Chamberlain 041A5021-H-315 Manual de Usario

Chamberlain No categorizado 041A5021-H-315

Lee a continuación 📖 el manual en español para Chamberlain 041A5021-H-315 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
To prevent possible SERIOUS INJURY or DEATH from electrocution,
disconnect power to opener BEFORE proceeding.
To prevent damage to the receiver/logic board, do not touch the printed
circuit board of the replacement receiver/logic board during installation.
REPLACING RECEIVER/LOGIC
PANEL ASSEMBLY
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
This assembly is a replacement for your original receiver/logic
panel assembly. See side two for code programming instructions.
Depending on model type, you may have to remove the light lens
before proceeding with replacement part installation. The receiver/
logic panel assembly is located as shown below with corresponding
garage door opener models. The light lens is removed.
1. Disconnect all wires from the terminal screws of your opener’s
receiver/logic panel assembly, noting color of wires.
2. Remove screws to disengage the assembly from the opener
chassis.
3. Disconnect assembly from opener by holding the wire connector
plug and pulling down on the panel.
4. Install replacement assembly by reversing previous steps.
Connector plug is polarized. Take care to seat it properly and do
not force connection.
5. Re-connect power.
NOTE: A test of the safety reverse system is necessary for safe
operation. Instructions are on page two and in your opener’s manual.
Open and close force settings may also require adjustment. Refer to
your owner’s manual.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
© 2022, The Chamberlain Group LLC.
114-5799-000 All rights reserved
Without a properly installed safety reversal system, persons (particularly
small children) could be SERIOUSLY INJURED or KILLED by a closing
garage door.
• Safety reversal system MUST be tested every month.
• If one control (force or travel limits) is adjusted, the other control may
also need adjustment.
• After ANY adjustments are made, the safety reversal system MUST be
tested. Door MUST reverse on contact with 1-1/2” (3.8 cm) high
object (or 2x4 laid flat) on the floor.
Select a remote control push button to operate the opener.
1. Press and hold the selected remote control push button
2. Then press and release the “SMART” (Learn) button on the opener
panel. The opener light will flash once.
3. Release the remote control push button.
Now the opener will operate when the remote push button is pressed.
NOTE: If you release the remote control push button before the
opener light flashes, the receiver will not learn the code.
Garage Door Opener
(With “Smart” Button)
“Smart” (learn)
Button
Indicator Light
Kg Kg
1 2 3
Select a
push button
Press and hold the “SMART” button on the opener panel until the
indicator light turns off (about 6 seconds). ALL the codes the
opener has learned will be erased.
To reprogram, repeat Steps 1–3 for each remote control in use.
Code programming instructions are also located on the opener
panel.
Conduct the Safety Reverse Test After:
Each adjustment of door arm length, force controls or limit
controls.
Any repair to or adjustment of the garage door (including springs
and hardware).
Any repair to or buckling of the garage floor.
Any repair or adjustment to the opener.
Place a one-inch board (or a 2x4 laid flat) on the floor, centered
under the garage door.
Operate the door in the down direction. The door must reverse on
striking the obstruction.
If the door stops on the obstruction, it is not traveling far enough in
the down direction.
Increase the DOWN limit by turning the DOWN limit adjustment
screw counterclockwise 1/4 turn.
Repeat the test.
NOTE: On a sectional door, make sure limit adjustments do not force
the door arm beyond a straight up and down position.
When the door reverses on the one-inch board, remove the
obstruction and run the opener through 3 or 4 complete travel
cycles to test adjustment.
NOTE: If the door will not reverse after repeated adjustment attempts,
call for professional garage door service.
W
W
W
W
WAR
AR
AR
AR
ARN
N
N
N
NING
ING
ING
ING
ING

Especificaciones del producto

Marca: Chamberlain
Categoría: No categorizado
Modelo: 041A5021-H-315

¿Necesitas ayuda?

Si necesitas ayuda con Chamberlain 041A5021-H-315 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Chamberlain Manuales

No categorizado Manuales

Últimos No categorizado Manuales