AXESS AXDIS-GMLN11 Manual de Usario

AXESS No categorizado AXDIS-GMLN11

Lee a continuación 📖 el manual en español para AXESS AXDIS-GMLN11 (12 páginas) en la categoría No categorizado. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/12
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
AXDIS-GMLN11
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 1/22/20 INSTAXDIS-GMLN11
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell
caps, etc.) • Small flat-blade screwdriver
TABLE OF CONTENTS
Connections to be made ................................... 2-4
- For models
without
an amplifier .......................2
- For models
with
an analog amplifier ................3
- 3.5mm jack steering wheel control retention 4 ..
Installing the AXDIS-GMLN11 .................................4
Programming the AXDIS-GMLN11....................................5
Adjusting the AXDIS-GMLN11 .................................5
Steering wheel control settings .......................6-8
- L.E.D. feedback ....................................................6
- Changing radio type ...........................................6
- Remapping the steering wheel control buttons ... 7
- Dual assignment instructions (long button press) ...8
Troubleshooting .....................................................9
GM Data Interface with SWC 2006-2012
APPLICATIONS
Provides accessory power
(12-volt 10-amp)
Retains R.A.P. (retained
accessory power)
Provides NAV outputs (parking
brake, reverse, speed sense)
Retains chimes
Retains audio controls on the
steering wheel
Retains OnStar / OE Bluetooth
Adjustable OnStar level
Retains the factory AUX-IN jack
Can be used in non-amplified
or amplified models
Retains balance and fade
Micro “B” USB updatable
• AXDIS-GMLN11 interface • AXDIS-GMLN11 harness
• 16-pin harness with stripped leads • 4-pin to 4-pin resistor pad harness
• Female 3.5mm connector with stripped leads
CHEVROLET
Cobalt 2007-2010
HHR 2006-2011
Malibu 2008-2012
PONTIAC
G5 2007-2009
G6 (5th digit of VIN must
be a J, K, or L) 2009
PONTIAC (CONT)
G6 2010
Solstice 2006-2009
SATURN
Aura 2007-2009
Sky 2007-2009
2
CONNECTIONS TO BE MADE
Attention! This interface will work with models that are either factory amplified, or non-
amplified. Please follow the instructions carefully for your model vehicle. Failure to do so will
result in either no sound, or low sound. If you are unsure if your vehicle is factory amplified or
not, please contact your local dealership.
For models
without
an amplifier:
From the 16-pin harness with stripped leads to the aftermarket radio:
Connect the wire to the accessory wire.Red
Connect the wire to the amp turn on wire. This wire must be connected for the Blue/White
audio controls on the steering wheel to function.
If the aftermarket radio has an illumination wire, connect the wire to it.Orange/White
If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute wire is
not connected, the radio will turn off when OnStar is activated.
Connect the wire to the right front positive speaker output.Gray
Connect the Gray/Black wire to the right front negative speaker output.
Connect the wire to the left front positive speaker output.White
Connect the wire to the left front negative speaker output.White/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the wire to the VSS/speed sense wire.Blue/Pink
Connect the wire to the reverse wire.Green/Purple
Connect the Light Green wire to the parking brake wire
Tape off and disregard the following (4) wires, they will not be used in this application:
Green Green/Black Purple Purple/Black, , , .
From the AXDIS-GMLN11 harness to the aftermarket radio:
Connect the wire to the ground wire.Black
Connect the Yellow wire to the battery wire.
Cut off the resistors from the , , , and wires below the Green Green/Black Purple Purple/Black
heat shrink.
Connect the Green wire to the left rear positive speaker output.
Connect the Green/Black wire to the left rear negative speaker output.
Connect the wire to the right rear positive speaker output.Purple
Connect the wire to the right rear negative speaker output.Purple/Black
Ensure the (2) 4-pin Molex connectors are connected together.
Note:
The 4-pin to 4-pin resistor pad harness will not be used in this application.
The Black/Yellow wire is used for OnStar level adjustment for models that do not come
equipped with steering wheel controls. Refer to the OnStar level Adjustment section for
further instructions.
Connect the and RCA jacks to the audio AUX-IN jacks of the aftermarket radio.Red White
Disregard the DIN jack and wire.Red
Continue to 3.5mm jack steering wheel control retention
3
REV. 1/22/2020 INSTAXDIS-GMLN11
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the wire to the VSS/speed sense wire.Blue/Pink
Connect the wire to the reverse wire.Green/Purple
Connect the Light Green wire to the parking brake wire
Tape off and disregard the following (4) wires, they will not be used in this application:
Green Green/Black Purple Purple/Black, , ,
From the AXDIS-GMLN11 harness to the aftermarket radio:
Connect the wire to the ground wire.Black
Connect the Yellow wire to the battery wire.
Connect the wire to the left rear positive speaker output.Green
Connect the wire to the left rear negative speaker output.Green/Black
Connect the wire to the right rear positive speaker output.Purple
Connect the wire to the right rear negative speaker output.Purple/Black
Disconnect the (2) 4-pin Molex connectors, and then attach the 4-pin to 4-pin resistor pad harness.
The Black/Yellow wire is used for OnStar level adjustment for models that do not come
equipped with steering wheel controls. Refer to the OnStar level Adjustment section for
further instructions.
Connect the and RCA jacks to the audio AUX-IN jacks of the aftermarket radio.Red White
Disregard the DIN jack and wire.Red
Continue to 3.5mm jack steering wheel control retention
Attention! This interface will work with models that are either factory amplified, or non-
amplified. Please follow the instructions carefully for your model vehicle. Failure to do so will
result in either no sound, or low sound. If you are unsure if your vehicle is factory amplified or
not, please contact your local dealership.
For models
with
an amplifier:
From the 16-pin harness with stripped leads to the aftermarket radio:
Connect the wire to the accessory wire.Red
Connect the wire to the amp turn on wire. This wire must be connected to hear Blue/White
sound from the factory amplifier, and also for the audio controls on the steering wheel to
function.
If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
If the aftermarket radio has a mute wire, connect the Brown wire to it. If the mute wire is
not connected, the radio will turn off when OnStar is activated.
Connect the wire to the right front positive speaker output.Gray
Connect the Gray/Black wire to the right front negative speaker output.
Connect the wire to the left front positive speaker output.White
Connect the wire to the left front negative speaker output.White/Black
CONNECTIONS TO BE MADE (CONT)

Especificaciones del producto

Marca: AXESS
Categoría: No categorizado
Modelo: AXDIS-GMLN11

¿Necesitas ayuda?

Si necesitas ayuda con AXESS AXDIS-GMLN11 haz una pregunta a continuación y otros usuarios te responderán




No categorizado AXESS Manuales

No categorizado Manuales

Últimos No categorizado Manuales