Broan BCSD124SS Manual de Usario

Broan campana extractora BCSD124SS

Lee a continuación 📖 el manual en español para Broan BCSD124SS (63 páginas) en la categoría campana extractora. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/63
RANGE HOOD
Series: BCSD
INSTALLATION, USE
AND CARE MANUAL
WWW.BROAN.COM
Serial number:
99045652-102G
INSTALLATION MANUAL
TABLE OF CONTENTS
2
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Cleaning and Maintenance . . . . . . . . . . . . . . . . . 6
Motor
Grease Filters
Non-Ducted Recirculation Filters
Fan Blade
Stainless Steel Cleaning
Painted Finish Cleaning
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20
Recommended Tools
and Accessories for Installation . . . . . . . . . . . . 7
Install Ductwork (Ducted Installations Only) . . . 7
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Prepare the Hood . . . . . . . . . . . . . . . . . . . . . . . 9-11
Prepare the Hood Location . . . . . . . . . . . . . . . . 12
EZ1 One-person Installation . . . . . . . . . . . . . 12-14
Install the Hood (EZ1 Bracket) . . . . . . . . . . . . 15-16
Standard Installation . . . . . . . . . . . . . . . . . . . 17
Install the Hood (Standard Installation) . . . . . 18
Connect the Wiring . . . . . . . . . . . . . . . . . . . . . . 19
Install the Light Bulbs . . . . . . . . . . . . . . . . . . . . 20
Install the Filters . . . . . . . . . . . . . . . . . . . . . . . . 20
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 21
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . 22-25
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
INSTALLATION MANUAL
SAFETY
3
READ AND SAVE THESE INSTRUCTIONS
! Intended for domestic cooking only !
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
Register your range hood online at www.broan.com
! WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
• Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer at the address or telephone number
listed in the warranty.
• Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to
the service panel.
• Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards, including
fire-rated construction.
• Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to prevent
backdrafting. Follow the heating equipment manufacturer’s guidelines and
safety standards such as those published by the National Fire Protection
Association (NFPA) and the American Society for Heating, Refrigeration
and Air Conditioning Engineers (ASHRAE) and the local code authorities.
• When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
• Ducted fans must always be vented to the outdoors.
• Do not use this unit with any additional solid-state speed control device.
• To reduce the risk of fire, use only metal ductwork.
• This unit must be grounded.
• As an alternative, this product may be installed with the UL-approved cord
kit designated for the product, following instructions packed with the cord
kit.
• When applicable local regulations comprise more restrictive installation
and/or certification requirements, the aforementioned requirements prevail
on those of this document and the installer agrees to conform to these at
his own expense.
INSTALLATION MANUAL
SAFETY
4
! WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause
smoking and greasy spillovers that may ignite. Heat oils slowly on low or
medium settings.
b) Always turn hood ON when cooking at high heat or when flambeing food
(i.e.: Crêpes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c) Clean ventilating fan frequently. Grease should not be allowed to
accumulate on fan, filters or in exhaust ducts.
d) Use proper pan size. Always use cookware appropriate for the size of
the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray,
then turn off the burner. BE CAREFUL TO PREVENT BURNS. IF THE
FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL
THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels — This could
cause a violent steam explosion.
4. Use an extinguisher ONLY if:
A. You own a Class ABC extinguisher and you know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department has been called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
! CAUTION
• For indoor use only.
• For general ventilating use only. Do not use to exhaust hazardous or explosive materials
and vapors.
• To avoid motor bearing damage and noisy and/or unbalanced fan blade, keep drywall
spray, construction dust, etc. off range hood.
• Your hood motor has a thermal overload which will automatically shut off the motor if it
becomes overheated. The motor will restart when it cools down. If the motor continues to
shut off and restart, have the hood serviced.
• For best capture of cooking fumes, the bottom of the hood MUST NOT BE LESS than 18”
and at a maximum of 24” above the cooking surface.
• Always follows the cooking equipment manufacturer’s requirements regarding the
ventilation needs.
• To reduce the risk of fire and to properly exhaust air, be sure to duct air outside — Do not
exhaust air into spaces within walls or ceiling or into attics, crawl space or garage.
• When installing, servicing or cleaning the unit, it is recommended to wear safety glasses
and gloves.
• Please read specification label on product for further information and requirements.
INSTALLATION MANUAL
OPERATION
5
Operation
Always turn your hood on before you begin cooking to establish an air flow in the kitchen.
Let the blower run for a few minutes to clear the air after you turn off the range. This will help
keep the whole kitchen cleaner and fresher.
Operate the hood as follows:
FAN SWITCH
I Turns fan on to LOW speed.
• Turns fan OFF.
II Turns fan on to HIGH speed.
LIGHT SWITCH
I Turns light on to LOW intensity.
• Turns light OFF.
II Turns light on to HIGH intensity.
INSTALLATION MANUAL
CLEANING AND MAINTENANCE
6
Cleaning and Maintenance
Proper maintenance of the Range Hood will assure proper performance of the unit.
MOTOR
The motor is permanently lubricated and never needs oiling. If the motor bearings make
excessive or unusual noise, replace the motor with the exact service motor. The fan blade should
also be replaced.
GREASE FILTERS
The grease filters should be cleaned frequently. Use a warm dishwashing detergent solution.
Grease filters are dishwasher safe.
Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the
filters may occur if using phosphate detergents, or as a result of local water conditions - but this
will not affect filter performance. This discoloration is not covered by the warranty. To minimize or
prevent discoloration, hand wash filters using a mild detergent.
NON-DUCTED RECIRCULATION FILTERS
The non-ducted recirculation filters should be changed every 3 to 6 months. Replace more often
if your cooking style generates extra grease, such as frying and wok cooking. Refer to installation
instructions included with non-ducted recirculation filters.
FAN BLADE
The fan blade should be cleaned frequently. Use a clean cloth soaked with warm detergent solution.
STAINLESS STEEL CLEANING
Do:
• Regularly wash with clean cloth or rag soaked with warm water and mild soap or liquid dish
detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely.
• You may also use a specialized household stainless steel cleaner.
Don’t:
• Use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.
• Use any harsh or abrasive cleansers.
• Allow dirt to accumulate.
• Let plaster dust or any other construction residues reach the hood. During construction/
renovation, cover the range hood to make sure no dust sticks to the stainless steel surface.
Avoid when choosing a detergent:
• Any cleaners that contain will attack stainless steel.bleach
• Any products containing: chloride, fl uoride, iodide, bromide will deteriorate surfaces
rapidly.
• Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc.,
are highly explosive and should never be used close to a range.
PAINTED FINISH CLEANING:
Clean with warm water and mild detergent only. If discoloration occurs, use a finish polish such
as automotive polish. (DO NOT use rough abrasive cleaner or porcelain cleaner.)
INSTALLATION MANUAL
INSTALLATION
7
Recommended Tools and Accessories
for Installation
• Measuring tape
• Phillips screwdriver no. 2
• Flat blade screwdriver (to open knockout holes)
• Drill, 1/8” drill bit and 1½” hole saw (to mark holes for ducting and cut electrical access hole)
• 7/64” drill bit (to drill holes for EZ1 brackets mounting screws)
• Wood shims (2) and wood screws (4) (required for standard installation to framed cabinet)
• Saw (to cut holes for ducted application)
• Sheet metal shears (ducted installation only, for duct adjustment)
• Pliers (ducted installation only, for duct adjustment)
• Metal foil duct tape (for ducted applications)
• Scissors (to cut metal foil duct tape)
• Pencil
• Wire stripper
• Strain relief, 1/2” diameter (to secure house wiring cable to the hood)
Install Ductwork (Ducted Installations Only)
SOFFIT
18" - 24" MIN MAX
ABOVE COOKING SURFACE
CABINET
3¼" 10" X DUCT
(F OR HORIZONTAL DISCHARGE )
W ALL CAP
R OOF CAP 3¼" 10" X OR
7" ROUND DUCT
(F OR VERTICAL
DISCHARGE)
H OUSE WIRING
(T )OP OR BACK OF HOOD
HOOD
NOTE: Distances over 24” are at the installer and user discretion.
1 ] Determine whether hood will discharge vertically (3¼” x 10” or 7” round),
or horizontally (3¼” x 10” only).
2 ] Decide where the ductwork will run between the hood and the outdoors.
3 ] Choose a straight, short duct run to allow the hood to perform most efficiently. Long duct
runs, elbows and transitions will reduce the performance of the hood. Use as few of them as
possible. When possible, use at least 2 foot straight runs before any turns. Larger ductwork
may be required for best performance with longer duct runs.
4 ] Install wall cap or roof cap (sold separately). Connect metal ductwork to cap and work back
towards the hood location. Use 2” metal foil duct tape to seal the joints between ductwork
sections.
For ADA compliance installation guidelines, please visit www.broan-nutone.com
INSTALLATION MANUAL
INSTALLATION
8
Contents
Before proceeding to the installation, check the contents of the box. If items are missing or
damaged, contact the manufacturer.
Make sure that the following items are included:
(2) G FREASE ILTERS
(1) 3¼” X 10”
DAMPER ASSEMBLY *
(1) 7” ROUND
D CUCT ONNECTOR
(1) P B *** CARTS AG ONTAINING:
* F IND INSIDE
OF HOOD
(2) INSTALLATION RACKETS B **
FOR FRAMED CABINET
(2) INSTALLATION RACKETS B **
FOR FRAMELESS CABINET
(1) TEMPLATE FOR DUCTING
( PRINTED BOTH SIDES )
(1) B SULB UCTION
CUP TOOL
(6) N 5/8”O. 8 X
RD. HD.
WOOD CREWS S
(4) N . 8-18 1/2”O X
METAL CREWS S
(6) N 1/2”O. 8 X
COUNTERSUNK
W S OOD CREWS
EZ1 COMPONENTS
** F EZ1 BIND RACKET
ATTACHED INSIDE OF HOOD
C
L
A B
Apoyar este borde contra l a pared de atrá sPlace thi s edge aga inst back wall
VERTICAL EXHAUST
S
A
A
V
RTICAL EX
= 3¼” x 10”
= 3¼” x 14”
R DECTANGULAR UCTING7” ROUND DUCTING OR
Use this template fo r marking; do not attempt to cut o ut the ducting hole through it.
NOTE: These cutouts are clearance holes; they do no t need to be the exact size o f ducting.
= 3¼ po x 10 po
= 3¼ po x 14 po
C ONDUITRECTANGULAIREC ONDUIT RONDDE 7 PO OU
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
C ONDUCTO RECTANGULARC ONDUCTO REDONDO
DE 7 PULG.O
Appuyer ce bord au mur arr ière
Utiliser ce gabarit pour marquer vo s repères; ne pas tenter de déco uper
le trou po ur le conduit à tra vers le gabarit.
NOTE : Les déco upes incluent le jeu nécessaire à l’installatio n; elles ne doivent pas
être du fo rmat exa ct des co nduits.
Use esta plantilla para crear ma rcado s; no tra te de co rtar el
agujero del co nducto a través de la plantilla.
NOTA: To be translated in Spanish.
M ARK WHEREINDICATED
FORTHE DUCTOPENING APPROPRIATE SIZ E
M ARQUER LES REPÈRESAUXENDROITS INDIQUÉS SELON
LE DE FORMAT CONDUIT UTILISÉ
T SITLETOBE TRANSLATED IN P ANISH
Electrical acces s ho le ce nter
A = s ingle blo wer ho o d
B = do uble blo we r ho o d
Centre du trou po ur fil
d’alimentatio n é lectrique
A = ho tte ve ntilateur s imple
B = ho tte ve ntilateur do uble
To be trans lated in S panish
Electrical acces s ho le ce nter
A = s ingle blo wer ho o d
B = do uble blo we r ho o d
4¼”
10½”
14½”
8”
7½”
CC
CBend template a long graduated
scale when installing to fra med
cabinet.
Po ur une installatio n sous une
armo ire à fo nd en retrait, utiliser les
lignes pour mesurer l’épaisseur du
décalage causé par le mur de
l’armo ire et plier le gabarit en
conséquence.
To be translated in Spanish.
*** F IND PA RTS BAG BEHIND
THE DAMPER ASSEMBLY
INSIDE
OF HOOD
INSTALLATION MANUAL
INSTALLATION
9
Prepare the Hood
1 ] If present, remove all protective polyfilm from the hood and/or parts.
2 ] Using the tab, remove the grease filters from the hood by pushing down and tilting filters out.
3 ] Remove both screws holding damper assembly to hood. Remove parts bag included with
the hood (captured behind the damper assembly).Remove damper assembly from inside the
hood and keep the screws for further use.
NOTE: Remove the EZ1 brackets from inside the hood by cutting off the tie wrap.
4 ] Remove the wiring cover (shaded part on illustration below) by sliding it out from the hood
and set it aside.
DAMPER
ASSEMBLY
SCREWS
EZ1
BRACKETS
INSTALLATION MANUAL
INSTALLATION
10
5 ] Remove 7” Round Duct Plate from top/back of hood (see illustration below).
RECIRCULATION
COVER PLATE
SCREWS
6 ] Remove Electrical Power Cable Knockout from top (vertical exhaust) or back (horizontal
exhaust) of hood. Install an appropriate strain relief, 1/2” diameter (not included).
NON-DUCTED INSTALLATION ONLY
7 ] Remove 3 screws retaining the recirculation cover plate (shaded part in illustration
below) to the hood. Discard this plate with its screws.
7” ROUND
DUCT
PLATE
2 SCREWS
ELECTRICAL
POWER CABLE
KNOCKOUT
INSTALLATION MANUAL
INSTALLATION
11
DUCTED INSTALLATION ONLY
TIP: Insert a small length of duct over the 3¼” x 10” damper assembly (for rectangular ducting)
or 7” round (for round ducting) and seal the joint using aluminum foil duct tape to ease
connection with the house ductwork.
8 ] Remove 3¼” x 10” vertical, 3¼” x 10” horizontal, or 7-inch round knockout plate as
appropriate for your ducting method (see FIGURES 1 A 1 Band ).
NOTE: To accommodate off-center ductwork, the 7” round duct plate can be installed up
to 1/2” on either side of the hood center.
7” ROUND KNOCKOUT
PLATE ( ALSO REMOVE
VERTICAL KNOCKOUT PLATE )
3¼” X 10”
VERTICAL
KNOCKOUT
PLATE 3¼” X 10”
HORIZONTAL
KNOCKOUT
PLATE
F 1 AIGURE
7” ROUND
DUCT
PLATE
SCREWS
F 3IGURE
3¼” X 10”
DAMPER
ASSEMBLY
TOP/BACK
EDGE OF
HOOD
DAMPER
FLAP
PIVOT
SCREWS
F 2 A F 2 BIGURE IGURE
9 ] Attach 3¼” x 10” Damper Assembly on top OR back of hood (if using 3¼” x 10” duct; shaded
part in FIGURE 2 A below) or 7” Round Duct Plate (if using 7-inch round duct, ) over FIGURE 3
the knockout opening. When installed, the 3¼” x 10” damper assembly must open as
shown in F 2 BIGURE .
F 1 BIGURE
3¼” X 10”
DAMPER
ASSEMBLY
BACK OF
HOOD
DAMPER
FLAP
PIVOT
SCREWS
INSTALLATION MANUAL
INSTALLATION
12
Prepare the Hood Location
NOTE: Before starting installation, read all the steps of these instructions.
Use the illustration below to identify your kitchen cabinet type.
EZ1 One-person installation system
EZ1 installation is designed for use with kitchen cabinets that have the same width designation as
the range hood width. If the cabinet is greater than 1/2” wider than the range hood width, please
use the standard installation method.
1 ] Use the proper template for vertical OR horizontal disharge (included) for placement of
ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a
duct access hole, only cut the hole for electrical wiring. If replacing a hood and plan to use
the existing duct and electrical, steps 2 to 5 may not be necessary. If so, skip to step 6.
2 ] Measure and mark the hood center line on cabinet bottom.
3 ] Align the center line on template with the hood center line marked on the bottom of the
cabinet, placing the edge (where indicated) of the template against back wall. When using
with framed cabinet for vertical exhaust installation, fold over rear edge of template equal
to the depth of the cabinet frame at the wall (use graduations on template, C locations on
template). Tape the template in place.
NOTE: When facing the installation, and (on template) must be at right.A B
This manual covers 2 kinds of installation: the standard (without EZ1 brackets) and the EZ1
one-person installation system (using included template and brackets). For the standard
installation, go to page 17.
FRAMED CABINET FRAMELESS CABINET
CABINET FRONT
C
L
A B
Apoyar este bo rde contra la pared de atrásPlace this ed ge aga inst ba ck wall
VERTICAL EXHAUST
A
S
A
A
V
RTICAL EX
= 3¼” x 10”
= 3¼” x 14”
R DECTANGULAR UCTING7” ROUND DUCTING OR
Use this te mplate f or marking; do not att e mpt t o cut o ut the ducting hole through it.
NOTE: Thes e cutouts are clearance holes ; they do not nee d to be the e xact s ize of ducting.
= 3¼ po x 10 po
= 3¼ po x 14 po
C ONDUIT RECTANGULAIREC 7 ONDUIT ROND DE PO OU
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
C ONDUCTO RECTANGULARC ONDUCTO REDONDO
DE 7 .PULG
O
Appuyer ce bord au mu r arrière
Utilise r ce gabarit pour marque r vos repè res ; ne pas te nter de déco uper
le tro u pour le conduit à travers le gabarit.
NOTE : Les dé coupes inclue nt le jeu néc es s aire à l’inst allation; e lle s ne do ivent pas
être du fo rmat exact des co nduits .
Use es ta plant illa para crear marcados; no trate de co rtar e l
aguje ro del co nducto a travé s de la plantilla.
NOTA: To be t rans lated in Spanish.
M ARK WHERE INDICATED
FOR THE APPROPRIATE SIZE DUCT OPENING
M ARQUER LES REPÈRESAUX ENDROITS INDIQUÉSSELON
LE DE FORMAT CONDUIT UTILISÉ
T SITLE TO BETRANSLATEDIN PANISH
Electrical access hole center
A = s ingle blower ho od
B = double blowe r hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur do uble
To be translated in Spanish
Electrical access hole center
A = s ingle blower ho od
B = double blowe r hood
4¼”
10½”
14½”
8”
7½”
CC
CBend template along graduate d
sc ale when ins talling to framed
cabinet.
Pour une installat ion sous une
armo ire à fond en retrait, ut ilise r les
lignes pour me s urer l’épaiss eur du
décalage caus é par le mur de
l’armoire e t plie r le gabarit en
consé quence .
To be t rans lated in Spanish.
P
C
CABINET FRONT
C
L
A B
A
S
A
A
V
RTICAL EX
= 3¼” x 10”
= 3¼” x 14”
R DECTANGULAR UCTING7” ROUND DUCTING OR
Use this te mplate f or marking; do not att e mpt t o cut o ut the ducting hole through it.
NOTE: Thes e cutouts are clearance holes ; they do not nee d to be the e xact s ize of ducting.
= 3¼ po x 10 po
= 3¼ po x 14 po
C ONDUIT RECTANGULAIREC 7 ONDUIT ROND DE PO OU
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
C ONDUCTO RECTANGULARC ONDUCTO REDONDO
DE 7 .PULG
O
Utilise r ce gabarit pour marque r vos repè res ; ne pas te nter de déco uper
le tro u pour le conduit à travers le gabarit.
NOTE : Les dé coupes inclue nt le jeu néc es s aire à l’inst allation; e lle s ne do ivent pas
être du fo rmat exact des co nduits .
Use es ta plant illa para crear marcados; no trate de co rtar e l
aguje ro del co nducto a travé s de la plantilla.
NOTA: To be t rans lated in Spanish.
M ARK WHERE INDICATED
FOR THE SIZE OPENING APPROPRIATE DUCT
M ARQUER LES REPÈRESAUX ENDROITS INDIQUÉSSELON
LE DE FORMAT CONDUIT UTILISÉ
T ITLE TO BETRANSLATEDIN SPANIS H
Electrical access hole center
A = s ingle blower ho od
B = double blowe r hood
Centre du trou pour fil
d’alimentation électrique
A = hotte ventilateur simple
B = hotte ventilateur do uble
To be translated in Spanish
Electrical access hole center
A = s ingle blower ho od
B = double blowe r hood
4¼”
10½”
14½”
8”
7½”
CC
CBend template along graduate d
sc ale when ins talling to framed
cabinet.
Pour une installat ion sous une
armo ire à fond en retrait, ut ilise r les
lignes pour me s urer l’épaiss eur du
décalage caus é par le mur de
l’armoire e t plie r le gabarit en
consé quence .
To be t rans lated in Spanish.
A
C
ELECTRICAL
ACCESS HOLE
LOCATION ( )A
(IN CABINET BOTTOM )
CENTER LINE
F OLD TEMPLATE ALONG GRADUATED
SCALE WHEN INSTALLING FRAMED TO
CABINET.
VERTICAL EXHAUST
DUCTING
Electrica l access hol
A = single blowe r ho
B = double blowe r
Centre d u tr
d’al im
ELECTRICAL
ACCESS HOLE
LOCATION ( )A
(IN WALL )
CENTER LINE
A
C
L
A B
Place this edge against
cabin et bottom.
Appuyer ce bord contre le bas
de l’armoire.
Apoyar este borde contra
la base del armario.
HORIZONTAL EXHAUST
T
T
= 3¼ pulg. x 10 pulg.
= 3¼ pulg. x 14 pulg.
C ONDUCTO RECTANGULAR
= 3¼” x 10”
= 3¼” x 14”
R DECTANGULAR UCTING
= 3¼ po x 10 po
= 3¼ po x 14 po
C ONDUITRECTANGULAIRE
M ARK WHEREINDICATED
FORTHEAP PROPRIATE DUCT OPENING SIZE M ARQUERLES REPÈRES AUXENDROITS INDIQUÉS SELON
LEFORMATDE CONDUIT UTILISÉ
T SITLETOBE TRANSLATEDIN PANISH
Use this templa te fo r ma rking; do no t a ttempt to cut o ut the ducting hole through it.
NOTE: These cuto uts are cleara nce holes; they do no t need to be the exact size o f ducting.
Utiliser ce ga barit po ur marquer vo s repères; ne pas tenter de découper
le trou pour le conduit à tra vers le gaba rit.
NOTE : Les découpes incluent le jeu nécessaire à l’installatio n; elles ne doivent pas
être du fo rma t exa ct des conduits.
Use esta plantilla pa ra crear ma rca dos; no tra te de corta r el
a gujero del conducto a tra vés de la pla ntilla .
NOTA: To be tra nsla ted in Spa nish.
Ele ctrical acce ss ho le ce nte r
A = single blowe r ho o d
B = double blo we r ho o d
Centre du tro u po ur fil
d’alime ntatio n é le ctrique
A = hotte ve ntilate ur s imple
B = hotte ve ntilate ur do uble
To be translate d in Spanish
Ele ctrical acce ss ho le ce nte r
A = single blowe r ho o d
B = double blo we r ho o d
INSTALLATION MANUAL
INSTALLATION
13
FRAMED CABINET
7/64”
X Y
Z
Refer to the marking on the brackets to determine the correct installation side and
orientation.
Mate the corresponding bracket to the cabinet side frame, while placing rear end
of bracket against the wall. Use a pencil to mark 3 holes (there are 6 holes but only
3 are necessary).
Remove the bracket. Using a 7/64” drill bit, drill 3 holes where marked.
Assemble the bracket to the side frame using a Phillips screwdriver and 3 provided
no. 8 x 5/8” wood screws. Repeat for the other side frame.
7 ] Install the proper installation brackets according to the type of cabinet (framed or frameless).
See below.
4 ] Drill a 1/8” dia. pilot hole for house wiring, at location on template. A
5 ] Use a sharp pencil or 1/8” drill bit to mark the locations for the appropriate duct access
holes (16 locations for 7” round duct, or 4 corner locations for rectangular duct). Remove the
template.
6 ] Draw the border for the exhaust ducting by linking its marks (16 for round duct and 4 for
rectangular duct), then cut the opening in the cabinet bottom (vertical exhaust) or in the wall
(horizontal exhaust). Drill the house wiring hole by using a 1½” hole saw centered with the
pilot hole previously made in 4.
INSTALLATION MANUAL
INSTALLATION
14
[ \
7/64”
X
3 X
YZ
Refer to the marking on brackets to determine the correct installation side and orientation.
Align the corresponding bracket to the cabinet side, while placing rear end of bracket
against the wall. Draw a line on the outer edge of the bracket (as shown).
Slide the bracket towards the center of cabinet and align the outside edge of the
bracket with the marked line, keeping the rear end edge leaning on the wall.
Use a pencil to mark 3 holes.
Remove the bracket. Using a 7/64” drill bit, drill 3 holes where marked.
Assemble the bracket to the cabinet bottom using a Phillips screwdriver and 3 provided
countersunk wood screws. Repeat for the other cabinet side.
FRAMELESS CABINET
INSTALLATION MANUAL
INSTALLATION
15
A
C
B
D
Install the Hood (EZ1 Bracket)
1 ] Run house power cable between service panel and hood location.
2 ] There are 2 pairs of recessed holes on each side of the top of the hood (on rear: and , A B
on front and on illustration below); these holes allow the range hood to hang on the C D
brackets (previously installed).
3 ] Temporarily hang the hood on the brackets using its 2 recessed REAR HOLES ( and ). A B
While holding the hood, run the house power cable into the hood through the strain relief
previously installed in step 6 on page 10.
4 ] Unhook the rear holes from the brackets and hang the hood using its 2 recessed FRONT
HOLES ( and ). , attach the power cable to the hood using the C D While holding the hood
strain relief.
5 ] Hang the hood on the brackets using the 2 recessed FRONT HOLES ( and ). C D While
holding the hood, run the house power cable into the hood through the strain relief
previously installed in step 6 on page 10. Attach power cable to the hood.
NOTE: See final installation steps on next page.
HORIZONTAL EXHAUST INSTALLATION ONLY
VERTICAL EXHAUST INSTALLATION AND NON-DUCTED INSTALLATION ONLY
OTE: N The following procedure applies to both framed or frameless cabinet installations.
DUCTED INSTALLATION ONLY
6 ] Connect the ductwork to the hood and use metal foil duct tape to make joints secure and
air-tight. Make sure the damper assembly (or round duct plate) enters the ductwork and
that the damper opens and closes freely.
A
B
INSTALLATION MANUAL
INSTALLATION
16
FRAMED CABINET FRAMELESS CABINET
7 ] For framed cabinet, secure the hood to the EZ1 brackets using 4 no. 8-18 x 1/2” metal screws
(included in parts bag). Insert 2 screws per side, in the slots (as shown in insets on illustration
below).
8 ] For frameless cabinet, secure the hood to the cabinet using 4 no. 8 x 5/8” round head wood
screws (included in parts bag). Insert 2 screws per side, in the slots (as shown in insets on
illustration below).
WOOD
SCREWS
METAL
SCREWS
INSTALLATION MANUAL
INSTALLATION
17
Standard Installation (without EZ1 Brackets)
1 ] Use the proper diagram below for placement of ductwork and electrical cutout in cabinet
or wall. For a non-ducted installation, DO NOT cut a duct access hole, only cut the hole for
electrical wiring.
2 ] Install part-way four (4) ROUND HEAD no. 8 x 5/8” mounting screws into shims/cabinet,
according to the proper diagram above. (Mounting screws are included in parts bag, but wood
shims and shim mounting screws are not included).
VERTICAL DUCT
ACCESS HOLE
1015/ "16
5¼"5¼"
CENTER
LINE
HOOD MOUNTING SCREWS (4)
ELECTRICAL
ACCESS HOLE
(IN BOTTOM CABINET )
WOOD SHIMS
(RECESSED BOTTOM-
CABINETS ONLY)
CABINET FRONT
3/4"
1⅜"
1½"
7³/16"
47/ "16
CABINET
BOTTOM
9⅞" (24" HOOD)
12⅞" (30" HOOD)
15⅞" (36" HOOD)
18⅞" (42" HOOD)
9⅞" (24" HOOD)
12⅞" (30" HOOD)
15⅞" (36" HOOD)
18⅞" (42" HOOD)
3¼" X 10"
VERTICAL DUCTING
CABINET
BOTTOM
CABINET FRONT
HORIZONTAL DUCT
ACCESS HOLE
HOOD
MOUNTING
SCREWS (4)
ELECTRICAL
ACCESS HOLE
(IN WALL)
3⅞"
CENTER
LINE
WOOD SHIMS
(RECESSED CABINETS-BOTTOM ONLY)13/16"
3/16"
5¼" 5¼"
9⅞" (24" )HOOD
12⅞" (30" HOOD)
15⅞" (36" HOOD)
18⅞" (42" HOOD)
9⅞" (24" HOOD)
12⅞" (30" HOOD)
15⅞" (36" HOOD)
18⅞" (42" HOOD)
7³/16"
3¼" X 10"
HORIZONTAL DUCTING
ELECTRICAL
ACCESS HOLE
(IN BOTTOM CABINET )
HOOD MOUNTING SCREWS (4)
4¹¹/ "16 8" DIA.
HOLE
7-IN. ROUND
7-IN. ROUND
7-IN. ROUND
7-IN. ROUND
7-IN. ROUND
DUCT
DUCT
DUCT
DUCT
DUCT
ACCESS
ACCESS
ACCESS
ACCESS
ACCESS
HOLE
HOLE
HOLE
HOLE
HOLE
7-IN. ROUND
DUCT
ACCESS
HOLE
WOOD SHIMS
(RECESSED BOTTOM-
CABINETS ONLY)
9⅞" (24" HOOD)
12⅞" (30" HOOD)
15⅞" (36" HOOD)
18⅞" (42" HOOD)
9⅞" (24" HOOD)
12⅞" (30" HOOD)
15⅞" (36" HOOD)
18⅞" (42" HOOD)
1015/ "16
1½"
1⅜"
7³/16"
7-IN. ROUND
VERTICAL DUCTING
INSTALLATION MANUAL
INSTALLATION
18
Install the Hood (Standard Installation)
1 ] Run house power cable between service panel and hood location. Run the house power
cable into the hood through the strain relief previously installed in step 6 on page 10.
2 ] Hang hood from (4) mounting screws previously installed. Slide hood back towards wall until
mounting screw heads are engaged in narrow end of keyhole slots in top of hood. Tighten
screws securely. Attach power cable to the hood using the strain relief.
3 ] Connect ductwork to hood and use metal foil duct tape to make joints secure and air-tight.
Make sure the damper assembly (or round duct plate) enters the ductwork and that the damper
opens and closes freely.
DUCTED INSTALLATION ONLY
INSTALLATION MANUAL
INSTALLATION
19
Connect the Wiring
1 ] Connect House Power Cable to range hood wiring: BLACK to BLACK, WHITE to WHITE and
GREEN or bare wire under GREEN ground screw.
! WARNING
Risk of electric shock. Electrical wiring must be done by qualifi ed
personnel in accordance with all applicable codes and standards.
Before connecting wires, switch power off at service panel and lock
service disconnecting means to prevent power from being switched
on accidentally.
! CAUTION
Ensure both tabs on inner top of hood are engaged in their corresponding slots in
wiring cover. Also, take care not to pinch wires while reinstalling wiring cover.
SCREW
2 ] Reinstall wiring cover and attach it to the hood using its retaining screw.
TABS ON INNER
TOP OF HOOD
ENGAGED IN
WIRING COVER
SLOTS.
MOTOR
GROUND
WIRE
HOUSE
POWER CABLE
GROUND
SCREW
INSTALLATION MANUAL
INSTALLATION
20
Install the Light Bulbs
1 ] Align the bulb leads with the small indentations located on the border of the lamp location on
hood (see inset above), then install the bulbs by placing the bulb leads into their grooves in
the socket.
2 ] Gently push upwards and turn clockwise until secure.
Install two shielded Halogen Bulbs (120 V, 50 W max., MR16 or PAR16 with GU10 base), not
included.
NOTE: The Suction Cup Tool (included with hood) can be used to install and remove light bulbs.
Press suction cup tool on bulb and rotate counterclockwise to remove bulb or clockwise
to install bulb.
! WARNING
Do not touch lamps during or soon after operation. Burns may occur. In order to prevent
the risk of personal injury, only install shielded halogen lamps. Also, never install a cool
beam, a dichroic lamp, a lamp not suitable for use in recessed luminaires or identified for
use in enclosed fixtures.
Install the Filters
Ducted Installation Only:
Re-install grease filters removed in step 2, page 9, under “Prepare the Hood”.
Non-ducted Installation Only:
Purchase two non-ducted filters from your local distributor or retailer (see product specification
label for filter type). Attach the non-ducted filters following instructions packed with the non-
ducted filters.
! CAUTION
Most GU10 LED replacement bulbs commonly found in the market are not designed
for use in a cooking environment and might not perform as advertised. Their usage
with this product is not recommended.
SUCTION
CUP TOOL
BULB LEADS BULB LEAD
GROOVES
(IN SOCKET)
INDENT
INSTALLATION MANUAL
WIRING DIAGRAM
21
G/Y
W
BK
O
R
FAN MOTOR BN
BN/W
G/Y
R (Low)
BK (High)
W
120 V AC
Line
Neutral
Ground
BK BK
Motor Switch
Light Switch
Y (Low)
BL (High)
W
WBK
BK
COLOR CODE
BK
BL
BN
BLACK
BLUE
BROWN
R
W
Y
RED
WHITE
YELLOW
BN/W
G/Y
O
BROWN/WHITE
GREEN/YELLOW
ORANGE
W
1
2
3
4
5
6
1
1
2
2
INSTALLATION MANUAL
SERVICE PARTS
22
BCSD SERIES
R PEPLACEMENT ARTS AND EPAIRS R
In order to ensure your unit remains in good working condition, you must use Broan-NuTone LLC genuine replacement parts only.
Broan-NuTone LLC genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable
certification standards and maintain a high standard of safety. Any third party replacement part used may cause serious damage and
drastically reduce the performance level of your unit, which will result in premature failing. Broan-NuTone LLC recommends to contact a
certified service depot for all replacement parts and repairs.
K EY NO. PART NO . DESCRIPTION
QUANTITY
24"
WHITE
24"
STAINLESS
24"
BLACK
1
S97020029 RECIRCULATION COVER PLATE LACK INCLUDING SCREWS , B ( ) 1
S97020030 RECIRCULATION COVER PLATE HITE INCLUDING SCREWS , W ( ) 1
S97020031 RECIRCULATION COVER PLATE TAINLESS STEEL INCL SCREWS , S ( . ) 1
2 SR680508 7'' ROUND DUCT PLATE INCLUDING SCREWS ( ) 1 1 1
3 S97020534 3¼” X AMPER ASSEMBLY INCLUDING SCREWS 10” D ( ) 1 1 1
4 S97020408 BLOWER INCLUDING SCREWS AND MOTOR ( 4 1 CAPACITOR) 1 1 1
5 S97020407 FANPELLER INCLUDING ITEM ( 6) 1 1 1
6 SR99420635 CLIP FOR FANPELLER 1 1 1
7 S99010430-001 GREASE ILTER PEN ESH F - O M - T B1 ( 2) 1 1 1YPE SET OF
8
S99030355 ROCKER SWITCH HITE SET OF , W ( 2) 1
S99030356 ROCKER SWITCH LACK SET OF , B ( 2) 1
S99030367 ROCKER SWITCH REY SET OF , G ( 2) 1
9 S97020448 WIRE HARNESS 1 1 1
* S98011637 WIRING COVER 1 1 1
*S97020292
PARTS BAG : 4 MINCLUDING ETAL SCREWS NO . 8-18 1/2”, X
6 ROUND HEAD NO X WOOD SCREWS . 8 5/8” ,
6 NO X OUNTERSUNK SCREWS UCTION CUP TOOL. 8 1/2” C , 1 S
111
*S97020465 NON DUCTED ILTER- F - T X ( 2)YPE B SET OF
(NON DUCTED INSTALLATION ONLY- ) 111
*SV05921 SHIELDED HALOGEN BULB 50 W, GU10 2 2 2
*S99527587 NON DUCTED FILTER CLIP KIT INCLUDES CLIPS- ( 4 ) 1 1 1
*S97020470 EASY INSTALL KIT INCLUDING HARDWARE ( ) 1 1 1
* ITEM NOT SHOWN .
INSTALLATION MANUAL
SERVICE PARTS
23
R PEPLACEMENT ARTS AND EPAIRS R
In order to ensure your unit remains in good working condition, you must use Broan-NuTone LLC genuine replacement parts only.
Broan-NuTone LLC genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable
certification standards and maintain a high standard of safety. Any third party replacement part used may cause serious damage and
drastically reduce the performance level of your unit, which will result in premature failing. Broan-NuTone LLC recommends to contact a
certified service depot for all replacement parts and repairs.
K EY
NO.P ART NO. DESCRIPTION
QUANTITY
30"
BISCUIT
30"
WHITE
30"
STAINLESS
30"
BLACK
1
S97020029 RECIRCULATION COVER PLATE LACK INCLUDING SCREWS , B ( ) 1
S97020030 RECIRCULATION COVER PLATE HITE INCLUDING SCREWS , W ( ) 1
S97020031 RECIRCULATION COVER PLATE TAINLESS, S STEEL INCL SCREWS ( . ) 1
S97020471 RECIRCULATION COVER PLATE ISCUIT INCLUDING SCREWS , B ( ) 1
2 SR680508 7'' ROUND DUCT PLATE INCLUDING SCREWS ( ) 1 1 1 1
3 S97020534 3¼” X AMPER ASSEMBLY INCLUDING SCREWS 10” D ( ) 1 1 1 1
4 S97020408 BLOWER INCLUDING SCREWS AND MOTOR ( 4 1 CAPACITOR) 1 1 1 1
5 S97020407 FANPELLER INCLUDING ITEM ( 6) 1 1 1 1
6 SR99420635 CLIP FOR FANPELLER 1 1 1 1
7 S99010430-002 GREASE ILTER PEN ESH F - O M - T C1 ( 2) 1 1 1 1YPE SET OF
8
S99030355 ROCKER SWITCH HITE SET OF , W ( 2) 1
S99030356 ROCKER SWITCH LACK SET OF , B ( 2) 1
S99030357 ROCKER SWITCH ISCUIT SET OF , B ( 2) 1
S99030367 ROCKER SWITCH REY SET OF , G ( 2) 1
9 S97020448 WIRE HARNESS 1 1 1 1
* S98011637 WIRING COVER 1 1 1 1
*S97020292
PARTS BAG : 4 MINCLUDING ETAL SCREWS NO . 8-18 1/2”, X
6 R 5/8” , OUND HEAD NO. 8 X WOOD SCREWS
6 1/2” C , 1 S NO. 8 X OUNTERSUNK SCREWS UCTION CUP TOOL
1 1 1 1
*S97020466 NON DUCTED ILTER- F - T X ( 2)YPE C SET OF
( - NON DUCTED INSTALLATION ONLY ) 1 1 1 1
*SV05921 SHIELDED HALOGEN BULB 50 W, GU10 2 2 2 2
*S99527587 NON DUCTED FILTER CLIP KIT INCLUDES CLIPS- ( 4 ) 1 1 1 1
*S97020470 EASY INSTALL KIT INCLUDING HARDWARE ( ) 1 1 1 1
BCSD SERIES
* I TEM NOT SHOWN.
INSTALLATION MANUAL
SERVICE PARTS
25
R PEPLACEMENT ARTS AND EPAIRS R
In order to ensure your unit remains in good working condition, you must use Broan-NuTone LLC genuine replacement parts only.
Broan-NuTone LLC genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable
certification standards and maintain a high standard of safety. Any third party replacement part used may cause serious damage and
drastically reduce the performance level of your unit, which will result in premature failing. Broan-NuTone LLC recommends to contact a
certified service depot for all replacement parts and repairs.
K EY NO. PART NO . DESCRIPTION
QUANTITY
42"
WHITE
42"
STAINLESS
42"
BLACK
1
S97020029 RECIRCULATION COVER PLATE LACK INCLUDING SCREWS , B ( ) 1
S97020030 RECIRCULATION COVER PLATE HITE INCLUDING SCREWS , W ( ) 1
S97020031 RECIRCULATION COVER PLATE TAINLESS STEEL INCL SCREWS , S ( . ) 1
2 SR680508 7'' ROUND DUCT PLATE INCLUDING SCREWS ( ) 1 1 1
3 S97020534 3¼” X AMPER ASSEMBLY INCLUDING SCREWS 10” D ( ) 1 1 1
4 S97020408 BLOWER INCLUDING SCREWS AND MOTOR ( 4 1 CAPACITOR) 1 1 1
5 S97020407 FANPELLER INCLUDING ITEM ( 6) 1 1 1
6 SR99420635 CLIP FOR FANPELLER 1 1 1
7 S99010430-004 GREASE ILTER PEN ESH F - O M - T E1 ( 2) 1 1 1YPE SET OF
8
S99030355 ROCKER SWITCH HITE SET OF , W ( 2) 1
S99030356 ROCKER SWITCH LACK SET OF , B ( 2) 1
S99030367 ROCKER SWITCH REY SET OF , G ( 2) 1
9 S97020448 WIRE HARNESS 1 1 1
* S98011637 WIRING COVER 1 1 1
*S97020292
PARTS BAG : 4 MINCLUDING ETAL SCREWS NO . 8-18 1/2”, X
6 R 5/8” , OUND HEAD NO. 8 X WOOD SCREWS
6 1/2” C , 1 S NO. 8 X OUNTERSUNK SCREWS UCTION CUP TOOL
1 1 1
*S97020468 NON DUCTED ILTER- F - T X ( 2)YPE E SET OF
( - NON DUCTED INSTALLATION ONLY ) 1 1 1
*SV05921 SHIELDED HALOGEN BULB 50 W, GU10 2 2 2
*S99527587 NON DUCTED FILTER CLIP KIT INCLUDES CLIPS- ( 4 ) 1 1 1
*S97020470 EASY INSTALL KIT INCLUDING HARDWARE ( ) 1 1 1
BCSD SERIES
* I TEM NOT SHOWN.
INSTALLATION MANUAL
WARRANTY
26
Limited Warranty
Warranty Period and Exclusions: Broan-NuTone LLC (the “Company”) warrants to the original consumer purchaser of
its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship for
a period of one (1) year from the date of original purchase (or such longer period as may be required by applicable law).
The limited warranty period for any replacement parts provided by the Company and for any Products repaired or replaced
under this limited warranty shall be the remainder of the original warranty period (or such longer period as may be required
by applicable law).
This warranty does not cover fluorescent lamp starters, tubes, halogen and incandescent bulbs, fuses, filters, ducts, roof
caps, wall caps and other accessories for ducting that may be purchased separately and installed with the Product. This
warranty also does not cover (a) normal maintenance and service, (b) normal wear and tear, (c) any Products or parts
which have been subject to misuse, abuse, abnormal usage, negligence, accident, improper or insufficient maintenance,
storage or repair (other than repair by the Company), (d) damage caused by faulty installation, or installation or use
contrary to recommendations or instructions, (e) any Product that has been moved from its original point of installation,
(f) damage caused by environmental or natural elements, (g) damage in transit, (h) natural wear of finish, (i) Products
in commercial or nonresidential use, or (j) damage caused by fire, flood or other act of God or (k) Products with altered,
defaced or removed serial numbers. This warranty covers only Products sold to original consumers in the United States by
the Company or its U.S. distributors authorized by the Company.
This warranty supersedes all prior warranties and, subject to applicable law, is not transferable from the original consumer purchaser.
No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective
products. The foregoing warranties are exclusive and in lieu of any other warranties and conditions, express or implied. THE
COMPANY DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES AND CONDITIONS, AND DISCLAIMS
AND EXCLUDES ALL WARRANTIES AND CONDITIONS IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent that applicable law
prohibits the exclusion of implied warranties or conditions, the duration of any applicable implied warranty or condition is
limited to the period specified for the express warranty above. Some jurisdictions do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you. Any oral or written description of the Product is for the
sole purpose of identifying it and shall not be construed as an express warranty.
Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and valid
under applicable law, but if any provision is held to be prohibited or invalid, such provision shall be ineffective only to the
extent of such prohibition or invalidity, without invalidating the remainder of such provision or the other remaining provisions
of the Limited Warranty.
Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or
repair or replace, without charge, any Product or part thereof, to the extent the Company finds it to be covered by and in
breach of this limited warranty under normal use and service. The Company will ship the repaired or replaced Product or
replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation and shipping, insurance or
other freight charges incurred in the shipment of the Product or part to the Company. If you must send the Product or part to
the Company, as instructed by the Company, you must properly pack the Product or part—the Company is not responsible
for damage in transit. The Company reserves the right to utilize reconditioned, refurbished, repaired or remanufactured
Products or parts in the warranty repair or replacement process. Such Products and parts will be comparable in function
and performance to an original Product or part and warranted for the remainder of the original warranty period (or such
longer period as may be required by applicable law).
Company reserves the right, in its sole discretion, to refund the money actually paid by you for the Product in lieu of repair or
replacement. If the Product or component is no longer available, replacement may be made with a similar product of equal
or greater value, at Company’s sole discretion. This is your sole and exclusive remedy for breach of this limited warranty.
Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR,
REPLACE OR REFUND, AT THE COMPANY’S OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER
THIS LIMITED WARRANTY AND THE COMPANY’S SOLE AND EXCLUSIVE OBLIGATION. THE COMPANY SHALL
NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN
CONNECTION WITH THE PRODUCT, ITS USE OR PERFORMANCE. Incidental damages include but are not limited to
such damages as loss of time and loss of use. Consequential damages include but are not limited to the cost of repairing
or replacing other property which was damaged if the Product does not work properly.
THE COMPANY SHALL NOT BE LIABLE TO YOU, OR TO ANYONE CLAIMING UNDER YOU, FOR ANY OTHER
OBLIGATIONS OR LIABILITIES, INCLUDING, BUT NOT LIMITED TO, OBLIGATIONS OR LIABILITIES ARISING
OUT OF BREACH OF CONTRACT OR WARRANTY, NEGLIGENCE OR OTHER TORT OR ANY THEORY OF STRICT
LIABILITY, WITH RESPECT TO THE PRODUCT OR THE COMPANY’S ACTS OR OMISSIONS OR OTHERWISE.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which
vary from jurisdiction to jurisdiction. The disclaimers, exclusions, and limitations of liability under this warranty will not apply
to the extent prohibited by applicable law.
This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and
does not include the cost of field service travel and living expenses.
Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited warranty
will not constitute a waiver of such terms, limitations or exclusions, nor will such assistance extend or revive the warranty.
The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product,
except for those incurred with the Company’s prior written permission.
How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or
telephone number stated below within seven (7) days of discovering the covered defect, (b) give the model number and part
identification and (c) describe the nature of any defect in the Product or part. At the time of requesting warranty service, you
must present evidence of the original purchase date. If you cannot provide a copy of the original written limited warranty,
then the terms of the Company’s most current written limited warranty for your particular product will control. The most
current limited written warranties for the Company’s products can be found at www.broan.com.
Broan-NuTone LLC 926 West State Street, Hartford, WI 53027 www.broan.com 800-637-1453

Especificaciones del producto

Marca: Broan
Categoría: campana extractora
Modelo: BCSD124SS

¿Necesitas ayuda?

Si necesitas ayuda con Broan BCSD124SS haz una pregunta a continuación y otros usuarios te responderán


campana extractora Broan Manuales

Broan

Broan BKDB136WW Manual de Usario

27 Octubre 2024
Broan

Broan Elite RMIP45 Manual de Usario

14 Septiembre 2024
Broan

Broan Elite 619004 Manual de Usario

14 Septiembre 2024
Broan

Broan BWS1304SS Manual de Usario

14 Septiembre 2024
Broan

Broan EWS1306BLS Manual de Usario

14 Septiembre 2024
Broan

Broan BWP1304SS Manual de Usario

14 Septiembre 2024
Broan

Broan PM250 Manual de Usario

14 Septiembre 2024
Broan

Broan Elite 614804EX Manual de Usario

14 Septiembre 2024
Broan

Broan BWP1364SS Manual de Usario

14 Septiembre 2024
Broan

Broan Elite EW5830SS Manual de Usario

14 Septiembre 2024

campana extractora Manuales

Últimos campana extractora Manuales

Neff

Neff D61MAC1X0B Manual de Usario

27 Octubre 2024
Klarstein

Klarstein 10033709 Manual de Usario

27 Octubre 2024
Halifax

Halifax FTHI740K Manual de Usario

27 Octubre 2024
Hoover

Hoover HDTI6500/1X Manual de Usario

27 Octubre 2024
Heinner

Heinner HTCH-440FS Manual de Usario

27 Octubre 2024
ATAG

ATAG WG411V Manual de Usario

27 Octubre 2024
XO

XO R30SC Manual de Usario

25 Octubre 2024
IKEA

IKEA DATID HW570 Manual de Usario

24 Octubre 2024
Candy

Candy CDG6MB Manual de Usario

24 Octubre 2024
Miele

Miele da 219 1 Manual de Usario

24 Octubre 2024