Boss RC-1 Manual de Usario

Boss sistema de alta fidelidad RC-1

Lee a continuación 📖 el manual en español para Boss RC-1 (1 páginas) en la categoría sistema de alta fidelidad. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/1
Owner’s Manual
* 5100069045- 01*
Basic Operation
To perform recording, overdubbing, and playback, press the pedal as shown in the diagram.
Technique for stopping
Example: When you want to stop at the end of a
measure with a 4/4 time signature
Press the pedal one time at the beginning of
the fourth beat, then press it once again at the
beginning of the rst beat of the next measure.
1st time 2nd time
1 2 3 4 1
Stop
Loop Playback
Play back a phrase as a loop.
Pressing the pedal switches
the unit to overdubbing.
Overdubbing
Layer your performances while
the phrase plays as a loop.
Pressing the pedal switches the
unit to playback.
Recording
Record your
guitar or bass
performance.
Stop
During overdubbing or loop playback, you
can stop by pressing the pedal twice in
succession.
* Press the pedal twice within one second.
Press twice
Lit red and
green
Lit greenLit red
Deleting a Phrase
The recorded phrase is erased if you hold down the pedal for two seconds or
longer while stopped.
During erasure, the LOOP indicator (red) blinks rapidly.
* Never turn o the power while the LOOP indicator (red) is blinking rapidly. The
recorded data might be lost if you do so.
* The phrase plays while you hold down the pedal. If you want to erase the
phrase without playing it, use an external footswitch to stop the phrase.
Cancelling an Overdub (Undo/Redo)
You can undo/redo by holding down the pedal for two seconds or longer during
overdubbing or playback.
Operation Explanation
Undo Cancels the last recording or overdub.
Redo
To bring back the cancelled sound, hold down the pedal once
again for two seconds or longer during playback.
* Redo is possible only during overdubbing or playback.
During undo/redo, the LOOP indicator (green) blinks rapidly.
Connecting to an External Footswitch
Connect your footswitch to the STOP/UNDO jack as shown in the illustration, and
set its POLARITY switch.
* The FS-5L cannot be used.
FS-7
FS-6
FS-5UFS-5U
1/4” phone type
10 1/4” phone
type
Stereo 1/4” phone
type 1/4” 10
phone type x 2
Stereo 1/4” phone
type Stereo 1/4” 10
phone type
Footswitch Operation
FS-5U Stop
During recording/overdubbing/playback,
press the footswitch to stop.
Erase the phrase
Hold down the footswitch two seconds or
longer to erase the phrase.
FS-5U/FS-7 pedal connected
to the stereo L side
FS-6’s pedal B
FS-5U/FS-7 pedal connected
to the stereo R side Undo/Redo
You can undo/redo by pressing the footswitch.
FS-6’s pedal A
Changing the Recording Mode/Stop Mode/Display Mode
1. While holding down the pedal switch, turn the power on (insert a plug into
the OUTPUT A jack).
The LOOP indicator (red) lights, indicating the current recording mode.
Recording mode Explanation
Red
Upper
half
Switch in the order of recording overdubbing 0
0 playback.
Lower
half
Switch in the order of recording playback 0 0
overdubbing (default setting).
2. Press the pedal switch successively twice (within one second) to change the
recording mode.
3. Press the pedal switch.
The LOOP indicator (green) lights, indicating the current stop mode.
Stop mode Explanation
Green
Upper
half
Press the pedal switch successively twice to stop
immediately (default setting).
Lower
half
Press the pedal switch successively twice to
enable stopping at the end of the phrase;
playback stops when the phrase has played to its
end. When playback stops, the phrase is erased.
Operation when stop has been enabled
• The LOOP indicator (green) rotates while
blinking.
• Press the pedal switch successively twice to
stop immediately and erase the phrase.
• Hold down the pedal switch for two seconds
or longer to cancel the stop-enabled state.
4. Press the pedal switch successively twice (within one second) to change the
stop mode.
5. Press the pedal switch.
The LOOP indicator (red and green) lights, indicating the current display mode.
Display mode Explanation
Red
and
Green
Upper
half
The rotational speed of the LOOP indicator
changes according to the length of the recorded
phrase (default setting).
Lower
half
The LOOP indicator rotates rapidly; then the
playback location blinks.
6. Press the pedal switch successively twice (within one second) to change the
stop mode.
7. When the power is turned o and on again, the unit returns to normal
operation.
Changing the Battery
1. Hold down the pedal and loosen the
thumbscrew, then open the pedal upward.
* The pedal can be opened without detaching
the thumbscrew completely.
2. Remove the old battery from the battery
housing, and remove the snap cord
connected to it.
3. Connect the snap cord to the new battery,
and place the battery inside the battery
housing.
* Be sure to carefully observe the battery’s
polarity (+ versus -).
4. Slip the coil spring onto the spring base on
the back of the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing.
5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely.
Specications
BOSS RC-1: Loop Station
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output Level -20 dBu
Output Impedance 1 kΩ
Recommended Load Impedance 10 kΩ or greater
Maximum Recording Time Approx. 12 minutes
Power Supply DC 9 V: Alkaline battery (9 V, 6LR61), AC Adaptor (PSA
series: sold separately)
Current Draw
95 mA * Expected battery life under continuous use:
Alkaline: Approx. 3 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
Weight 430 g/1 lb (including battery)
Accessories
Owner’s Manual,
Leaet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,”
and “Information”), Alkaline battery (9 V, 6LR61)
Options (sold separately) AC adaptor: PSA series
Footswitch: FS-5U, FS-6, FS-7
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the time that the document was
issued. For the latest information, refer to the Roland website.
About the Battery
• Batteries should always be installed or replaced before connecting any other devices. This way,
you can prevent malfunction and damage.
• The use of an AC adaptor is recommended as the unit’s power consumption is relatively high.
Should you prefer to use battery, please use the alkaline battery.
• If you handle batteries improperly, you risk explosion and uid leakage. Make sure that you
carefully observe all of the items related to batteries that are listed in “USING THE UNIT SAFELY”
and “IMPORTANT NOTES.”
Repairs and Data
• Although we will do our utmost to preserve the data stored in your unit when we carry out
repairs, in some cases, such as when the memory section is physically damaged, restoration of
the stored content may be impossible. Roland assumes no liability concerning the restoration
of any stored content that has been lost.
Intellectual Property Right
• It is
forbidden by law to make an audio recording, video recording, copy or revision of a third
party’s copyrighted work (musical work, video work, broadcast, live performance, or other
work), whether in whole or in part, and distribute, sell, lease, perform, or broadcast it without
the permission of the copyright owner.
• Do not use this product for purposes that could infringe on a copyright held by a third party.
We assume no responsibility whatsoever with regard to any infringements of third-party
copyrights arising through your use of this product.
• Roland, BOSS, and Loop Station are either registered trademarks or trademarks of Roland
Corporation in the United States and/or other countries.
• Company names and product names appearing in this document are registered trademarks or
trademarks of their respective owners.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
9 V Battery
DC IN jack
Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without being
concerned about how much battery power you have left.
* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the
correct voltage. Do not use any other AC adaptor, since this may cause malfunction.
* If the AC adaptor is connected a battery is installed, the power supply is drawn from the AC
adaptor.
* We recommend that you keep batteries installed in the unit even though you’ll be powering it
with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the
AC adaptor gets accidently disconnected from the unit.
CHECK indicator
This indicator shows the power on/o status, and also provides a battery check function.
* If you’re powering the unit with a battery and the CHECK indicator goes dim—or doesn’t light at all—the battery is
near depletion and should be replaced. For instructions on changing the battery, refer to “Changing the Battery.”
Panel Descriptions
OUTPUT jacks A (MONO)/B
Connect these jacks to your amp or monitor speakers.
If you’re using a mono setup, use the OUTPUT A jack.
* The OUTPUT A jack also operates as a power switch. The power
will be on if a plug is inserted in the OUTPUT A jack. Remove the plug
when you’re not using the RC-1.
* Do not connect headphones to the OUTPUT jacks. Doing so may
damage the headphones.
Thumbscrew
When this screw is loosened, the pedal will open,
allowing you to change the battery.
* For instructions on changing the battery, refer to
“Changing the Battery.”
INPUT jacks A (MONO)/B
Connect your electric guitar, or another instrument or eect unit, to these jacks.
LEVEL knob
This adjusts the volume level of the loop phrase being played back.
* The input level from the INPUT jacks cannot be adjusted.
AC Adaptor
(PSA series: sold
separately)
Guitar
Amplier
* Use the INPUT A jack and INPUT B jack when
connecting a stereo-output eects unit. Use only
the INPUT A jack if you’re using a mono source.
MEMO
• If a footswitch is connected to the STOP/UNDO jack, you can stop by
pressing the footswitch just once.
• The recorded phrase is saved even if you turn o the power.
NOTE
• The minimum recording time for a loop phrase is approximately 0.25
seconds. If you press the pedal within approximately 0.25 seconds after
you start recording, recording will continue until the phrase is at least
approximately 0.25 seconds long.
• The maximum recording time for a loop phrase is approximately 12
minutes (stereo). If you exceed the maximum recording time, recording
or overdubbing is interrupted, and operation changes to loop playback.
• Roland assumes no liability concerning the restoration of any stored
content that has been lost.
Pedal switch
This pedal switches you between phrase recording, overdubbing, and playback. Press
the pedal twice in succession to stop playback.
If you hold down the pedal two seconds or longer while stopped, the recorded phrase
is erased.
STOP/UNDO jack
If you connect a footswitch (FS-5U, FS-6, FS-7: sold separately), you can
use it to stop playback or to undo/redo.
LOOP indicator
This lights during recording, overdubbing, and playback.
Indicator Explanation
Red During recording
Red and green During overdubbing
Green During playback
* During overdubbing/playback,
the speed at which the indicator
rotates corresponds to the length
of the loop.
English
Precautions When Connecting
* To prevent malfunction and equipment failure, always turn down the volume, and turn o all the units before making any
connections.
* Raise the amp volume only after turning on the power to all connected devices.
* When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the
battery as soon as possible.
* When connection cables with resistors are used, the volume level of equipment connected to the INPUT jacks may be low.
If this happens, use connection cables that do not contain resistors.
Caution When Connecting an External Footswitch
You must power-o the unit before connecting an external footswitch.
If you connect the footswitch while the power is on, recorded data might be lost.
Turning On the Power
Inserting a connecting plug into the OUTPUT A jack turns on the power to the unit.
Once the connections have been completed, turn on power to your various devices in the order specied. By turning on
devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.
When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.
* This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will
operate normally.
* Before turning the unit on/o, always be sure to turn the volume down. Even with the volume turned down, you might
hear some sound when switching the unit on/o. However, this is normal and does not indicate a malfunction.
Caution when turning o the power
Never turn o the power while the LOOP indicator is rotating or blinking (i.e., don’t pull the plug out of the OUTPUT A
jack). The recorded data might be lost if you do so.
© 2014 Roland Corporation
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
Electric Guitar

Especificaciones del producto

Marca: Boss
Categoría: sistema de alta fidelidad
Modelo: RC-1

¿Necesitas ayuda?

Si necesitas ayuda con Boss RC-1 haz una pregunta a continuación y otros usuarios te responderán


sistema de alta fidelidad Boss Manuales

Boss

Boss Riot R3400D Manual de Usario

1 Septiembre 2024
Boss

Boss ARMOR AR2000M Manual de Usario

28 Agosto 2024
Boss

Boss MCK1308WB.64 Manual de Usario

28 Agosto 2024
Boss

Boss 638BCK Manual de Usario

28 Agosto 2024
Boss

Boss ARMOR AR1600.2 Manual de Usario

28 Agosto 2024
Boss

Boss MCK1440W.6 Manual de Usario

28 Agosto 2024
Boss

Boss MCK1440W.64 Manual de Usario

28 Agosto 2024
Boss

Boss Chaos EPIC CE200M Manual de Usario

28 Agosto 2024
Boss

Boss MCK752WB.6 Manual de Usario

27 Agosto 2024
Boss

Boss 628UA Manual de Usario

26 Agosto 2024

sistema de alta fidelidad Manuales

Últimos sistema de alta fidelidad Manuales

Morel

Morel MXT280C Manual de Usario

27 Octubre 2024
Rotel

Rotel RSP-975 Manual de Usario

27 Octubre 2024
Motu

Motu Audio Express Manual de Usario

27 Octubre 2024
Rockford Fosgate

Rockford Fosgate HD9813SGU-STAGE2 Manual de Usario

26 Octubre 2024
Thomson

Thomson MIC123BT Manual de Usario

26 Octubre 2024
Samsung

Samsung MAX-KC930 Manual de Usario

25 Octubre 2024
Samsung

Samsung MM-ZL7 Manual de Usario

25 Octubre 2024
Philips

Philips FWM996X Manual de Usario

24 Octubre 2024
Sony

Sony MHC-RV333D Manual de Usario

21 Octubre 2024
Sony

Sony MHC-FR10 Manual de Usario

20 Octubre 2024