AXESS AXHN-1 Manual de Usario

AXESS No categorizado AXHN-1

Lee a continuación 📖 el manual en español para AXESS AXHN-1 (4 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
AXHN-1
I N S TA L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 1/22/20 INSTAXHN-1
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Small flat-blade
screwdriver • Tape • Wire cutter • Zip ties
TABLE OF CONTENTS
Connections to be made ....................................... 2
Installing the AXHN-1 ............................................. 3
Programming the AXHN-1 .....................................3
Setting the factory clock ....................................... 3
Troubleshooting .....................................................3
Honda Clock Retention 2012-2014
APPLICATIONS
• Provides accessory power (12-volt 10-amp)
• Can be used in non-amplified, or amplified models
• Provides NAV outputs (parking brake, reverse, speed sense)
• AXSWC harness included (AXSWC sold separately)
• Retains balance and fade
• Retains the ability to set the factory clock
• Retains the factory AUX-IN jack
• Micro-B USB updatable
• AXHN-1 interface • AXHN-1 harness
• 8-pin subwoofer harness
• 16-pin harness with stripped leads
HONDA
Civic * (without NAV) 2013 CR-V (without NAV) 2012-2014
* All trims except LX
2
CONNECTIONS TO BE MADE
From the 16-pin harness with stripped leads to the aftermarket radio:
• Connect the wire to the accessory wire.Red
• Connect the Orange/White wire to the illumination wire. If the aftermarket radio does not
have an illumination wire, tape it off and disregard it.
• Tape off and disregard the , Gray Gray/Black White White/Black Brown, , , and wires, they
will not be used in this application.
The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the wire to the parking brake wire (if applicable).Light Green
• Connect the wire to the VSS or speed sense wire (if applicable).Blue/Pink
• Connect the wire to the reverse wire (if applicable).Green/Purple
From the AXHN-1 harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the battery wire.
• If the vehicle is equipped with a factory amplifier, connect the Blue/White wire to amp
turn-on wire.
• If the vehicle is equipped with a factory AUX-IN jack and desired to be retained, connect the
Red & RCA jacks to the AUX-IN jack.White
For the following (8) wires, if the vehicle does not have a factory amplifier, cut off the RCA jacks
to expose the speaker wires.
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
• Connect the wire to the right front positive speaker output.Gray
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the wire to the left rear positive speaker output.Green
• Connect the wire to the left rear negative speaker output.Green/Black
• Connect the wire to the right rear positive speaker output.Purple
• Connect the wire to the right rear negative speaker output.Purple/Black
From the 8-pin subwoofer harness to the aftermarket radio (amplified models only):
• Connect the RCA to the subwoofer output. White
12-pin pre-wired AXSWC harness:
• This harness is to be used along with the optional AXSWC (not included) to retain steering
wheel audio controls. If the AXSWC is not being used, disregard this harness. If it will be
used, please refer to the AXSWC instructions for radio connections and programming.
Disregard the harness that comes with the AXSWC.
• For the CR-V 2014: If the vehicle is equipped with Bluetooth controls, and desired to be
retained, connect the Gray/Blue wire to the Yellow wire (pin-15) in the 32-pin harness at the
factory Bluetooth module located in the center of the dash, below the radio.
3
REV. 1/22/2020 INSTAXHN-1
With the key in the off position:
• Connect the 16-pin harness with stripped leads, and the AXHN-1 harness, into the interface.
• If an AXSWC (sold separately) will be used, do not connect it until the AXHN-1 is programmed
and fully functional.
Attention! Do not connect the AXHN-1 harness to the wiring harness in the vehicle just yet.
For the steps below, the L.E.D. located inside the interface can only be seen while active. The
interface does not need to be opened to see the L.E.D.
1. Start the vehicle.
2. Connect the AXHN-1 harness to the wiring harness in the vehicle. The L.E.D. will initially be
Green to indicate the interface is powered.
3. After a few seconds the L.E.D. will turn on solid while the interface automatically Red
programs to the vehicle. The radio will shut off at this point. This process should take 5 to 30
seconds.
4. After the interface is programmed, the L.E.D. will turn on solid , and the radio will Green
come back on, indicating programming was successful.
5. Test all functions of the installation for proper operation, before reassembling the dash.
6. If the interface fails to function, refer to “Troubleshooting”.
Resetting the Axxess interface
1. The reset button is located inside the Axxess interface, between the two connectors. Blue
The button is accessible outside the Axxess interface, no need to open the Axxess interface.
2. Press and hold the reset button for two seconds, then let go to reset the Axxess interface.
3. Refer to “Programming the Axxess Interface” from this point.
The buttons on the steering wheel will be used to set the factory clock.
• Press and hold the SOURCE button on the steering wheel for 15 seconds to access the clock
setting mode.
• Press SEEK-UP or SEEK-DOWN to select hours, minutes, etc. Press VOLUME-UP or
VOLUME-DOWN to set the values.
•
Either press SOURCE again, or wait 5 seconds with no activity to exit the clock setting mode
.
INSTALLING THE AXHN-1
PROGRAMMING THE AXHN-1 TROUBLESHOOTING
SETTING THE FACTORY CLOCK

Especificaciones del producto

Marca: AXESS
Categoría: No categorizado
Modelo: AXHN-1

¿Necesitas ayuda?

Si necesitas ayuda con AXESS AXHN-1 haz una pregunta a continuación y otros usuarios te responderán


No categorizado AXESS Manuales

AXESS

AXESS AXDSPX-BM1 Manual de Usario

25 Octubre 2024
AXESS

AXESS AXBUCS-MZ286V Manual de Usario

19 Septiembre 2024
AXESS

AXESS 99-7014HG Manual de Usario

19 Septiembre 2024
AXESS

AXESS AXGM-17 Manual de Usario

19 Septiembre 2024
AXESS

AXESS AXGMLN-34 Manual de Usario

19 Septiembre 2024
AXESS

AXESS 99-7382HG Manual de Usario

19 Septiembre 2024
AXESS

AXESS GMOS-12 Manual de Usario

19 Septiembre 2024
AXESS

AXESS XSVI-1788-NAV Manual de Usario

19 Septiembre 2024
AXESS

AXESS 99-7510HG Manual de Usario

19 Septiembre 2024
AXESS

AXESS AXBUCS-NI246V Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024