Byron SX-209 Manual de Usario

Lee a continuación 📖 el manual en español para Byron SX-209 (2 páginas) en la categoría Timbre de la puerta. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
Door Chime Unit
Inserting the chimes batteries
Slide open the battery compartment door. Insert 2 x 1.5 volt alkaline
batteries (“C”, UM2 & R14 - included) into the battery compartment,
ensuring the battery polarity matches the internal markings. It will beep
twice to indicate that it is ready for the new operation code registration
(Please see Digital Code Set Up). Close the battery compartment.
Wire Free Door Chime Kit SX-209
Model No. SX-209
CR2032
“C”
LR14
“C”
LR14
100m
100m
Operating
Distance
Door Chime Unit Push Button Unit
Remove the locking screw from the
battery fastener. Insert 1 x 3 volt
CR2032 Lithium batteries (Byron
SX100) in the battery compartment,
ensuring the battery polarity
matches the internal markings, then
tighten the screw on the battery
fastener to hold the batteries
firmly in their compartment.
No wiring is required for this Wire Free Door Chime Kit. When the Push Button is pressed, it sends a wire free
signal to the door chime unit that activates the chime. As the operating range is up to 100 metres (320 ft.
approx. - in open field), you can mount or take the door chime virtually anywhere in the home. However, the
transmission range of the wire free signal will be reduced if the signal is transmitted through a number of walls
or ceilings. Metal, and UPVC doorframes will also reduce the operating range.
Push Button Unit
Remove the back of the case by
pushing in the tab on the bottom
with a small, flat screw driver.
Using the two holes on the back of
the Push Button as a template,
mark the fixing position for the unit.
Drill holes and fit wall plugs and
secure the Push Button unit with
screws (self-tapping N3 x 16mm
screw).
Wire Free Batteries
Required
Batteries
Included
Operating
Distance
Loudness
Open Field
1 x 3 volt Lithium batteries (CR2032) have already been installed. Your Push Button is ready to use.
To change
the battery
80db
Push
Button
This
way
up
Operation
Indicator
To mount
Flashing LED Light
Push Button
Melody Selector
Additional Byron “SX” range products can be purchased for compatibility. (except SX-4 and SX-41)
5) Piano
6) Harmony
1) Electro Mechanical - Ding Dong
2) Westminster - 8 notes
3) Jive
4) Wedding March
7) Dog Barking
8) Ringer
The Melody Selector is located inside the push button unit. It is a small button on the top left corner of the
battery compartment marked with “S”. Press the switch once, the melody will change to the next one on the list,
there are a total of 8 melodies for selection. The Push Button is pre-set to “Electro Mechanical - Ding Dong”
therefore, if no change is required, it should not be adjusted.
Melody Selection
C
R
2
0
3
2
C
R
2
0
3
2
Battery
Compartment
Melody
1. Do not mount either unit close to fireplace or expose to high temperatures.
2. Do not expose the Door Chime unit to direct sunlight or moisture.
3. Make sure that no naked flame sources, such as lighted candles, are placed on the unit.
4. The unit should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,
shall be placed on the unit.
5. Replace only with the same or equivalent type of battery that is recommended by the manufacturer.CAUTION:
6. Danger of explosion if battery is incorrectly installed or replaced.CAUTION:
7. This product is not suitable for people who suffer from epilepsy due to flashing light.CAUTION:
Model No. SX-209
Important
R TTE&
approved
Press the button on the Push Button unit once, it sends a wireless
signal to the Door Chime and will activate one of the following
functions:
a) The Door chime will sound as well as the Sound and Light:
Super Bright Light flashing to
maximize attention.
b) The Super bright Light on the Door Chime Light Only:
unit will flash.
c) Door Chime unit will sound.Sound Only:
The function selector is located at the back of the unit, press the
buttons to select the function to operate the chime unit
accordingly. For repeat sound, press the button again. Holding the
button in will repeat the sound.NOT
Door Chime Operation
It is located at the side of the item, slide the switch to adjust the light function as follows:
a) Sound Only
b) Strobe Light Only
c) Sound + Strobe Light
It is located at the back of item, press the button to adjust the sound volume goes up and down. There is a total
of 8 different sound volume levels set, 1=mute and 8 =max level, the door chime will start operating at sound
level 6 initially.
Volume
Control
The unit comes from the factory on a pre-set radio frequency digital
code. However, should your door chime activate intermittently for no
reason at all, it is possible that a similar unit is operating nearby on the
same frequency digital code. The encoded frequency of the Push Button
(transmitter) can be changed to avoid this problem. The Door Chime
unit is equipped with an advanced self-learning operation code ability
therefore no setting is needed.
Digital Code Set Up
1. Remove the back of the case from the Bell Push unit.
2. There are 4-position dipswitch marked 1,2,3 & 4. Use an screwdriver
to alter the dipswitch levers to the “On/Off” position, which can be
altered to achieve a total of sixteen (16) possible digital codes.
3. Select any combination on the Push Button. Press the Push Button,
the Door Chime unit will sound to indicate that new operation code
is registerd and memorized, and it will only work with it.
4. To re-set the operation code, simply remove the batteries from the Door Chime unit and rest for 30 seconds,
it will erase the memory. Re-insert the batteries into the Door Chime unit, it will give 2-beeps to indicate that
it is ready for new code registration. Press the Push Button to confirm the new code is working.
5. Test to ensure correct operation before final installation.
Push Button
Eg.
A. Push Button unit
Power
Consumption
: 1 x 3 volt Lithium battery (CR2032 - included)
: 7.0mA - ON
0.003mA - OFF
B. Door Chime unit
Power
Consumption
Operating Temperature
Operating Distance
Selectable Tone
Selectable Digital Code
: 2 x 1.5 volt alkaline batteries (“C”, UM2 & R14 - included)
: Sound Only-200mA, Strobe Light Only-200mA, Sound+Light-350mA / 0.3mA-Stand By
: -10C to +40C
: 100 metres (320 feet approx.) in open field
: Total eight (8) tones available
: Total sixteen (16) possible digital codes
Problem
Chime does not
sound but LED lights
on Push Button
Chime does not
sound plus no lights
on Push Button LED
Chime sounds
without Push Button
being pressed
Possible Causes
1. Units is out of range (max. range 100M)
2. Push Button and Chime units are not on
same digital code
1. Flat Push Button battery
2. Wrong polarity of battery in Push Button
A similar Wire Free Door Chime product is
operating nearby on the same frequency
digital code
Suggested Remedy
1. Operate the Chime unit within the
operation range (100M)
2. Re-set the digital code
(see Digital Code Set Up)
1. Change the battery
2. Re-insert battery as internal marking
in right polarity
Change the digital code
(see Digital Code Set Up)
Important: There are no serviceable parts in the unit, do not attempt to repair it.
Trouble Shooting & User Hints
Specification
Type R2 Device - device where the sound output is created by the initial operation of the control and where the
period of sound output continues for designed duration irrespective of condition of the control.
• Sound
• Strobe Light
• Sound +
Strobe Light
Light Option Control Button
Sound Volume Control Button

Especificaciones del producto

Marca: Byron
Categoría: Timbre de la puerta
Modelo: SX-209

¿Necesitas ayuda?

Si necesitas ayuda con Byron SX-209 haz una pregunta a continuación y otros usuarios te responderán




Timbre de la puerta Byron Manuales

Timbre de la puerta Manuales

Últimos Timbre de la puerta Manuales