Asus M2NPV-VM Manual de Usario
Asus
Placa madre
M2NPV-VM
Lee a continuación 📖 el manual en español para Asus M2NPV-VM (13 páginas) en la categoría Placa madre. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/13
Motherboard
M2NPV-VM
ASUS M2NPV-VM 1-7
Onboard LED
The motherboard comes with a standby power LED that lights up to indicate
that the system is ON, in sleep mode, or in soft-off mode. This is a reminder
that you should shut down the system and unplug the power cable before
removing or plugging in any motherboard component. The illustration below
shows the location of the onboard LED.
1.4 Before you proceed
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
• Unplug the power cord from the wall socket before touching any
component.
• Use a grounded wrist strap or touch a safely grounded object or a metal
object, such as the power supply case, before handling components to
avoid damaging them due to static electricity
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded antistatic
pad or in the bag that came with the component.
• Before you install or remove any component, ensure that the ATX power
supply is switched off or the power cord is detached from the power
supply. Failure to do so may cause severe damage to the motherboard,
peripherals, and/or components.
M2NPV-VM
®
M2NPV-VM Onboard LED
SB_PWR
ON
Standby
Power
OFF
Powered
Off
ASUS M2NPV-VM 1-21
1.8 Expansion slots
In the future, you may need to install expansion cards. The following sub-sections
describe the slots and the expansion cards that they support.
1.8.1 Installing an expansion card
To install an expansion card:
1. Before installing the expansion card, read the documentation that came with
it and make the necessary hardware settings for the card.
2. Remove the system unit cover (if your motherboard is already installed in a
chassis).
3. Remove the bracket opposite the slot that you intend to use. Keep the screw
for later use.
4. Align the card connector with the slot and press rmly until the card is
completely seated on the slot.
5. Secure the card to the chassis with the screw you removed earlier.
6. Replace the system cover.
1.8.2 Conguring an expansion card
After installing the expansion card, congure it by adjusting the software settings.
1. Turn on the system and change the necessary BIOS settings, if any. See
Chapter 2 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the tables on the next page.
3. Install the software drivers for the expansion card.
Make sure to unplug the power cord before adding or removing expansion
cards. Failure to do so may cause you physical injury and damage motherboard
components.
Especificaciones del producto
| Marca: | Asus |
| Categoría: | Placa madre |
| Modelo: | M2NPV-VM |
¿Necesitas ayuda?
Si necesitas ayuda con Asus M2NPV-VM haz una pregunta a continuación y otros usuarios te responderán
Placa madre Asus Manuales
11 Octubre 2024
7 Octubre 2024
2 Octubre 2024
30 Septiembre 2024
30 Septiembre 2024
29 Septiembre 2024
27 Septiembre 2024
21 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
Placa madre Manuales
- Placa madre Sharkoon
- Placa madre Gigabyte
- Placa madre Asrock
- Placa madre Supermicro
- Placa madre Evga
- Placa madre Intel
- Placa madre MSI
- Placa madre ECS
- Placa madre NZXT
- Placa madre Foxconn
- Placa madre Elitegroup
- Placa madre EPoX
- Placa madre Biostar
Últimos Placa madre Manuales
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
20 Octubre 2024
19 Octubre 2024