Ballymore M-2000 154014 Manual de Usario

Ballymore Escalera M-2000 154014

Lee a continuación 📖 el manual en español para Ballymore M-2000 154014 (3 páginas) en la categoría Escalera. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

15 0144

Ballymore Part # 15 0144

Inspect the ladder for ipping dama prior starting assembly. there evidence shipping damage notify sh ge to If is of

the rrier immediately.ca

STEP 1 - ASSEMBLE TOP STEP

- Place Stair Section (A) face down attach Top ep (C) i fo washers (7) and locknuts (8 Tighten bolts and St us ng ur ).

completely

STEP 2 - ATTACH LOCKSTEP

- Attach Lockst the bottom step using ur washers (7) locknuts (8). Tighten bolts completely. ep (B) to fo and

STEP 3 ATTACH VERTICAL WELDMENT

- Align wLo er Vertical Weldment (G- & Upp Vertical Weldme -2) i M8 x bolts (6) with washe (7) 1) er nt (G us ng 60 rs

and locknuts (8).

- Place Vertic Weldme (G) onto back Stair Section and i kets on top Vertical Weldme (G) al nt of (A) al gn brac of nt

with bs otruding from bottom Top Step (C). Ta pr of

- Use x bolts (2) with wa eM8 25 sh rs ). (7) a cknuts ( fasten Vertical Wel (G) a Section (And lo 8) to dment to St ir

- tighten bolts. Do not

STEP 4 - ATTACH BASE WELDMENT

- Align Base Weldment (H) with the bs the Front Legs ladder. Note The cast s point for this Ta on of : er up

alignment.

- Use two x 20 bolts (1) with washers (7), and locknuts (8) fasten the Base Weldm (H) the Front g M8 to ent to Le s.

Do tighte not n.

STEP 5 - CO E BASE WELDM T AND REAR VERTIC WELDMENTSNN CT EN AL

- Pivot weldments into position the An Steel With Rigid Ca eso gle st r and re vertical conn t. Align the hole the ar ec in

Angle Steel With Rigid Caster with the hole the ba the vertic and bolt together i X bolts (5in se of al us ng M8 50 )

with washers (7) a lo nut(8). Ta care not nd ck ke to over tighten.

STEP 6 - INSTALL BRACES

- Install Vertical Braces (J), Horizontal Braces (K) and Diagonal ace (L) using x bolts (1), x bolts (2) Br M8 20 M8 25

and 50 x M8 bolts (5) with wa e (7) a locknuts (8). sh rs nd

If you purchased the All Directional Option s ll now, follow the directions included wiin ta it th your kit when

complete return step 7to

Get assistan stand the ladder up. easiest way to stand the ladder rst lay side. Once the ce to The up is to it on it’s

ladder had been sto od up take a at ace relea the lock step dropping f legs the ladder the it to surf se ront of to

ground. ke sure the ladder rmly the ground and tighten all bolts.Ma is on

STEP 7- ASSEMBLE HANDRAIL CONFIGURATION CAREFUL WHEN ASSEMBLI HANDRAIL WE –BE NG –

RECOMMEND A SPOTTER ASSIST THIS STEPTO IN

- Bolt Rear drail (D) the Top Step (C) using M8 x bolts (1 washers (7) and locknuts (8). Guar to 20 ),

- nnect Top ndrails (E Rear Guardrail (D) using x bolts (3), wash s (7) locknuts (8 Co Ha ) to M8 40 er and ).

Note Handrail stiener should be positioned the outside Stair Section (A : on of ).

- Attach ndrail Bracket (I) the Top Handrail i x Ha to us ng M8 55 bolts (4), washers (7) a lond cknuts (8). Note :

Handrail Brackets (I) sh ld position the insi Stair Section (A). Conrm Re G drail (D) is ou be ed on de of ar uar

per end ar and bolp i lcu the Top Step (C), to tighten the ts.

- Mount Lower ndrails (F) using Ha a Brackets (I) x bolts (4) and waHa ndr il and M8 55 she (7), locknuts (8). Note : rs

Top Lower ndrail o butt against Top Handrail. of Ha sh uld

- Tighten hardware. all

STEP 8 FINAL INSPECTION

- k see that ladder sits level oor. After conrming that dder ts level, tighten hardware. Conrm Chec to on la si all all

bolts have operly tightene been pr d.

- ad instructi manuRe on al and become familiar with oper usa a maintenanc pr ge nd e.

- nnect instruction maCo nual the ladder, insure ers ad important safety information. to all us re

Ballymore Part # 15 0144

PARTS LIST

PART # DESCRIPTION QUANTITY

A STAIR SECTION 1

B LOCKSTEP 1

C TOP STEP 1

D REAR GUARDRAIL 1

E TOP HANDRAIL 2

F LOWER HANDRAIL 4

G-1 LOWER VERTICAL WELDME 1NT

G-2 P VERTICAL WELDME 1UP ER NT

H BASE WELDME 1NT

I HANDRAIL BRACKET 10

J RTICAL BRACE 2VE

K HORIZONTAL BRACE 2

L DIAGONAL BRACE 2

M ANGLE STEEL WITH RIGID CASTER 1

1 BOLT X 10M8 20

2 BOLT X 4M8 25

3 BOLT X 4M8 40

4 BOLT X 20M8 55

5 BOLT X 4M8 50

6 BOLT X 2M8 60

7 WASHER 8 96

8 LOCKNUT 8 52

Especificaciones del producto

Marca:	Ballymore
Categoría:	Escalera
Modelo:	M-2000 154014
Colocación del dispositivo:	Aanrecht
Tipo de operación:	Buttons, Rotary
Color del producto:	Black, Stainless steel
Pantalla incorporada:	Ja
Peso.:	3600 g
Ancho:	288 mm
Profundidad:	200 mm
Altura:	314 mm
Longitud del cable:	0.95 m
Activos:	1100 W
Capacidad del tanque de agua:	1.25 l
Certificación:	CE
Tipo de entrada de café:	Gemalen koffie
Depósito para café preparado:	Beker
Capacidad en tazas:	- kopjes
Molino incorporado:	Nee
Haciendo café:	Ja
hacer espresso:	Ja
hacer capuchino:	Ja
Tanque de agua extraíble:	Ja
Carga de trabajo máxima:	15 bar
Placa antiderrames extraíble:	Ja
Espumador de leche incorporado:	Ja
Hacer café con leche macchiato:	Ja
Plato caliente:	Ja
voltaje-de-entrada-de-CA:	220 - 240 V
Frecuencia-de-entrada-de-CA:	50 Hz
Tipo-producto:	Espressomachine
Tipo-de-visualización:	Analoog