Café CHS950P2MS1 Manual de Usario
Lee a continuación 📖 el manual en español para Café CHS950P2MS1 (8 páginas) en la categoría horno. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/8
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT — Save these
instructions for local inspector’s use.
• IMPORTANT — Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with consumer.
• Note to consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance
requires a qualified installer or electrician.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation is
not covered under warranty.
FOR YOUR SAFETY:
If you did not receive an anti-tip bracket with your purchase,
visit ).cafeappliances.com (In Canada, cafeappliances.ca
Installation Instructions
Electric Slide-In Ranges
MATERIALS YOU MAY NEED TOOLS YOU WILL NEED
(UL Listed 40 AMP)
4-Wire Cord 4’ long OR
3-Wire Cord 4’ long
Squeeze Connector
(For Conduit
Installations Only)
1 REMOVE PACKAGING MATERIALS: Failure to remove packaging
materials could result in damage to the appliance. Remove all packing parts from oven,
racks, heating elements and drawer. Also, remove protective film and labels on the outer
door, cooktop and control panel.
Drill with 1/8” Bit
Safety Glasses
Adjustable Wrench
Level
Tin Snips
Tape Measure
Pliers
1/4” Nut Driver
Questions? Visit cafeappliances.com. In Canada, visit cafeappliances.ca.
2 PREPARE THE OPENING (FOR INDOOR USE ONLY)
See illustrations for all rough-in and spacing dimensions. The range may be placed with 0”
clearance (flush) at the back wall and side walls of the cabinet.
NOTE: Use a 4’ power cord to prevent interference with
the storage drawer. Power cords 4
1»2’ to 6’ long may
have to be dressed to allow for proper drawer closing.
MINIMUM DIMENSIONS BETWEEN COOKTOP,
WALLS AND ABOVE THE COOKTOP:
A. Make sure the wall covering, countertop, flooring
and cabinets around the range can withstand the
heat (up to 200°F) generated by the range. 0” to
cabinets below cooktop and at the range back.
B. Allow 30” minimum clearance between surface units
and bottom of unprotected wood or metal cabinet, or
allow a 24” minimum when bottom of wood or metal
cabinet is protected by no less than 1/4” thick flame
retardant millboard covered with not less than No.
28 MSG sheet metal, (.015”), .015” thick stainless
steel, .024” aluminum or .020” copper.
C. This appliance has been approved for 0” spacing to
adjacent surfaces above the cooktop. However, a 6” minimum spacing to surfaces less than 15”
above the cooktop and adjacent cabinet is recommended to reduce exposure to steam, grease
splatter and heat.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space
above the cooktop should be avoided. If cabinet storage space is to be provided above the cooktop,
the risk can be reduced by installing a range hood that projects at least 5” beyond the front of the
cabinets. Cabinets installed above the cooktop must be no deeper than 16”.
Anti-Tip Bracket
Kit Included
WARNING Before
beginning the installation, switch power
off at service panel and lock the service
disconnecting means to prevent power
from being switched on accidentally.
When the service disconnecting means
cannot be locked, securely fasten a
prominent warning device, such as a
tag, to the service panel.
• A child or adult can tip the range and be killed.
• Install the anti-tip bracket to the wall or floor.
• Engage the range to the anti-tip bracket by sliding the
range back such that the foot is engaged.
• Re-engage the anti-tip bracket if the range is moved.
• Failure to do so can result in death or serious burns
to children or adults.
Tip-Over Hazard
WARNING
A
C
B
A
C
Both
Sides
30”
Install the
outlet box
on either
side of the C
L
36
1»4” ± 1»4”
11»8”
437»8”
267»8”
w/o handle
29 1»2”
with handle
30”
3”
3” 3”
9” 8”
4”
71»2”21»4”
21»4”
Recommended
acceptable
electrical outlet
area. Orient the
electrical receptacle
so the length is
parallel to the floor.
3 ELECTRICAL REQUIREMENTS
WARNING This appliance must be properly grounded.
WARNING
All new constructions, mobile homes, recreational vehicles and installations
where local codes do not allow grounding through neutral, require a 4-conductor UL-listed range cord.
WARNING To prevent fire or shock, do not use an extension cord with this appliance.
WARNING To prevent shock, remove house fuse or open circuit breaker before
beginning installation.
We recommend you have the electrical wiring and hookup of your range connected by a qualified
electrician. After installation, have the electrician show you how to disconnect power from the range.
You must use a single-phase, 120/208 VAC or 120/240 VAC, 60 hertz electrical system. If you
connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring
must be used.
Effective January 1, 1996, the National Electrical Code requires that new construction (not existing)
utilize a 4-conductor connection to an electric range. When installing an electric range in new
construction, mobile home, recreational vehicle, or an area where local codes prohibit grounding
through the neutral conductor, refer to the section on four-conductor branch circuit connections.
Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven
according to governing codes could result in a hazardous condition. If there are no local codes,
your oven must be wired and fused to meet the National Electrical Code, NFPA No. 70 – latest
edition, available from the National Fire Protection Association.
This appliance must be supplied with the proper voltage and frequency, and connected to an
individual, properly grounded, 40 amp (minimum) branch circuit protected by a circuit breaker or
time-delay fuse.
Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be provided with
ring terminals on wire and a strain relief device.
A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range cord
is not recommended but if used, it should be marked for use with nominal 1
3»8” diameter connection
openings. Care should be taken to center the cable and strain relief within the knockout hole to
keep the edge from damaging the cable.
The rating plate is located on the oven frame or on the side of the drawer frame.
NOTE: Use of automatic, wireless or wired external switches that shut off power to the appliances,
are not recommended for this product.
4 POWER CORD AND CONDUIT INSTALLATION
A Remove wire cover (on the back of range) by removing screws using a 1/4” nut driver. You
can access the terminal block by either removing a terminal block cover (on some models) or
the wire cover. Do not discard these screws.
B For power cord and 1” conduit only, remove
the knockout ring (13»8”) located on bracket
directly below the terminal block. To remove
the knockout, use a pair of pliers to bend the
knockout ring away from the bracket and
twist until ring is removed.
D For 3/4” conduit installations only, purchase a squeeze connector matching the diameter
of your conduit and assemble it in the hole. Insert the conduit through the squeeze connector
and tighten. Allow enough slack to easily attach the wires to the terminal block. NOTE: Do
not install the conduit without a squeeze connector. The squeeze connector MUST be
installed before reinstalling the rear terminal block.
Knockout
ring in
bracket
Knockout ring
removed
Terminal block
(appearance
may vary)
C For power cord installations only (see
the next step if using conduit), assemble
the strain relief in the hole. Insert the
power cord through the strain relief and
tighten. Allow enough slack to easily
attach the cord terminals to the terminal
block. If tabs are present at the end of
the winged strain relief, they can be
removed for better fit.
NOTE: Do not install the power cord
without a strain relief. The strain relief
bracket MUST be installed before
reinstalling the rear range wiring cover.
Power cord
Strain relief
Terminal
block
Bracket
Squeeze
connector Terminal block
Conduit Bracket
Proceed to step 6 or 7.
Rating plate
DOUBLE OVEN
Rear of Range
Screws to
Remove
Terminal
Block
Terminal
Block
Cover
6 3-WIRE INSTALLATION (GROUND IS THROUGH THE
NEUTRAL WIRE)
WARNING Shock Hazard
The neutral wire and ground strap must be
connected as shown below for the range to be
properly grounded. Do not remove the ground strap.
Failure follow this instruction may result in potential
shock hazard.
WARNING Fire hazard
Terminal block screws must be securely tightened.
Failure to do so may result in potential fire hazard.
FOR POWER CORD INSTALLATION
A. Remove the 3 lower screws from the terminal
block. Do not loosen the upper screws.
B. Do not cut or remove the ground strap.
C. Insert the 3 screws through each power cord
terminal ring and back into the terminal block. Be
certain the white wire is in the center. Securely
tighten each screw (35 to 50 in-lbs.)
FOR CONDUIT INSTALLATION
A. Loosen the 3 lower screws on the terminal block. Do
not loosen the upper screws.
B. Do not cut or remove the ground strap.
C. Insert the bare wire tip (insulation stripped 5/8”) into the
bottom terminal block openings. Be certain the white
wire is in the center. On certain models, the wire must
be inserted through an opening in the ground strap.
Securely tighten each screw onto each wire (35 to 50
in-lbs.).
D. Reinstall terminal block cover.
NOTE: Aluminum building wire may be used but it must
be rated for the correct amperage and voltage.
PROCEED TO STEP 8.
7 4-WIRE INSTALLATION (SEPARATE GROUND WIRE)
WARNING The neutral wire of
the supply circuit must be connected to the
neutral terminal located in the lower center
of the terminal block. The power leads must
be connected to the lower left and the lower
right terminals of the terminal block. The
grounding lead must be connected to the
frame of the range with the ground plate and
the green ground screw.
FOR POWER CORD INSTALLATION
A. Remove the 3 lower screws from the
terminal block. Do not loosen the upper
screws.
B. Remove the ground screw and ground plate
and retain them.
C. Cut the ground strap below the terminal
block and discard the lower section.
D. Insert the ground screw through the ground
plate (removed earlier) and back into the
range frame. Tighten securely, but do not
over-tighten (15 to 20 in-lbs.)
E. Insert the 3 terminal screws through each
power cord terminal ring and back into the
terminal block. Be certain the white wire is
in the center. Securely tighten each screw
(35 to 50 in-lbs.
F. Reinstall terminal block cover.
FOR CONDUIT INSTALLATION
A. Remove the 3 lower screws from the terminal
block. Do not loosen the upper screws.
B. Remove the ground screw and ground plate
and retain them.
C. Cut the ground strap below the terminal block
and discard the lower section.
D. Insert the bare ground bare wire tip (insulation
stripped 5/8”) between the range frame and the
ground plate (removed earlier) and secure it in
place with the ground screw. Tighten securely,
but do not over-tighten (15 to 20 in-lbs).
E. Insert the wire tips (insulation stripped 5/8”) into
the bottom terminal block openings. Be certain
the white wire is in the center. On certain
models, the wire must be inserted through an
opening in the ground strap. Securely tighten
each screw onto each wire (35 to 50 in-lbs.)
F. Reinstall terminal block cover.
NOTE: Aluminum building wire may be used but it must be rated for the correct amperage and voltage.
Ground
strap
Terminal block
(appearance
may vary)
Neutral
terminal
Power cord
Ground
plate
Power Cord
Red or
Black
Red or
Black
White
Terminal
block
Red or
Black
Red or
Black
Neutral
terminal
Ground plate
(grounding to
range)
Ground
screw
After–Power Cord
Green
or Bare
White
Before–Power Cord and Conduit
Terminal
block
Neutral
terminal
Ground
strap
Ground strap
or
After–Conduit
Terminal
block Ground plate
(grounding to
range)
Wire
tips
Ground
screw
Red or
Black
Red or
Black
White
Green
or Bare
Wire
tips
Terminal
block
Conduit
Conduit
Red or
Black Red or
Black
White
5 REAR TRIM INSTALLATION
For all installations, install the required rear trim to back of range with 4 screws provided.
Screws
Rear Trim
Back of
Range
Especificaciones del producto
| Marca: | Café |
| Categoría: | horno |
| Modelo: | CHS950P2MS1 |
¿Necesitas ayuda?
Si necesitas ayuda con Café CHS950P2MS1 haz una pregunta a continuación y otros usuarios te responderán
horno Café Manuales
17 Octubre 2024
17 Octubre 2024
17 Octubre 2024
17 Octubre 2024
17 Octubre 2024
17 Octubre 2024
17 Octubre 2024
17 Octubre 2024
12 Octubre 2024
19 Septiembre 2024
horno Manuales
- horno Candy
- horno Electrolux
- horno Samsung
- horno ATAG
- horno LG
- horno Bosch
- horno AEG
- horno IKEA
- horno Philips
- horno Panasonic
- horno Bauknecht
- horno BEKO
- horno Delonghi
- horno Etna
- horno Grundig
- horno Indesit
- horno Inventum
- horno Kenwood
- horno Krups
- horno Liebherr
- horno Miele
- horno Medion
- horno Quigg
- horno Siemens
- horno Unold
- horno Whirlpool
- horno Zanussi
- horno Tefal
- horno Zanker
- horno Acec
- horno Adler
- horno Alpina
- horno Amica
- horno Airlux
- horno Amana
- horno Aga
- horno Ardo
- horno Ariete
- horno Arcelik
- horno Asko
- horno Aroma
- horno Silverline
- horno Bartscher
- horno Morphy Richards
- horno Eurom
- horno GE
- horno Orbegozo
- horno Salton
- horno Princess
- horno Sharp
- horno Techwood
- horno Fisher And Paykel
- horno Bertazzoni
- horno Lamona
- horno Klarstein
- horno Fagor
- horno Brandt
- horno Omega
- horno Severin
- horno Smeg
- horno Telefunken
- horno Gorenje
- horno Neff
- horno Silvercrest
- horno Baumatic
- horno Nedis
- horno Thomson
- horno Arthur Martin
- horno Korona
- horno Hoover
- horno Saturn
- horno Black And Decker
- horno Breville
- horno KitchenAid
- horno Innoliving
- horno Tristar
- horno Domo
- horno Teka
- horno Trisa
- horno Progress
- horno Cata
- horno Gaggenau
- horno Hotpoint-Ariston
- horno Ignis
- horno Waring Commercial
- horno Tomado
- horno Kernau
- horno Maytag
- horno Livoo
- horno Thermador
- horno OK
- horno Hisense
- horno Hyundai
- horno Hanseatic
- horno Vox
- horno Cylinda
- horno Bestron
- horno Bellini
- horno Avanti
- horno Oster
- horno Westinghouse
- horno Vestel
- horno ECG
- horno Moulinex
- horno Sinbo
- horno Izzy
- horno Pelgrim
- horno Blomberg
- horno Bush
- horno Jata
- horno Magic Chef
- horno Swan
- horno Emerio
- horno RCA
- horno Scarlett
- horno Clatronic
- horno Taurus
- horno Russell Hobbs
- horno Elica
- horno Constructa
- horno BlueStar
- horno Summit
- horno Hotpoint
- horno Sencor
- horno Midea
- horno Landmann
- horno De Dietrich
- horno Junker
- horno Cuisinart
- horno Blaupunkt
- horno Mabe
- horno Concept
- horno Gram
- horno Monogram
- horno Frigidaire
- horno Sunbeam
- horno Iberna
- horno Svan
- horno Logik
- horno Danby
- horno Balay
- horno Valberg
- horno Stirling
- horno PKM
- horno Frilec
- horno Rosieres
- horno Scholtes
- horno Profilo
- horno Cramer
- horno KKT Kolbe
- horno Gemini
- horno Thetford
- horno Berg
- horno CDA
- horno Imperial
- horno Hendi
- horno Mellerware
- horno Castor
- horno Heinner
- horno Schneider
- horno Termozeta
- horno Sanyo
- horno Eldom
- horno Kenmore
- horno Philco
- horno Juno
- horno Nabo
- horno Guzzanti
- horno Defy
- horno Infiniton
- horno Mitsubishi
- horno Dometic
- horno Aspes
- horno Dimplex
- horno DCG
- horno Suntec
- horno Blokker
- horno Blanco
- horno Orima
- horno Trebs
- horno First Austria
- horno Nordmende
- horno Husqvarna
- horno Koenic
- horno Falmec
- horno Mach
- horno Haier
- horno Rangemaster
- horno Friac
- horno H.Koenig
- horno Binatone
- horno Boretti
- horno Ariston Thermo
- horno Steba
- horno Viking
- horno Eico
- horno Wolkenstein
- horno Hansa
- horno Drew & Cole
- horno Thor
- horno Kubo
- horno Exquisit
- horno Elba
- horno Proline
- horno Euromaid
- horno Corberó
- horno Crosley
- horno WLA
- horno New Pol
- horno Zelmer
- horno Ardes
- horno Kelvinator
- horno Biltema
- horno Element
- horno SEB
- horno Mora
- horno Everglades
- horno Steel Cucine
- horno Bomann
- horno Hamilton Beach
- horno Novy
- horno Zerowatt
- horno Kuppersbusch
- horno Continental Edison
- horno Jenn-Air
- horno Limit
- horno Freggia
- horno Insignia
- horno Edesa
- horno Ufesa
- horno Rommelsbacher
- horno Leonard
- horno Presto
- horno Kaiser
- horno Lofra
- horno Franke
- horno New World
- horno AYA
- horno Leisure
- horno Camry
- horno Nodor
- horno Bompani
- horno Jocel
- horno Glem Gas
- horno Xblitz
- horno Viva
- horno Respekta
- horno M-System
- horno Koblenz
- horno Proctor Silex
- horno Primo
- horno Barbecook
- horno German Pool
- horno Rex
- horno Creda
- horno Tower
- horno Comfee
- horno Meireles
- horno Dacor
- horno Falcon
- horno Technika
- horno Saro
- horno Navitel
- horno Scandomestic
- horno Airforce
- horno V-Zug
- horno Godrej
- horno Sauber
- horno MPM
- horno Konig
- horno Nextbase
- horno Matrix
- horno Zenith
- horno Becken
- horno Esatto
- horno Belling
- horno Tesla
- horno Char-Broil
- horno Sogo
- horno Mx Onda
- horno Napoleon
- horno Hobart
- horno Essentiel B
- horno Mestic
- horno Team
- horno Privileg
- horno ProfiCook
- horno Vivax
- horno Stoves
- horno Faber
- horno Cosori
- horno Nevir
- horno Ilve
- horno Altus
- horno Campingaz
- horno Coyote
- horno CaterChef
- horno Gys
- horno Parmco
- horno G3 Ferrari
- horno Caple
- horno Eurotech
- horno Cadac
- horno Wolf
- horno Thermex
- horno Bimar
- horno Edilkamin
- horno Vestfrost
- horno Kunft
- horno Cambridge
- horno Caso
- horno Dualit
- horno Outdoorchef
- horno Smev
- horno Upo
- horno Hestan
- horno Rommer
- horno Comelec
- horno ZLine
- horno Heller
- horno Grunkel
- horno Nesco
- horno Unox
- horno Coline
- horno Scancool
- horno Veripart
- horno White And Brown
- horno Home Electric
- horno Bora
- horno Emax
- horno Sauter
- horno Ellrona
- horno Lynx
- horno Barazza
- horno Optimum
- horno Flavel
- horno Furrion
- horno Cecotec
- horno Arctic Cooling
- horno Instant
- horno Micromaxx
- horno Dash
- horno Fratelli Onofri
- horno Ronco
- horno Eurochef
- horno Atlas
- horno Kalorik
- horno Turbotronic
- horno Marynen
- horno Opera
- horno Therma
- horno La Germania
- horno Luxell
- horno Krefft
- horno Westfalia
- horno Oranier
- horno Galanz
- horno Leventi
- horno Tisira
- horno Orava
- horno Rösle
- horno Riviera And Bar
- horno Apelson
- horno Witt
- horno Melchioni
- horno Khind
- horno Foster
- horno Venga
- horno Rival
- horno Eudora
- horno Thomas
- horno Duronic
- horno Wells
- horno Kucht
- horno Kogan
- horno Mibrasa
- horno Bizerba
- horno Signature
- horno Lacanche
- horno Traeger
- horno Sam Cook
- horno Consul
- horno JennAir
- horno LERAN
- horno General Electric
- horno MSR
- horno SPT
- horno Mistral
- horno Pit Boss
- horno Hatco
- horno Elin
- horno Fulgor Milano
- horno High One
- horno WestBend
- horno Linarie
- horno Companion
- horno XO
- horno NU-VU
- horno Curtiss
- horno Blodgett
- horno Nemco
- horno Vedette
- horno K&H
- horno Artusi
- horno Alto-Shaam
- horno TurboChef
- horno Simfer
- horno Rinnai
- horno Firefriend
- horno Merrychef
- horno LAFE
- horno Sirius
- horno Promis
- horno Sôlt
- horno Ravanson
- horno Chef
- horno Create
- horno Girmi
- horno Hiberg
- horno Ferrari
- horno Cosmo
- horno Elements
- horno ARC
- horno Eltac
- horno Kitchenware
- horno Emilia
- horno Roller Grill
- horno DPM
- horno Studio
- horno Sunpentown
- horno Brastemp
- horno Royal Catering
- horno Cookology
- horno Atosa
- horno Vitrokitchen
- horno Brentwood
- horno Euro Appliances
- horno Gasmate
- horno Arthur Martin-Electrolux
- horno Triomph
- horno PITT
- horno Elektra Bregenz
- horno KB Elements
- horno InAlto
- horno TZS First Austria
- horno Electroline
- horno Capital
- horno Porter & Charles
- horno Pyramis
- horno Pando
- horno Classique
- horno Wiggo
- horno Nestor Martin-Electrolux
- horno Kluge
- horno Imarflex
- horno Mayer
- horno Acros
- horno HomeCraft
- horno La Cornue
- horno Master Kitchen
- horno Goldbrunn
- horno Pitsos
- horno Yamazen
Últimos horno Manuales
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024