AMX MXD-700-NC Manual de Usario

AMX No categorizado MXD-700-NC

Lee a continuación 📖 el manual en español para AMX MXD-700-NC (2 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

QUICK START GUIDE

MXD-700 7" Modero X® Series Wall Mount Touch Panel

Overview

The MXD-700 7" Modero X Series ® Wall Mount Touch Panel features edge-to-edge capacitive

touch glass with multi-touch capabilities as well as advanced technology empowering users to

operate AV equipment seamlessly, while providing the ultimate in audio and video quality. The

MXD-700 is available in Portrait and Landscape layouts:

Product Specifications

For a full listing of product specifications, refer to the X-Series Touch Panels MXD/T-1000,

MXD/T-700 & MXD-430 Instruction Manual (available to view/download from www.amx.com).

Note: The MXD-700-P-NC (FG5968-28) and MXD-700-L-NC (FG5968-29) No Comm touch

panels do not have microphone capability. These otherwise have all of the functionality of the

MXD-700 panels.

MXD-700 Installation

• For more detailed installation instructions including important notes on thermal

concerns with Rack and Wall installations, refer to the X-Series Touch Panels MXD/

T-1000, MXD/T-700 & MXD-430 Instruction Manual (available to view/download from

www.amx.com).

• Detailed specifications drawings for the MXD-700 are available to download from

www.amx.com.

The MXD-700 may be installed directly into a solid surface environment, using either solid

surface screws or the included locking tabs for different mounting options.

Once installed, the MXD-700 is contained within a clear outer housing known as the Backbox

(FIG. 2). The Backbox is removed to install it into a wall, or when using the optional Rough-In

Box accessory (FG039-18).

Note: For typical mounting surfaces, such as drywall, use the locking tabs as the primary

method for securing the Backbox to the surface. For thin walls or solid surfaces, use mounting

screws (not included).

Power Via PoE

Power for the MXD-700 is supplied via PoE (Power Over Ethernet), utilizing an AMX-certified,

capacitive touch-compliant PoE injector or other approved AMX PoE power source. The

incoming Ethernet cable should be connected to the RJ45 port on the MXD-700.

Installing the MXD-700 Into a Wall

The MXD-700 comes with a clear plastic Backbox (designed to attach the panel to most

standard wall materials. This Backbox has two locking tabs (one on top and one on bottom) to

help lock the Backbox to the wall. These locking tabs are only extended AFTER the Backbox is

inserted into the wall (FIG. 3).

• When installing the Backbox, make sure that the assembly is in the correct position and

in the correct place. Once the locking tabs are extended and locked into place, removing

the Backbox may be difficult without having access to the back of the wall or causing

damage to the wall.

• In order to ensure a stable installation of the MXD-700, the thickness of the wall

material must be a minimum of .50 inches (1.27cm) and a maximum of .875 inches

(2.22cm). The mounting surface should also be smooth and flat.

Installing the Backbox

For best results, use the included Installation Template (68-5968-04) to ensure proper

placement. The template is marked on one side with directions for both landscape and portrait

installations to ensure that the touch panel and Backbox are properly aligned.

WARNING: Using the Installation Template to select the final placement of the Backbox is highly

recommended. The outside edges of the template are the same dimensions as the touch panel,

which allows you to troubleshoot possible conflicts with wall edges, doors, and other potential

obstacles.

1. Prepare the area by removing any screws or nails from the drywall before beginning the

cutout process.

2. After ensuring proper placement, cut out the mounting surface for the Backbox, using

the (included) Installation Template as a guide.

CAUTION: Making sure the actual cutout opening is slightly smaller than the provided

dimensions is highly recommended. This provides a margin of error if the opening needs to

be expanded. Too little wall material removed is always better than too much.

3. Thread the incoming Ethernet cable through the surface opening (FIG. 4).

Leave enough slack in the wiring to accommodate any re-positioning of the panel.

4. Remove the Backbox knockouts and thread the incoming wiring through the knockout

holes.

5. Thread the incoming cables from the mounting surface opening and through the

knockouts.

6. Push the Backbox into the mounting surface. Insure that the locking tabs lie flush

against the Backbox and that the Backbox goes freely into the opening.

7. Extend the locking tabs on the sides of the Backbox by tightening the screws inside the

box until snug. Apply enough pressure to the screw head to keep the box flush with the

wall: this ensures that the locking tabs will tighten up against the inside of the wall. The

Backbox is clear to allow visual confirmation that the tabs have been extended and are

gripping the wall, as well as in assisting with removal if necessary.

Note: The maximum recommended torque to screw in the locking tabs on the Backbox is 5

IN-LB [56 N-CM]. Applying excessive torque while tightening the tab screws, such as with

powered screwdrivers, can strip out the locking tabs or damage the Backbox.

8. For additional strength, #4 mounting screws (not included) may be secured via

mounting holes located at the left and right sides of the MXD-700 (FIG. 4). In order to

prevent damage to the touch panel, make sure that these are flush with the Backbox.

Portrait MXD-700-P FG5968-08

Landscape MXD-700-L FG5968-14

FIG. 1 MXD-700-P/L WALL MOUNT (PORTRAIT AND LANDSCAPE)

MXD-700 SPECIF ICATIONS

Dimensions (HWD) • Landscape: 4 13/16" x 7 5/16" x 2 1/2" (122mm x 186mm x 63mm)

• Portrait: 7 5/16" x 4 13/16" x 2 1/2" (186mm x 122mm x 63mm)

Weight 1.4 lbs (0.64 Kg)

Power Consumption • Full-On: 8W

• Standby: 3.2W

• Shutdown: 1W

• Start-Up Inrush Current: Not applicable due to PoE standard

External Power

Supply Required

Optimal performance requires use of one of the following AMX PoE power

supplies (not included):

• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)

• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)

Certifications • UL 60950-1

• FCC Part 15 Class B

• C-Tick CISPR 22 Class B

• CE EN 55022, EN 55024 and EN 60950-1

• IEC 60950-1

• IC

• IEC/EN-60950

• RoHS/WEEE compliant

Environmental • Temperature (Operating): 32° F to 104° F (0°C to 40°C)

• Temperature (Storage): 4° F to 140° F (-20°C to 60°C)

• Humidity (Operating): 20% to 85% RH

• Humidity (Storage): 5% to 85% RH

• Power ("Heat") Dissipation:

On: 18.5 BTU/hr

Standby: 10.6 BTU/hr

Included

Accessories

• MXA-USB-C, USB Port Cover Kit (FG5968-18)

• MXA-CLK, Modero X/S Series Cleaning Kit (FG5968-16)

• MXD-700 Installation Template

Sleep ButtonNFC Sensor

Sleep

NFC

Button

MXD-700-L

MXD-700-P

Sensor

FIG. 2 MXD-700 BACKBOX (REAR VIEW)

FIG. 3 MXD-700 (LANDSCAPE)

Locking tab

RJ45 cable clip

RJ45 Cable/Port

Backbox

Backbox knockouts (X4)

Locking tabs (X2)

registered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks

of their respective companies.

AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153

AMX (UK) LTD, AMX by HARMAN - Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/

93-5968-08 REV: M

Last Revised: 6/22/2015

9. Insert each connector into its corresponding location along the back of the device. To

reach the RJ45 connector, gently pull it from beneath the electronics cover. Attach the

Ethernet cable and gently push the connection back under the cover.

Note: To facilitate connection of the RJ45 connector to the Ethernet cable, press the

RJ45’s cable into the RJ45 cable clip to hold it in a stable position. Make sure to remove

the cable from the cable clip before continuing the rest of the installation.

10. Test the incoming wiring by attaching the panel connections to their terminal locations

and applying power. Verify that the panel is receiving power and functioning properly to

prevent repetition of the installation.

Note: Do not disconnect the connectors from the touch panel. The unit must be installed

with the attached connectors before being inserted into the mounting surface.

Remove power before continuing with the installation.

11. Latch the panel onto the top hooks on the Backbox and push it down (Landscape) onto

the bottom snaps or on the left side and push it to the right (Portrait) (FIG. 5). Press

gently but firmly on the ends until the snaps “click” to lock it down.

WARNING: If you see a gap between the panel and the Backbox, or feel any binding while locking

down the panel, stop immediately and verify that no cables or other items are in the way. Do not

force the panel into position, as this can cause damage to the touch screen or the panel

electronics.

12. Reconnect the terminal Ethernet and USB to their respective locations on the Ethernet

port.

Powering On/Off X Series Panels

Modero X Series touch panels may be powered on by touching and holding the Sleep button.

To power off the panel, press and hold the Sleep button, and select Power Off on the on-

screen menu (FIG. 6):

Conf iguration and Programming

X Series touch panels are equipped with a Settings menu that provides the ability to configure

various features on the panels. To access the Settings menu, press and hold the Sleep button,

and select Settings.

Note: Information on the Settings menu, panel conf iguration, and programming is provided in

the Modero X Series Programming Guide, available at www.amx.com.

Setting the Panel’s Device Number and Device Name

1. In the Settings menu, select NetLinx. This opens a password keypad.

2. Enter the panel password into the keypad (the default is ) and select 1988 OK to access

the NetLinx page.

3. Press Device Number to open the NetLinx editing window.

4. Enter a unique Device Number assignment for the panel and press OK.

5. Enter a unique Device Name assignment for the panel and press OK.

Conf iguring the Panel’s IP Address

These steps configure the panel to communicate with a network; it is still necessary to

connect to the NetLinx Master (see Connecting to a NetLinx Master below).

Network Communication via DHCP

1. In the Ethernet page, press DHCP/Static field to open the DHCP/Static window. Note

that DHCP is the default setting.

2. Select Host Name, enter the new host name

3. Press OK to save changes.

Network Communication via Static Address

1. In the Ethernet page, press DHCP/Static to open the DHCP/Static window.

2. Select Static to open the Static IP window.

3. Press any field to open a keypad or keyboard (depending on the field), and enter the

appropriate network address information.

4. Press OK to save your changes and return to the Ethernet page.

Connecting to a NetLinx Master

To establish the type of connection to make between the panel and the NetLinx Master:

1. In the NetLinx page, press Mode to choose the connection mode (URL, Listen or Auto):

2. If password security is enabled on the target Master, enter the Username and

Password:

a. Select Username to open the NetLinx window.

b. Enter the Username and Password required by the Master.

c. Press OK to save changes and return to the NetLinx page.

Related Software and Additional Documentation (at www.amx.com)

• Programming the Modero X Series touch panels requires the use of the latest versions of

NetLinx Studio and TPDesign4, both available to download at www.amx.com. Refer to the

NetLinx Studio and TPDesign4 online help for information.

• For additional information on the MXD-700 panel, refer to the X-Series Touch Panels

MXD/T-1000, MXD/T-700 & MXD-430 Instruction Manual.

• For detailed information on the Settings menu as well programming information and

instructions on upgrading firmware, refer to the Modero X Series Programming Guide.

FIG. 4 MXD-700 BACKBOX INSTALLATION (LANDSCAPE)

FIG. 5 INSTALLING THE MXD-700

FIG. 6 SLEEP BUTTON - PRESS AND HOLD TO ACCESS POWER OFF/SETTINGS OPTIONS

#4 Screws

4X Knock-Outs

Remove for Cable

Routing as Needed

2X Installation Clamp

for Wall Thickness

.37 [12.03] to .98 [.25.0]

Mounting Surface

Backbox

Latch Hooks

Snaps

CONNECTION MODES

Mode Description Procedures

URL The device connects to the

target Master’s IP address

via a TCP connection.

1) Select URL in the Mode menu.

2) Enter the Master IP/URL, Master Port

Number, and Username/Password (if

required by the Master).

Press OK to save changes.

Listen This mode allows the panel

to “listen” for the Master’s

communication signals.

Note that in this mode, the

System Number and Master

IP/URL fields are read-only.

1) Select Listen in the Mode menu.

2) Confirm the panel’s IP address is on the

Master’s URL list (via NetLinx Studio).

3) Press OK to save changes.

Note: The Host Name (set on the Ethernet

page), can be used to locate the panel on the

Master (particularly useful for DHCP

connections where the IP address can change).

Auto Use this mode when both

the panel and the NetLinx

Master are on the same

Subnet.

1) Select Auto in the Mode menu.

2) Enter the System Number and Username

and Password (if applicable).

3) Press OK to save changes.

Especificaciones del producto

Marca:	AMX
Categoría:	No categorizado
Modelo:	MXD-700-NC

¿Necesitas ayuda?

Si necesitas ayuda con AMX MXD-700-NC haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado AMX Manuales

AMX HPX-MSP-7-SL Manual de Usario

18 Septiembre 2024

AMX HPX-MSP-10-SL Manual de Usario

18 Septiembre 2024

AMX TPC-WIN8-TAB Manual de Usario

17 Septiembre 2024

AMX NMX-DEC-N1222A Manual de Usario

16 Septiembre 2024

AMX NMX-DEC-N2222A Manual de Usario

16 Septiembre 2024

AMX NMX-DEC-N1233 Manual de Usario

16 Septiembre 2024

AMX NMX-DEC-N2211 Manual de Usario

16 Septiembre 2024

AMX NMX-ENC-N1134A Manual de Usario

16 Septiembre 2024

AMX NMX-ENC-N1133 Manual de Usario

16 Septiembre 2024

AMX NMX-ENC-N2315-WP Manual de Usario

16 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024