AMX Inspired XPress IS-SPX-1300K Manual de Usario

AMX No categorizado Inspired XPress IS-SPX-1300K

Lee a continuación 📖 el manual en español para AMX Inspired XPress IS-SPX-1300K (2 páginas) en la categoría No categorizado. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Installation Guide

NXD-430 4.3" Modero® Wall/Flush Mount Touch Panel

For more detailed installation, configuration, programming, file transfer, and operating

instructions, refer to the NXD-430/435 Operation/Reference Guide, available online at

www.amx.com.

Overview

The NXD-430 Modero ® Wall/Flush Mount Touch Panel includes a mini-USB port for

programming and one NetLinx-programmable button. All power is supplied via Power

Over Ethernet (PoE), utilizing a PS-POE-AF PoE Injector (FG423-80) or equivalent

PoE device.The NXD-430 comes in black (FG2262-01) and white (FG2262-02).

Specifications

Panel Connectors and Wiring

FIG. 2 shows the connectors located on the NXD-430 Modero panel. The mini-USB

port is used for programming the touch panel.

For more information on connection and use of the Panel Connectors, as well as

information on programming, please refer to the NXD-430/435 Operation/Reference

Guide, available at www.amx.com.

Capacitive Touch Button

The NXD-430 has one main button on the front of the device, in the center of the

bezel. This button has several uses:

• Press the button once to start a previously programmed function, or to turn off

the display if not previously programmed.

• Press and hold the button for 6 seconds to put the device into Setup Mode.

• Press and hold the button for 9 seconds to enter Calibration Mode.

• Press and hold the button for 20 seconds to reboot the panel.

The front button of the NXD-430 utilizes capacitive touch, which detects the electrical

conductivity of human skin and reacts directly to touch. This allows the button to resist

wear and dirt, as the button does not have any actual physical button to depress.

NXD-430 Setup and System Connection

1. Carefully remove the panel from the shipping box, peel the protective plastic

cover from the LCD, and apply power to the panel via the PoE Injector.

2. From below the LCD, press the front button for 9 seconds (passing over the

Setup page) to access the Calibration setup page and follow the on-screen

instructions to return to the main Setup page.

3. Press the on-screen Protected Setup button on the Setup page.

4. Enter the panel password into the on-screen keypad (default is 1988).

5. Press the Device Number field to open the on-screen Device Number keypad

and enter a value for the panel (default is 32001).

6. Press the System Settings button to open the System Settings page.

7. From the IP tab, toggle the DHCP Static field to DHCP if it is not already set to

DHCP.

8. From the tab, toggle the Master Type field to Ethernet.

• Toggle the Mode field to URL.

• Enter both the System Number and IP Address of the target Master.

9. Enter a valid Username and Password if the target Master is secured.

10. Press the Back button and then press the on-screen Reboot button to save any

changes and cycle power to the panel.

FIG. 1 NXD-430 4.3" Modero Wall/Flush Mount Touch Panel - White

NXD-430 (FG2262-01/02) Specifications

Dimensions (HWD): • NXD-430: 4.13" x 5.5” x 2.13" (10.48 cm x 13.97 cm x 5.40 cm)

• CB-TP5 Rough-In/Wallbox (optional): 4.27" x 5.14" x 3.40" 

(10.86 cm x 13.06 cm x 8.64 cm)

Weight: • 0.65 lbs (0.29 kg)

Power 

Requirements:

• PoE Powered - No local Power Supply needed

• Max power draw: 5.5W.

Memory (Factory

default):

• 128 MB SDRAM

• 256 MB integrated Flash Memory (not upgradeable - factory

programmed)

Certifications: • FCC Part 15 Class B

• CE

• IEC 60950

• RoHS

Panel LCD 

Parameters:

• Aspect ratio: 16 x 9

• Minimum brightness (luminance): 280 cd/m2

• Channel transparency: 8-bit Alpha blending

• Contrast ratio: 250:1

• Display colors: 256 thousand colors (18-bit color depth)

• Dot/pixel pitch: 0.14 mm

• Panel type: WQVGA

• Screen resolution: 480 x 272 pixels (HV) @ 60 Hz frame

frequency

• Viewing dimensions: 2 3/16" x 3 13/16" (5.56 cm x 9.68 cm)

Active Screen Area: • 2 1/8" x 3 3/4" (5.40 cm x 9.53 cm)

Viewing Angles: • Left/Right/Up/Down: 80/80/60/80

Front Panel 

Components:

•Center Button: Capacitive touch button provides both access to

the Setup and Calibration pages and toggles the panel between

a "sleep" or "wake" state. This button is also user-

programmable.

Side Panel 

Connectors:

• Ethernet 10/100 Port:: RJ-45 port for 10/100 Mbps

communication. The Ethernet port automatically negotiates the

connection speed (10 Mbps or 100 Mbps), and whether to use

half duplex or full duplex mode. Power is supplied through

Power Over Internet (PoE). NXD-430 panels communicate with

the NetLinx Master using the ICSP protocol over Ethernet. LEDs

show communication activity, connections, speeds, and mode

information:

L/A-link/activity - Yellow LED lights On when the Ethernet cables

are connected and terminated correctly and then blinks when

receiving Ethernet data packets.

SPD-speed - Green LED lights On when the connection speed is

100 Mbps and turns Off when the speed is 10 Mbps.

• Mini-USB Connector: 5-pin Mini-USB connector used for

programming, firmware update, and touch panel file transfer

between the PC and the target panel.

Capacitive Touch Center Button

Touch screen

NXD-430 Specifications (Cont.)

Operating /Storage

Environments:

• Operating Temperature: 0° C (32° F) to 40° C (104° F)

• Operating Humidity: 5% - 85% relative humidity

(non-condensing)

• Storage Temperature: -20° C (-4° F) to 60° C (140° F)

• Storage Humidity: 5% - 85% RH

Included 

Accessories:

• NXD-430 Installation Guide (93-2262-01)

Other AMX 

Equipment:

• CB-TP5i Rough-In/Wallbox (FG038-11)

• Back Cover for the CB-TP5i Rough-In/Wallbox (FG038-12)

• PS-POE-AF PoE Injector (FG423-80)

• NXA-BEZP-430-BK Black Portrait Bezel Kit for the NXD-430

( )FG2262-10

• NXA-BEZP-430-WH White Portrait Bezel Kit for the NXD-430

(FG2262-11)

• CC-USB Type-A to Mini-B 5-wire programming cable 

( )FG10-5965

• NXA-RK5 Rack Mount Kit for 5" Wall Mount panels (FG2904-55):

- 5" Rackmount 

- Four Screws, #10-32 x.625, PH Truss, BLK 

- Four Washers, #10, Black Nylon

- Three Screws, #4-40 x.250, PPH, BLK

FIG. 2 Connector layout on the NXD-430 Modero Wall/Flush Touch Panel

Ethernet 10/100 port

Mini-USB port

Back box

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

11/11

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-2262-01 REV: D

Installation of the NXD-430

While the NXD-430 is designed to fit into pre-existing NXD-CV5 touch panel sites,

the actual installation differs from that of the NXD-CV5 in several significant ways.

The NXD-430 can be installed either directly into the (optional) CB-TP5I Rough-In

Box or another solid surface environment, using either solid surface screws or the

included locking tabs for different mounting options. For more information, please

refer to the NXD-430/435 Operation/Reference Guide, available at www.amx.com.

The NXD-430 is contained within a clear outer housing known as the back box

(FIG. 3). This back box is not removed when installing the device into a wall or into a

Rough-In Box.

Installing the NXD-430 into a wall

Unlike most AMX touchpanels, the NXD-430 comes with a clear plastic backbox

(FIG. 7) designed to attach the panel to most standard wall materials. This backbox

has a locking tab on three of the four faces (missing only on the face containing the

space for the connections) to help lock the backbox to the wall. These locking tabs

are only extended AFTER the backbox is inserted into the wall.

WARNING: When installing the backbox, make sure that the assembly is in the

correct position and in the correct place. Once the locking tabs are extended and

locked into place, removing the backbox may be difficult without having access to the

back of the wall or causing damage to the wall.

Note: In order to guarantee a stable installation of the NXD-430, the thickness of the

wall material must be a minimum of .50 inches (1.27cm) and a maximum of .875

inches (2.22cm).

WARNING: The maximum recommended torque to screw in the locking tabs on the

plastic back box is 5 IN-LB [56 N-CM]. Applying excessive torque while tightening the

tab screws, such as with powered screwdrivers, can strip out the locking tabs or

damage the plastic back box.

1. Prepare the area by removing any screws or nails from the drywall before

beginning the cutout process.

2. Cut out the surface for the back box. Refer to the dimensions in the NXD-430/

435 Operation/Reference Guide, available from www.amx.com, for more 

information.

CAUTION: Making sure that the actual cutout opening be slightly smaller than the

provided dimensions is highly recommended. This action provides the installer with a

margin for error if the opening needs to be expanded. Too little wall material removed

is always better than too much.

3. Remove the faceplate from the NXD-430.

4. Disconnect the capacitive touch connector from the 10-pin plug on the 

faceplate.

5. Insert both connectors into their corresponding locations along the left side of

the NXD-430 touch panel.

6. Test the incoming wiring by attaching the panel connections to their terminal

locations and applying power via the PoE Injector. Verify that the panel is

receiving power and functioning properly to prevent repetition of the

installation.

7. Thread the incoming Ethernet and mini-USB wiring (if mini-USB access is

desired) from their terminal locations through the surface opening. Leave

enough slack in the wiring to accommodate any re-positioning of the panel.

8. Push the back box into the wall opening. Insure that the locking tabs lie flush

against the back box.

9. Extend the locking tabs on the sides of the back box by tightening the screws

inside the box until snug. Not all of the tabs must be extended to lock the back

box in place, but extending a minimum of the top and bottom tabs is highly

recommended. Apply enough pressure to the screw head to keep the box flush

with the wall: this ensures that the locking tabs will tighten up against the inside

of the wall. 

The back box is clear to allow visual confirmation that the tabs have been

extended and are gripping the wall, as well as in assisting with removal if

necessary.

NOTE: Do not disconnect the connectors from the touch panel. The unit must be

installed with the attached connectors before being inserted into the drywall.

10. Carefully replace the two Plastite screws holding the device to the back box.

11. Reconnect the capacitive touch connector to the 10-pin plug on the faceplate.

12. Place the faceplate back onto the device.

13. Reconnect the terminal Ethernet and USB to their respective locations on

either the Ethernet port or NetLinx Master.

Installing the NXD-430 into a Flat Surface using #4 screws

Three #4 mounting screws (not included) are secured through circular holes located

at the left and right sides of the NXD-430. The most important thing to remember

when mounting the NXD-430 is that the outer frame (Mounting Tabs) must be

installed flush against the mounting surface.

• Refer to SP-2262-02 for detailed installation dimensions.

• Cutting out the surface slightly smaller than what is outlined in the installation

drawings in order to make any necessary cutout adjustments, is highly

recommended.

1. Prepare the area by removing any screws or nails from the surface before

beginning the cutout process.

2. Cut out the surface for the NXD-430.

3. Remove the faceplate from the NXD-430.

4. Disconnect the capacitive touch connector from the 10-pin plug on the 

faceplate.

5. Thread the incoming Ethernet and USB wiring from their terminal sources

through the surface opening. Leave enough slack in the wiring to

accommodate any re-positioning of the panel.

6. Connect the Ethernet and USB connectors to their corresponding locations

along the left side of the un-powered NXD-430 touch panel. The USB

connectors can be from either a USB extension cable or a wireless USB RF

transmitter.

NOTE: Do not disconnect the connectors from the touch panel. The unit must be

installed with the necessary connectors before being inserted into the solid surface.

7. Carefully slide the main unit into the cutout until the Mounting Tabs of the

NXD-430 lie flush against the wall.

8. Insert and secure three #4 Mounting Screws (not included) into the

corresponding holes located along the sides of the NXD-430, using a grounded

Phillips-head screwdriver, until the unit is secure and flush against the wall.

9. Reconnect the capacitive touch connector to the 10-pin plug on the faceplate.

10. Place the faceplate back onto the device.

11. Reconnect the terminal Ethernet and USB to their respective locations on

either the Ethernet port or NetLinx Master.

FIG. 3 NXD-430 backbox with closed and open locking tabs

Locking tabs - Closed Locking tabs - Open

Locking tab screws

Especificaciones del producto

Marca:	AMX
Categoría:	No categorizado
Modelo:	Inspired XPress IS-SPX-1300K

¿Necesitas ayuda?

Si necesitas ayuda con AMX Inspired XPress IS-SPX-1300K haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado AMX Manuales

AMX HPX-MSP-7-SL Manual de Usario

18 Septiembre 2024

AMX HPX-MSP-10-SL Manual de Usario

18 Septiembre 2024

AMX TPC-WIN8-TAB Manual de Usario

17 Septiembre 2024

AMX NMX-DEC-N1222A Manual de Usario

16 Septiembre 2024

AMX NMX-DEC-N2222A Manual de Usario

16 Septiembre 2024

AMX NMX-DEC-N1233 Manual de Usario

16 Septiembre 2024

AMX NMX-DEC-N2211 Manual de Usario

16 Septiembre 2024

AMX NMX-ENC-N1134A Manual de Usario

16 Septiembre 2024

AMX NMX-ENC-N1133 Manual de Usario

16 Septiembre 2024

AMX NMX-ENC-N2315-WP Manual de Usario

16 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024