Chauvet WELL Com Manual de Usario

Lee a continuación 📖 el manual en español para Chauvet WELL Com (16 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/16
Quick Reference Guide
English EN
Español ES
Français FR
Nederlands NL
1
EN
QUICK REFERENCE GUIDE
WELL COM QRG Rev. 2
About This Guide
The WELL COM Quick Reference Guide (QRG) has basic product information such as connection, mounting, menu
options, and DMX values. Download the User Manual from www.chauvetprofessional.com for more details.
Disclaimer
The information and specifications contained in this QRG are subject to change without notice.
Safety Notes
DO NOT open this product. It contains no user-serviceable parts.
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the
product from power via breaker or by unplugging it.
DO NOT look at the light source when the product is on.
CAUTION: This product’s housing may be hot when lights are operating. Mount this product in a location with
adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
DO NOT leave any flammable material within 50 cm of this product while operating or connected to power.
CAUTION: When transferring product from extreme temperature environments, (e.g., cold truck to warm humid
ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow
product to fully acclimate to the surrounding environment before connecting it to power.
Not for permanent outdoor installation in locations with extreme environmental conditions. This includes, but is not
limited to:
Exposure to a marine/saline environment (within 3 miles of a saltwater body of water).
Where the normal high or low temperatures of the location exceed the temperature ranges in this manual.
Locations that are prone to flooding or being buried in snow.
Other areas where the product will be subject to extreme radiation or caustic substances.
USE a safety cable when mounting this product overhead.
DO NOT operate this product outdoors or in any location where dust, excessive heat, water, or humidity may affect
it. (IP20)
DO NOT operate this product if the housing, lenses, or cables appear damaged.
DO NOT connect this product to a dimmer or rheostat.
ONLY connect this product to a grounded and protected circuit.
ONLY use the hanging/mounting bracket to carry this product.
In the event of a serious operating problem, stop using immediately.
The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at higher temperatures.
Contact
Use the information in Contact Us at the end of this QRG. Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux,
contact your distributor to request support or return a product.
What is Included
WELL COM
External Power Supply
Warranty Card
Quick Reference Guide
AC Power
This product has an external auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
EN
2
WELL COM QRG Rev. 2
QUICK REFERENCE GUIDE
Overview
Setting Up Products with WELL COM
The WELL COM is ready to use straight out of the box.
To configure your products with WELL COM you must perform the following steps:
1. Connect WELL COM to power.
2. Turn on Wi-Fi™ on your mobile device.
3. Go to the Wi-Fi™ settings on your mobile device and connect to WELL COM’s default Wi-Fi™ (SSID) WIFI-
WELL COM. To avoid interference with other wireless signals in the immediate area, manually select the Wi-
Fi™ channel (CH 2 or CH11) on the WELL COM within the app settings.
4. Set your products to receive signal input from WELL COM. For details, refer to the User Manuals for the
products in your setup.
a. Set products to receive signals on the same channel as was set on WELL COM in the previous step.
b. Set products to their most basic DMX personality.
5. Select whether WELL COM receives signals wirelessly or via a DMX cable.
6. Once your products are properly connected to WELL COM, and WELL COM is properly connected to the WELL
COM app, open the WELL COM app on your mobile device.
# Description Function
1 <LINK> Press to reset wireless fixture pairing
2 DMX DMX in port (adapter included)
3 Power Charger
Micro USB B port for charging the battery
External power supply included
Battery Charge Time - 8 hours
Battery Life - 8 hours
4 Wi-fi Pairing Blinks for 5 seconds after pressing <LINK>, and
then intermittently while connected to products
5 DMX Signal Blinking - No DMX signal detected
Solid - DMX signal detected
6 Wi-fi Signal Blinking - No Wi-Fi signal detected
Solid - Wi-Fi signal detected
7 Battery Life
Green - Power is currently 50–100%
Orange - Power is currently 25–50%
Red - Power is currently less than 20%
Blinking - Battery is charging
8 <PWR> Press to power on/off the device
The default password for the WELL COM is 2323.
If you have not already done so, download and install the WELL COM app onto your mobile device.
Make sure the DMX starting address is set to 001.
For DMX products, be sure to use a DMX cable to connect from DMX Out of the product transmitting the
DMX signal to the DMX In of the product receiving the DMX signal. An adapter has been included for this
purpose.
1 2 3 4 5 6 7 8

Especificaciones del producto

Marca: Chauvet
Categoría: No categorizado
Modelo: WELL Com

¿Necesitas ayuda?

Si necesitas ayuda con Chauvet WELL Com haz una pregunta a continuación y otros usuarios te responderán




No categorizado Chauvet Manuales

No categorizado Manuales

Últimos No categorizado Manuales