Atdec TH-2050-UFL Manual de Usario

Atdec No categorizado TH-2050-UFL

Lee a continuación 📖 el manual en español para Atdec TH-2050-UFL (3 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/3
Component Checklist
Coach Screw (x3)
Nylon Anchor (x3)
Washer (x3)
4mm
Allen Key
M4x16mm
M5x16mm
M6x16mm/25mm
M8x16mm/25mm
TH-2050-UFL
Small-Medium TV Articulated Arm
IMPORTANT INFORMATION:
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
! IMPORTANT - Install 2050 Small-Medium TV Articulated Arm per Installation Instructions.
! This product supports a maximum load of 25kg (55lbs).
! This product supports VESA mounting hole configurations 200mm wide x100mm high to 400mm wide x 400mm high.
! The manufacturer accepts no responsibility for incorrect installation.
Display Mounting
Screws (x4 each)
Hardware
Tools Required:
Power drill
4.5mm (0.18”) drill bit
10.5mm (0.41”) masonry drill bit
Phillips head screw driver
10mm (0.39”) socket wrench or shifter
Step 2. Install Arm/Wall Mount to the Wall
Step 3. Attach Top Caps to the installed Arm/Wall Mount
Top Cap (x2)
Arm/Wall Mount
Mounting Bracket (x2)
Multiwasher (x4)
Timber Stud Wall
Masonry Wall
- Drill three 10.5mm (0.41”) diameter holes,
58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws and Nylon Anchors supplied.
- Drill three 4.5mm (0.18”) diameter holes, 58mm (2.3”) deep.
- Secure the mounting plate to the wall using the Coach
Screws supplied.
NOTE: Use a stud finder to accurately locate the centre
of the stud. Ensure that all screws fix securely into stud.
OR
SLIDE
End Cap (x2)
Locking Block (x2)
End Cap Screw (x4)
Coach Screw
Washer
End Cap
Screw
Nylon Anchor
Drilled Hole
End Cap
Coach Screw
Washer
End Cap
Screw
Drilled Hole
End Cap
SLIDE
SLIDE
Top Cap
13mm (0.5”) socket wrench or shifter
Installation Instructions
Step 4. Attaching Mounting Brackets to Display
TOP
Back of Display
Display Mounting Screw
Multiwasher
Mounting Bracket
Step 6. Attach Locking Blocks to fully secure the Display
WALL
Pull down both Spring Lock
Ties to open catch.
Hook the Display
to the Arm/Wall
Mount.
The mounting brackets support
hole configurations from
200x100mm to 400x400mm.
1 HOOK
3 PUSH
DOWN
1 HOOK
2 LOCK 4
2 PULL
DOWN
3 PUSH
DOWN
Push down Display into catch. Release Spring Lock Ties
to secure Display.
NOTE: Ensure that Spring
Lock is fully engaged.
RELEASE 4
Step 5. Attaching/Detaching Display to the installed Arm (2 people required)
Back of Display
Locking Blocks
Back of Display
4mm Allen Key
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 26.04.12 ©
Step 7. Adjust Arm movement if necessary
Step 8. Adjust tilt and roll if necessary
Socket Wrench
LOOSEN
(-kg)
TIGHTEN
(+kg)
-5°
+15°
±5°
WALL
±180°
Position your display to the
desired viewing angle, using the
angular movement allowed by
the double ball mount.
Depending on the weight of the
Display, it may be necessary to
make adjustments to the double
ball mount. If the display does
not hold its position, or is too
resistant, adjust the tension
plate located at the rear of the
double ball mount.
To adjust the tension plate, apply
half a turn at a time to each nut.
ENSURE NUTS ARE ADJUSTED
EVENLY.
CHECK THE DISPLAY, and then
adjust again if necessary.
±90°
Step 9. Cable Management
Back of Display
±90°

Especificaciones del producto

Marca: Atdec
Categoría: No categorizado
Modelo: TH-2050-UFL

¿Necesitas ayuda?

Si necesitas ayuda con Atdec TH-2050-UFL haz una pregunta a continuación y otros usuarios te responderán




No categorizado Atdec Manuales

No categorizado Manuales

Últimos No categorizado Manuales