Best Ispira ICB3I36SBN Manual de Usario

Best campana extractora Ispira ICB3I36SBN

Lee a continuación 📖 el manual en español para Best Ispira ICB3I36SBN (48 páginas) en la categoría campana extractora. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/48

ICB3I SERIES

HB0117

INSTALLATION INSTRUCTIONS

INTENDED FOR DOMESTIC COOKING ONLY

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 TO 14.

READ AND SAVE THESE INSTRUCTIONS

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711

BEST; Drummondville, QC, Canada www.BestRangeHoods.ca 866-737-7770

23866 rev. 03

! !

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by

qualified personnel in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guidelines and safety standards such as

those published by the National Fire Protection Association

(NFPA) and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE) and the local code

authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented outdoors.

7. Do not use this unit with any additional solid-state speed

control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

10. All tempered glass can experience spontaneous breakage. If

broken, tempered glass falls out of its opening in interlocking

clumps. Tempered glass can, on occasion, break into large

shards rather than the classic tiny piece pattern.

11. When applicable, local regulations comprise more

restrictive installation and/or certification requirements,

the aforementioned requirements prevail on those of this

document and the installer agrees to conform to these at his

own expense.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils

slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or when

flambeing food (i.e.: Crêpes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan, filters or in exhaust ducts.

d) Use proper pan size. Always use cookware appropriate for the

size of the surface element.

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

4. Your hood motor has a thermal overload which will automatically

shut off the motor if it overheats. The motor will restart when it

cools down. If the motor continues to shut off and restart, have

the hood serviced.

5. The hood distance above cooktop must not be less than 30”.

A maximum of 36” above cooktop is highly recommended for

best capture of cooking impurities.

6. Two installers are recommended because of the large size and

weight of this unit.

7. To reduce the risk of fire and to properly exhaust air, be sure to

duct air outside — Do not exhaust air into spaces within walls

or ceiling or into attics, crawl space or garage.

8. Because of the high exhausting capacity of this unit, you

should make sure enough air is entering the house. Open a

window close to or in the kitchen.

9. To reduce the risk of fire and electrical shock, the Best ICB3I

Series models should only be installed with their own built-in

blower.

10. Please read specification label on product for further

information and requirements.

11. This hood is equipped with an RF receiver. See next page for

related warning.

WARNING

CAUTION

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE

THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT

BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels —

This could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

A. You own a Class ABC extinguisher and you know how to

operate it.

The fire is small and contained in the area where it started.B.

The fire department has been called.C.

You can fight the fire with your back to an exit.D.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

WARNING

This hood is equipped with a RF receiver (optional remote control sold separately). Changes or modifications

not expressly approved by the party responsible for compliance could void the user’s authority to operate this

product. The remote control has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules and the Canadian ICES-003. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. The remote control generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

TABLE OF CONTENTS

1. INSTALL DUCTWORK ................................................................................................................................................................................... 3

2. PREPARE INSTALLATION ............................................................................................................................................................................... 4

3. MEASURE INSTALLATION .............................................................................................................................................................................. 4

4. INSTALL MOUNTING BRACKET ........................................................................................................................................................................ 5

5. ASSEMBLE ANGLE BRACKETS ........................................................................................................................................................................ 6

6. REMOVE HYBRID FILTERS ............................................................................................................................................................................. 7

7. INSTALL GLASS PANELS SBN MODEL ONLY ( ) ...................................................................................................................................................... 7

8. PREPARE HOOD ALL MODELS ( ) .................................................................................................................................................................. 8-9

9. INSTALL HOOD ...................................................................................................................................................................................... 9-10

10. CONNECT WIRING .....................................................................................................................................................................................11

11. REINSTALL HYBRID FILTERS .........................................................................................................................................................................11

12. LED LIGHTING .........................................................................................................................................................................................12

13. CARE .....................................................................................................................................................................................................12

14. OPERATION ........................................................................................................................................................................................ 13-14

15. WIRING DIAGRAM ......................................................................................................................................................................................14

16. SERVICE PARTS ........................................................................................................................................................................................15

17. WARRANTY .............................................................................................................................................................................................16

1. INSTALL DUCTWORK

Plan where and how the ductwork will be installed.

A straight, short duct run will allow the hood to perform most efficiently.