AXESS AXVI-6524 Manual de Usario

Lee a continuación 📖 el manual en español para AXESS AXVI-6524 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
AXVI-6524
I N S TA L L AT I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2023 METRA ELECTRONICS CORPORATION REV. 2/24/23 INSTAXVI-6524
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrinkTape • Wire cutter
• Zip ties
TABLE OF CONTENTS
Connections .........................................................2-3
Installation .............................................................3
Programming .........................................................3
App Instructions .................................................4-5
Jeep/Ram Select Models Data Interface 2014-Up
Provides accessory power
(12-volt 10-amp)
Retains R.A.P. (retained
accessory power)
Provides NAV outputs (parking
brake, reverse, speed sense)
Pre-wired AXSWC harness
(AXSWC sold separately)
Retains the factory backup
camera (Not retained on
Wrangler JL or Gladiator)
Retains balance and fade
Designed for non-amplified
models
Retains the factory AUX-IN jack
Allows retention and adjustment
of the Personalization Options*
Adjust Personalization Options
through a Bluetooth application*
Smartphone application offering
full control from either Android or
Apple mobile devices
Micro-B USB updatable
AXVI-6524 interface
AXVI-6524 harness
2-pin CAN harness
OPTIONAL ACCESSORIES
(sold separately)
Steering wheel control interface:
AXSWC OBD T-harness: AX-IL-OBD2
APPLICATIONS
* Actual options available vary per vehicle and per trim.
(Refer to owner’s manual for options available in vehicle)
Jeep
Gladiator* 2020-Up
Renegade 2015-2017
Renegade Sport 2018
Wrangler* JL (Base model) 2018-Up
Ram
Promaster (w/color screen) 2014-Up
Promaster City 2015-Up
* Camera will not be retainedNote:
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections, especially the air
bag indicator lights, are plugged in before
reconnecting the battery or cycling the
ignition to test this product.
NOTE: Refer also to the instructions included
with the aftermarket accessory before
installing this device.
Visit AxxessInterfaces.com for more detailed information about the
product and up-to-date vehicle specific applications
2
CONNECTIONS
From the AXVI-6524 harness harness to the aftermarket radio, connect as indicated:
Connect the wire to the ground wire.Black
Connect the Yellow wire to the battery wire.
Connect the (3) wires to the accessory wire.Red
If installing an (sold separately), there will be an accessory wire there to Note: AXSWC
connect as well.
If the aftermarket radio has an illumination wire, connect the wire to it.Orange
Connect the Gray wire to the right front positive speaker wire.
Connect the Gray/Black wire to the right front negative speaker wire.
Connect the wire to the left front positive speaker wire.White
Connect the wire to the left front negative speaker wire.White/Black
Connect the wire to the left rear positive speaker wire.Green
Connect the wire to the left rear negative speaker wire.Green/Black
Connect the wire to the right rear positive speaker wire.Purple
Connect the to the right rear negative speaker wire.Purple/Black
The following (3) wires are only for multimedia/navigation radios that require these wires.
Connect the wire to the VSS/speed sense wire.Blue/Pink
Connect the wire to the reverse wire.Green/Purple
Connect the wire to the parking brake wire.Light Green
Tape off and disregard the following (2) wires, they will not be used in this application:
Blue/White (qty. 2)
If retaining the factory backup camera, connect the Yellow RCA jack to the backup camera input
.
Note: For Wrangler JL and Gladiator the camera is not retained. You must purchase the
JP-JLKT for the JL and the JP-JTKT for the Gladiator to retain the camera
If retaining the factory AUX-IN jack, connect the & RCA jacks to the AUX input.Red White
Continued on the next page
3
REV. 2/24/23 INSTAXVI-6524
CAN connections to the vehicle:
Disconnect the 2-pin connector AXVI-6524 harness from the .
Connect the
2-pin CAN harness to the AXVI-6524 harness.
Route the harness to the vehicles OBD port located under the driver’s side dash.
Option 1 (excluding Wrangler)
Connect the wire to the CAN-HI wire. (Figure A)White/Red
Connect the White/Green wire to the CAN-LO wire. (Figure A)
Option 2
Use part number AX-IL-OBD2 to “T” into the OBD port.
AX-IL-OBD2 Wiring (sold separately)
Locate the wires that have the #1 on them
Color match the wires to the 2pin CAN harness
Connect them back into the 2pin that was disconnected from the AXVI-6524
12-pin pre-wired AXSWC harness:
This harness is to be used along with the (sold separately) to retain steering wheel audio AXSWC
controls. If the is not being used, disregard this harness. If it is to be used, please refer to the AXSWC
AXSWC instructions for radio connections and programming. Disregard the harness that comes with
the .AXSWC
With the key in the off position:
1. Connect the AXVI-6524 harness to the AXVI-6524 interface, and then to the wiring
harness in the vehicle.
2. If an AXSWC (sold separately) will be used, do not connect it until the AXVI-6524 is
programmed and fully functional.
CONNECTIONS (CONT.) INSTALLATION
(Figure A) Attention!
If the interface ever loses power, the following steps will need to be performed
again. Please ensure that the owner of the vehicle knows this.
1. Turn the key (or push-to-start button) to the ignition position and wait until the radio
comes on.
Note: If the radio doesn’t not come on within 60 seconds, turn the key to the off
position, disconnect the interface, check all connections, reconnect the interface, and
then try again.
2. Turn the key (or push-to-start button) to the off position, then open and close the
driver’s door.
3. Wait 5 minutes for the vehicle to fully go to sleep.
4. Start the vehicle, then test all functions of the installation for proper operation.
PROGRAMMING

Especificaciones del producto

Marca: AXESS
Categoría: No categorizado
Modelo: AXVI-6524

¿Necesitas ayuda?

Si necesitas ayuda con AXESS AXVI-6524 haz una pregunta a continuación y otros usuarios te responderán




No categorizado AXESS Manuales

No categorizado Manuales

Últimos No categorizado Manuales