AXESS AXFRC-GM2 Manual de Usario

Lee a continuación 📖 el manual en español para AXESS AXFRC-GM2 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
AXFRC-GM2
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 10/20/21 INSTAXFRC-GM2
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
NOTE: Refer to the instructions included with
the aftermarket radio.
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Wire cutter
• Crimp tool and connectors
(example: butt-connectors, bell caps, etc.)
or
• Solder gun, and solder, heat shrink
• Tape
• Zip-tie
TABLE OF CONTENTS
Connections ............................................................2
Configuring the AXFRC-GM2 ..................................3
Installation .............................................................4
User guide ..............................................................5
GM HDMI and Camera Interface 2013-Up
Provides front and rear camera inputs to the factory radio
Provides an HDMI input to the factory radio
(AXHDM-1M cable sold separately)
USB Micro B updatable
AXFRC-GM2 interface
AXFRC-GM2 harness
6-pin to USB cable
LVDS (video) to USB cable
10-pin harness with RCA jacks
3.5mm extension cable
APPLICATIONS
See inside front cover
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date
vehicle specific applications
2
CONNECTIONSAPPLICATIONS
If installing a front/rear camera, connect the wire labeled “GND”, Black
to the camera(s) ground wire.
If installing a backup camera, connect the wire labeled “Reverse Camera 12v”, Red
to the backup camera power wire.
If installing a front camera, connect the wire labeled “Front Camera 12v”, Red
to the front camera power wire.
The wire labeled “Acc Power Output” is optional if a power source is required Red
while a camera is active.
If installing a backup camera, connect the Yellow RCA jack labeled “Reverse Camera Video
Input” to the camera.
If installing a front camera, connect the
Yellow
RCA jack labeled “Front Camera Video Input” to the
camera
.
If adding an HDMI input to the factory radio, connect an HDMI cable (AXHDM-1M, sold
separately), to the port on the AXFRC-GM2 labeled “HDMI IN”, and then to the media device.
FRONT CAM IN
REAR CAM IN
ACC PWR OUT
REAR CAM PWR
FRONT CAM PWR
CAM GROUND
HDMI LVDS OUT LVDS IN AV IN
POWER
IN
(Connections Diagram)
CHEVROLET (1)
Colorado 2017-2018
Cruze 2016-2018
Equinox 2018
Silverado 1500/2500/3500 2016-2018
GMC (2)
Acadia 2017-Up
Canyon 2017-2018
Sierra 1500/2500/3500 2016-2018
HOLDEN (1)
Astra 2017-Up
Barina 2017-Up
Captiva 2017-Up
Colorado 2017-Up
Commodore 2017-Up
Spark 2017-Up
Trailblazer 2017-Up
Trax 2017-Up
Ute 2017-Up
OPEL VAUXHALL (3)
Adam 2013-Up
Astra (K) 2017-Up
Corsa (E) 2014-Up
Crossland X 2017-Up
Grandland X 2017-Up
Karl 2015-Up
Zafira Tourer 2017-Up
Viva 2015-Up
(1) For models with a 7-inch MyLink radio
(2) For models with a 7-inch IntelliLink radio
(3) For models with a R 4.0 7-inch IntelliLink radio
3
REV. 10/20/21 INSTAXFRC-GM2
Dip switch settings
Remove the access door located on the top of the AXFRC-GM2 interface to access the dip switches.
Dip 1
If the vehicle is equipped with a factory
backup camera: Yes NoOn: Off:
Dip 3
If the vehicle has an aftermarket
backup camera
: Yes NoOn: Off:
Dips 4 & 5
For all applications:
Dip 4:
Off
Dip 5:
Off
Dip 2
If the vehicle has an aftermarket front
camera:
Yes NoOn: Off:
CONFIGURING THE AXFRC-GM2

Especificaciones del producto

Marca: AXESS
Categoría: No categorizado
Modelo: AXFRC-GM2

¿Necesitas ayuda?

Si necesitas ayuda con AXESS AXFRC-GM2 haz una pregunta a continuación y otros usuarios te responderán




No categorizado AXESS Manuales

No categorizado Manuales

Últimos No categorizado Manuales