Byron BY202 Manual de Usario

Byron Timbre de la puerta BY202

Lee a continuación 📖 el manual en español para Byron BY202 (2 páginas) en la categoría Timbre de la puerta. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

™Plug-in

Wire Free Chime Kit

BY202

1: Push Button 5: Plug-in Chime

2: Melody Selector 6: Speaker

3: Bell Push Battery 7: Volume control

4: Signal Sent LED

1: Place a small flat screwdriver

into the locking clip on the

base of the Bell Push.

2: Gently twist.

3: The backing plate will unclip.

To select the Chime Volume level, press the ‘VOL’

button on the chime There are 4 selectable volume

levels, the Door Chime is pre-set to the loudest

volume setting.

Volume

Default

Functions:

6 Selectable Melodies

1: Tubular 3-Note 4: Solo

2: Big Ben 5: Tubular Score

3: Tubular 2-Note 6: Clarinet

Beep

To select a melody for the Door Chime

1: Remove the Back Plate from the Bell

Push.

2: Press the Melody Select button.

3:The chime will play the newly selected

sound.

4: Press again to select the next melody.

Note: For Front/Back door setup, select a

different melody in one of the Bell Pushes.

CR2032

1: plug Chime into a UK 3pin

socket, 220 – 240V ~ 50Hz.

2: Switch the socket on.

3: Chime will ‘Beep’ on Start up.

1: Press and hold the ‘VOL’

button on the Door Chime,

until the Chime goes

‘Beep Beep’ (6 Seconds).

2: Press the Bell Push within

60 seconds to learn the

Bell Push to the chime.

3: The Chime will ring to

confirm setup.

Note: Maximum of 6 Bell

Pushes can be learnt to a

single Chime.

New Chime

Additional Chime

To add an additional Chime unit to the Door Chime kit

1: Press and hold the ‘VOL’ button on your New Door Chime, until the

Chime goes ‘Beep Beep’ (6 Seconds)

2: Press the Bell Push within 60 seconds to learn the additional

Chime to the Bell Push.

3: Chime will ring to confirm setup, wait 60 seconds for the Chime to

exit the learn mode before repressing the bell push.

Additional Bell Push

To add an additional Bell Push to the Door

Chime kit.

1: Press and hold the ‘VOL’ button on your

Door Chime, until the Chime goes

‘Beep Beep’ (6 Seconds).

2: Press the Bell Push within 60 seconds

to learn the additional Bell Push to the

Chime.

3: Chime will ring to confirm setup, wait 60 seconds for the Chime

to exit the learn mode before repressing the bell push.

For Front/back door setup, select a different melody in one of

the Bell Pushes - See Melody Selection.

Note: Maximum of 6 Bell Pushes can be learnt to a single Chime

Adding Additional Chime/Bell Push:

Beep

Front Door

Back Door

1: Insert CR2032 battery

(Supplied) into the battery

holder.

2: Make sure the positive side

is facing upwards.

3: Replace back plate.

Warning: Make sure that the batteries are

replaced correctly to avoid battery failure.

Only replace with same or equivalent type.

Installation Guide: Bell Push

Installation Guide: Chime

Range Guide

User Hints:

In case of the door chime does not sound, please check the

followings:

a) Flat batteries in either Push Button or Door Chime.

b) Wrong battery polarity in either Push Button or Door Chime.

c) For Plug-in Door Chimes make sure the socket is switched on.

d) Bell Push and Door Chime are not paired together, see setup

guide.

e) Materials in between the Bell Push & Chime will reduce the

operating range, move the Door Chime closer to the Bell Push

f) Wire free devices can be affected by external sources e.g. wire

free home alarms or power transformers/adapter

Plug-in Door Chime: BY202

Power: 220 - 240V 50Hz

Range: 100 Metres

Indoor Use Only

Bell Push: BYT

Power: 1 x CR2032 3V DC Battery

(Included)

IP44 Weather Resistant

Type R2 Device - device where the sound output is created by the initial operation

of the control and where the period of sound output continues for the

designed duration irrespective of condition of the control.

IMPORTANT: There are no serviceable parts, do not repair.

Specification

433.92MHz

R&TTE

APPROVED

CH Byron Electrical United Kingdom. www.chbyron.com

FIN

IRL

EST

SLO

Project Manager

Mr G Hunter

GB: CH Byron

Byron House, Sherwood Rd

Astonfields, Bromsgrove

B60 3DR

support@chbyron.com

9-5 Mon-Fri, Local call charges apply

V1.0

Tel: 0845 2301231 (UK)

www.chbyron.com

433.92MHz

R&TTE

APPROVED

CH Byron Electrical United Kingdom. www.chbyron.com

FIN

IRL

EST

SLO

Project Manager

Mr G Hunter

V1.0

Bell Push: BYT

Power: 1 x CR2032 3V DC Battery

(Included)

IP44 Weather Resistant

Type R2 Device - device where the sound output is created by the initial operation

of the control and where the period of sound output continues for the

designed duration irrespective of condition of the control.

IMPORTANT: There are no serviceable parts, do not repair.

Specification

Range Guide

Place the door Chime within the operating range, transmis-

sion of the wire free signal through

Walls, Doors and Ceilings etc, may reduce the operating

range. Chime unit for INDOOR use only.

Diagram for illustration purposes only

‘CLICK’

1: Using back plate as a

template

2: Making sure UP arrows

points UP.

2: Mark and drill holes.

3: Insert wall plugs and attach

to wall using screws

provided.

4: Clip the Bell Push on to the

back plate making sure the

Bell Push ‘Clicks’ in to

place.

Note: The Bell Push can be

installed using a suitable

double sided adhesive tab or

tape when drilling is not

sutiable.

Installation Guide:

Avoid locating the Bell Push/Chime on or directly near

metallic surfaces as this may reduce the operation

range.

UPVC Door Frames:

When locating the bell push onto a UPVC door, always

check the operating performance before final

installation, internal metal frame may affect

performance.

Note: Try adjusting the location of the Bell Push to the Left/Right or

place on external wall.

Resetting Chime:

Reset Chime unit to factory settings.

1: Press and hold the ‘VOL’ button on your Door Chime,

until the Chime goes ‘Beep Beep’ (6 Seconds)

2: Release the ‘VOL’ button

3: Re-press and hold the ‘VOL’ button on your Door Chime,

until the Chime goes ‘Beep’ (6 Seconds)

4: The Chime is now reset.

Vol

Beep

Vol

Beep

Changing Batteries:

Bell Push:

1: Remove back plate from the

Bell Push.

2: Remove old battery from the

holder.

3: Replace with new ‘CR2032’ 3V

battery.

4: Insert into holder making sure

‘+’ is facing up.

5: Test Chime Kit.

Always dispose of old batteries in an environmentally friendly way.

Especificaciones del producto

Marca:	Byron
Categoría:	Timbre de la puerta
Modelo:	BY202
Color del producto:	Wit
Número de niveles de potencia:	2
Amable:	Ventilator elektrisch verwarmingstoestel
Consumo de energía (en espera):	2000 W
Termostato ajustable:	Ja
voltaje-de-entrada-de-CA:	220 - 240 V
Ruedas:	Nee
Tipo de control del termostato:	Mechanisch