC Wire Harness kit provides connection from the 14-pin or 18-pin terminal strip on the PTAC control board to the
following board features:
Door Switch*
Motion Sensor*
Emergency Hydronic Heat**
Load Shedding**
Front Desk Control**
Transfer Fan (relay must be manufacturer-approved and have a DC low voltage coil)
Remote Thermostat (must be manufacturer-approved)
The kit includes a 14-pin and an 18-pin female housing with 18 jumper wires and wire nuts. The installation and servicing of
this equipment should be performed by qualified, experienced technicians.
*Contact your sales person for proper manufacturer-approved devices and wiring instructions.
**If other than a “dry switch” is used in connecting these features, consult manufacturer before proceeding.
FD1 (ORANGE)
FD2 (ORANGE)
C (BLACK)
R (RED)
GL (GREEN)
Y (YELLOW)
B (BLUE)
EH (WHITE W/
STRIPES)
IN (RED W/
STRIPES)
LS (YELLOW W/
STRIPES)
GH (GREEN W/
STRIPES)
TF(-) (GRAY W/
STRIPES)
TF(+) (GRAY)
W2 (WHITE)
MS1 (VIOLET)
MS2 (VIOLET)
DS1 (BROWN)
DS2 (BROWN)
PTAC
WIRE HARNESS KIT
(PWHK01C)
INSTALLATION INSTRUCTIONS
Due to policy of continual product
improvement, the right is reserved to
change specifications and design
without notice.
July 2004
Part No.20319103
Printed in U.S.A.
2
WARNING
DISCONNECT ELECTRICAL POWER SOURCE BEFORE WIRING THE UNIT.
FAILURE TO DO SO MAY RESULT IN INJURY OR DEATH FROM ELECTRICAL
SHOCK. THE UNIT "OFF" SWITCH DOES NOT DISCONNECT ALL POWER TO
THE UNIT.
INSTALLATION
WARNING
ALL WIRING MUST COMPLY WITH APPLICABLE LOCAL AND NATIONAL CODES.
TYPE AND LOCATION OF FUSED DISCONNECT SWITCH(ES) MUST COMPLY
WITH ALL APPLICABLE CODES.
1. Disconnect power and remove the front panel per unit
installation instructions.
2. Remove 14-pin (or 18-pin, if applicable) female housing
from control board.**
Using the following table and either Figure 1 or 2 as
guides, (Figure 1 for boards with knobs; Figure 2 for
boards with touchpads) choose the feature desired and
insert the proper jumper wire into the appropriate slot on
the housing. Ensure the jumper wires are oriented as
shown in Figure 3.
Re-install the 14-pin or 18-pin housing. Ensure housing
faces the direction shown in either Figure 1 or 2. Take
EH
IN
LS
FD1
FD2
TF(-)
TF(+)
C
R
GL
W2
Y/W1
B
GH
Figure 1: Control Knobs (14-pin Units)
Fea ture Pins Used
Emergency Hydronic Heat EH, IN
Load Shedding LS, IN
Front Desk Control FD1, FD2
Transfer Fan TF(-), TF (+)
Remote Thermostat C, R, GL, W 2, Y/W 1, B, GH
Motion Sensor* MS1, MS2
Door Switch* DS1, DS2
Table 1
*These features and connections are only available on touchpad control 18-pin units.
**If a female housing is not present on the control board, use the housing supplied with this kit.
DS1 DS2 MS1 MS2 EH IN LS FD1 FD2 TF- TF+ C R GL W2 Y/W1 B GH
Figure 2: Touchpad (18- Pin Units)
care to ensure the plastic housing and metal pins are
aligned correctly; otherwise, the unit will not funciton
properly.
NOTE: Only load wires intended for installation. Extra
wires can be used to connect other PTAC boards. One
PWHK01C kit can be used for multiple boards.
3. Connect the kit wiring to the field wiring using the wire
nuts provided. Route the kit wiring as shown in Figure 4.
Do not run wires through basepan or wall sleeve.
4. With the unit in the OFF position, reconnect the power
and ensure the master switch is in the ON position.
5. Reinstall the front cover per unit installation instructions.
Check the unit for proper operation.
Figure 3
14-PIN 18-PIN
3
Figure 4
Route low voltage wire as
shown above. No holes
are permitted in chassis
basepan or wallsleeve
when routing low voltage
wire.
123
ON
Route low voltage wire as
shown above. No holes
are permitted in chassis
basepan or wallsleeve
when routing low voltage
wire.

Especificaciones del producto

Marca: Amana
Categoría: horno
Modelo: PWHK01C

¿Necesitas ayuda?

Si necesitas ayuda con Amana PWHK01C haz una pregunta a continuación y otros usuarios te responderán


horno Amana Manuales

Amana

Amana AGR5844 Manual de Usario

20 Octubre 2024
Amana

Amana AER5830 Manual de Usario

20 Octubre 2024
Amana

Amana AGR4203MNB Manual de Usario

15 Septiembre 2024
Amana

Amana AER5735QAS Manual de Usario

3 Septiembre 2024
Amana

Amana AER5511ACW Manual de Usario

1 Septiembre 2024
Amana

Amana AOES3030E Manual de Usario

30 Agosto 2024
Amana

Amana ACR4503SFB Manual de Usario

29 Agosto 2024
Amana

Amana AER5845RAW0 Manual de Usario

28 Agosto 2024
Amana

Amana AWO6317SFS Manual de Usario

28 Agosto 2024
Amana

Amana ACR2303MFW Manual de Usario

28 Agosto 2024

horno Manuales

Últimos horno Manuales

Continental Edison

Continental Edison CECM6065W Manual de Usario

27 Octubre 2024
Taurus

Taurus HM778WHD Manual de Usario

27 Octubre 2024
Lacanche

Lacanche CITEAUX Manual de Usario

27 Octubre 2024
JennAir

JennAir JDS1450FS Manual de Usario

27 Octubre 2024
Orima

Orima ORP-76-IN Manual de Usario

27 Octubre 2024
Breville

Breville the Handy Hot Plate BHP150 Manual de Usario

27 Octubre 2024
JennAir

JennAir JGRP436HL Manual de Usario

27 Octubre 2024
Neff

Neff C17MS22G1 Manual de Usario

27 Octubre 2024
Pit Boss

Pit Boss BK24 Manual de Usario

27 Octubre 2024
Guzzanti

Guzzanti GZ-8206 Manual de Usario

27 Octubre 2024