AXESS AXGM-07 Manual de Usario

Lee a continuación 📖 el manual en español para AXESS AXGM-07 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
Installation instructions for part AXGM-07
REV. 1/20/2020 INSTAXGM-07
axxessinterfaces.com metraonline.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
Axxess Integrate
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
Provides accessory power (12-volt
10-amp)
Retains R.A.P. (retained accessory
power)
Provides NAV outputs (parking brake,
reverse, speed sense)
Retains chimes to the factory speaker
Adjustable chime level
Retains OnStar / OE Bluetooth
Adjustable OnStar level
Designed for non-amplified models,
or when bypassing a factory amp *
Retains balance and fade
USB-CAB updatable (sold separately)
INTERFACE FEATURES
Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
• Small flat-blade screwdriver
TOOLS REQUIRED
AXGM-07
GM Data Interface
2005-2006
APPLICATIONS
AXGM-07 interface • AXGM-07 harness
• 16-pin harness with stripped leads
INTERFACE COMPONENTS
Connections to be made 2 ...................................................
Installing the AXGM-07 3 ....................................................
Initializing the AXGM-07 3 ..................................................
Adjusting the AXGM-07 3 ....................................................
Table of Contents
CHEVROLET
Equinox 2005-2006
PONTIAC
Torrent 2006
* If the vehicle is amplified, either use the AXGM-08 interface, or bypass the amplifier. If
bypassing the amplifier, follow the Axxess Interface Amp Bypass Schematic” online.
AXGM-07
From the 16-pin harness with stripped leads to the aftermarket radio:
• Connect the wire to the accessory wire.Red
• If the aftermarket radio has an illumination wire, connect the Orange/White
wire to it.
Note: If the wire on the AXGM-07 harness is populated on the factory Orange
side, use that wire instead.
• If the aftermarket radio has a mute wire, connect the wire to it. If the Brown
mute wire is not connected, the radio will turn off when OnStar is activated.
• Connect the wire to the right front positive speaker output.Gray
• Connect the wire to the right front negative speaker output.Gray/Black
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the wire to the VSS/speed sense wire.Blue/Pink
• Connect the wire to the reverse wire.Green/Purple
• Connect the wire to the parking brake wire.Light Green
Connections to be made
From the AXGM-07 harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the battery wire.
• Connect the wire to the power antenna wire.Blue/White
• Connect the wire to the left rear positive speaker output.Green
• Connect the wire to the left rear negative speaker output.Green/Black
• Connect the wire to the right rear positive speaker output.Purple
• Connect the wire to the right rear negative speaker output.Purple/Black
The Black/Yellow wire is used for OnStar level adjustment for models that
do not come equipped with steering wheel controls. See the OnStar level
Adjustment section for further instructions.
AXGM-07
Installing the AXGM-07
Initializing the AXGM-07
With the key in the off position:
• Connect the 16-pin harness with stripped leads, and the AXGM-07 harness, into
the interface.
• Connect the AXGM-07 harness to the wiring harness in the vehicle.
Attention! If the interface loses power for any reason, the following steps will need
to be performed again. Also, if installing an AXSWC connect it after you initialize and
test the interface/radio, with the key in the off position.
• Turn the key (or push-to-start button) to the ignition position and wait until the
radio comes on.
Note: If the radio does not come on within 60 seconds, turn the key to the
off position, disconnect the interface, check all connections, reconnect the
interface, and then try again.
• Turn the key to the off position, and then to the accessory position. Test all
functions of the installation for proper operation, before reassembling the dash.
Adjusting the AXGM-07
Chime level adjustment:
• Turn the vehicle off but leave the keys in the ignition. Open the driver’s door and
leave it open; chimes will be heard.
• Wait 10 seconds, and then with a small flat-blade screwdriver, adjust the
potentiometer clockwise to raise the chime level; counterclockwise to lower the
chime level.
Note: The potentiometer is located on the side of the interface where the 16-
pin harness with stripped leads is connected to.
• When the chime is at the desired level, remove the keys from the ignition. This
will lock the chime level in at its current level.
OnStar level adjustment:
• Press the OnStar button to activate it.
• While OnStar is speaking, press the VOLUME UP or VOLUME DOWN buttons on
the steering wheel to raise or lower the OnStar level.
• If the vehicle does not come equipped with steering wheel controls, locate the
Black/Yellow wire on the AXGM-07 harness.
• While OnStar is speaking, tap the Black/Yellow wire to ground. Once the
OnStar level is set, it will stay at that level until the Black/Yellow wire is tapped
to ground again.

Especificaciones del producto

Marca: AXESS
Categoría: No categorizado
Modelo: AXGM-07

¿Necesitas ayuda?

Si necesitas ayuda con AXESS AXGM-07 haz una pregunta a continuación y otros usuarios te responderán




No categorizado AXESS Manuales

No categorizado Manuales

Últimos No categorizado Manuales