AXESS AXAC-MZ2 Manual de Usario

Lee a continuación 📖 el manual en español para AXESS AXAC-MZ2 (16 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/16
AXAC-MZ2
I N S TA L L AT I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2023 METRA ELECTRONICS CORPORATION REV. 1/31/23 INSTAXAC-MZ2
ATTENTION: With the key out of the
ignition, disconnect the negative battery
terminal before installing this product.
Ensure that all installation connections,
especially the air bag indicator lights, are
plugged in before reconnecting the battery
or cycling the ignition to test this product.
NOTE: Refer also to the instructions
included with the aftermarket accessory
before installing this device.
INTERFACE FEATURES
TOOLS REQUIRED
INTERFACE COMPONENTS
REQUIRED ITEMS
TABLE OF CONTENTS
Introduction............................................................2
Configuration .....................................................2-4
Connections ............................................................5
Installation .............................................................6
Programming .........................................................6
(4) Camera inputs
Reverse signal trigger generated via CAN bus communication of the vehicle
Turn signal trigger generated via CAN bus communication of the vehicle
(4) Programmable camera control wires
Micro-B USB updatable
• Crimping tool and connectors, or solder gun,
solder, and heat shrink
• Tape • Wire cutter • Zip-ties
• AXAC-MZ2 interface
• AXAC-MZ2 interface harness
• AXAC-MZ2 vehicle harness (qty. 2)
18-pin T-harness
28-pin T-harness (cam harness)
Update Cable: AXUSB-MCBL (sold separately)
Axxess Updater Program
With full color LCD screen
Mazda† Camera Interface with Pre-Wired Harness
2014-Up
APPLICATIONS
Mazda
CX-3 2016-Up
CX-9 2016-Up
Mazda 3 2014-Up
Note: Only compatible with NTSC cameras.
Visit AxxessInterfaces.com for more detailed information
about the product and up-to-date vehicle specific applications
2
CONFIGURATION
Download and install the Axxess Updater available at: AxxessInterfaces.com
Connect the AXUSB-MCBL update cable (sold separately) between the interface and the computer.
The cable will connect into the micro-B USB port in the interface.
Open the Axxess Updater and wait until the word is listed in the bottom left of the screen.Ready
Select Add-Cam Configuration.
Continued on the next page
INTRODUCTION
The AXAC-MZ2 is a camera switching interface that provides up to (3) additional camera inputs
to the factory radio, while still retaining the factory camera. With this interface a front camera,
and/or side cameras, can be added to the factory radio. The cameras function automatically, no
human interaction required, unless desired to do so. The interface can also be used if the vehicle
doesn’t come equipped with a backup camera, adding up to (4) cameras in this scenario. Axxess
recommends cameras from the iBEAM product line for best results.
3
REV. 1/31/23 INSTAXAC-MZ2
Under Configuration, configure the (4) video trigger inputs to the desired settings.
Once all selections have been configured, press Write Configuration to save the settings.
Unplug the update cable from the interface and computer.
Refer to the following page for more information.
CONFIGURATION (CONT.)
Continued on the next page
Select the vehicle in the drop down list. A tab labeled Configuration will appear after the
vehicle has been selected.

Especificaciones del producto

Marca: AXESS
Categoría: No categorizado
Modelo: AXAC-MZ2

¿Necesitas ayuda?

Si necesitas ayuda con AXESS AXAC-MZ2 haz una pregunta a continuación y otros usuarios te responderán




No categorizado AXESS Manuales

No categorizado Manuales

Últimos No categorizado Manuales