Chief PLP2000B Manual de Usario

Chief soporte de panel plano PLP2000B

Lee a continuación 📖 el manual en español para Chief PLP2000B (8 páginas) en la categoría soporte de panel plano. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/8
CHIEF MANUFACTURING INC. 8805-000183 Rev F
1-800-582-6480 952-894-6280 FAX 952-894-6918 ©2008 Chief Manufacturing
8401 EAGLE CREEK PARKWAY, STE. 700 www.chiefmfg.com
SAVAGE, MINNESOTA 55378 USA 03/08
I N S T A LL A T I O N IN S T R U C T IO N S
PLP Series Wall Mount
The PLP Series wall mount accommodates large flat
screens weighing up to 200 lbs (90.72kg). The teardrop
holes in the mount allow for quick connect/disconnect of
the screen, thus simplifying installation and maintenance
processes.
The top and bottom mounting brackets are adaptable to
supporting framework with wood studs that are 16” on
center or 24”on center.
The mount has integrated lateral shift, allowing for four
different mounting options. For dual wood studs 16” on
center, the lateral shift is + 4.5 inches. For dual wood
studs 24” on center, the lateral shift is + 0.5 inches.
The display can be pulled and tilted by hand into any
position in the zero-to-15 degree tilt range and remain
stationary.
The bottom of the mount pulls forward 4” from the wall
and locks into place for installation of cable connections.
The mount also uses Chief’s exclusive Q-Latch™
mounting system, which offers quick connect/disconnect
display mounting. The display is secured to the mount
with a latching flag. For additional security, you can lock
the latching flag in place by adding a padlock. PLP Series
Installation Instructions PLP Series
2
! IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval
documents and drawings before beginning installation. OSHPD documents and drawings are available at
www.chiefmfg.com, and located on the product information page for the mount.
BEFORE YOU BEGIN
CAUTION: To prevent damage to your monitor and PLP, which could affect or void the Factory
warranty, thoroughly study all instructions and illustrations before you begin to install the mount. Pay
particular attention to the Warnings and Cautions in this document.
The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the
mount must be capable of supporting five times the total weight of the equipment.
The maximum weight to be installed on the PLP Series wall mount is 200 lbs (90.72kg).
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-
6480.
IMPORTANT WARNINGS and CAUTIONS!
WARNING A WARNING alerts you to the possibility of serious injury or death if you do not
follow the instructions.
CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do
not follow the corresponding instructions.
WARNING Improper installation can result in serious personal injury! Make sure that the
structural members can support a redundant weight factor five times the total weight
of the equipment. If not, reinforce the structure before installing the mount.
WARNING Be aware of the potential for personal injury or damage to the equipment if it is not
installed correctly. Consider the weight of the mount without the display.
WARNING The installer is responsible for verifying that the display to which the wall mount is
fastened will safely support the combined load of all attached components or other
equipment.
WARNING The combined weight of the display placed on the wall mount must not exceed 200 lbs
(90.72kg),the maximum support weight of the mount.
WARNING Watch for pinch points. Do not put your fingers between movable parts.
WARNING Make sure the flag securing the display is completely lowered at all times except when
removing or installing the display. The flag must be all the way down when
installing/removing cables.
CAUTION Check the unit for shipping damage before you begin the installation.
Installation Instructions PLP Series
3
DIMENSIONAL
DRAWING
17.00
.69
1.87
4.24
15.51
18.38
13.19
16.00
16.00
16.00
24.00
5/16" x 1" SLOT
5/16" x 6" SLOT
5/16" x 1" SLOT
TOP MOUNTING BUTTON ON
PSB-XXXX DRAWING GOES HERE
26.00
1.83
FACE TILTS
15 DOWN
7 UP (FOR SERVICE)
NOTE: CUSTOM INTERFACE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
WILL ADD BETWEEN 1/2" AND 2" IN DEPTH
AND MAY AFFECT LOCATION OF DISPLAY
ON THE MOUNT.
SEE PSB-XXXX DRAWING ALSO.
C

Especificaciones del producto

Marca: Chief
Categoría: soporte de panel plano
Modelo: PLP2000B

¿Necesitas ayuda?

Si necesitas ayuda con Chief PLP2000B haz una pregunta a continuación y otros usuarios te responderán


soporte de panel plano Chief Manuales

Chief

Chief PFQUB Manual de Usario

17 Septiembre 2024
Chief

Chief VPAU Manual de Usario

16 Septiembre 2024
Chief

Chief MFQUB Manual de Usario

15 Septiembre 2024
Chief

Chief PFMUB Manual de Usario

15 Septiembre 2024
Chief

Chief RXF3 Manual de Usario

14 Septiembre 2024
Chief

Chief PNR2536B Manual de Usario

3 Septiembre 2024
Chief

Chief K4G210B Manual de Usario

3 Septiembre 2024
Chief

Chief MF26000B Manual de Usario

3 Septiembre 2024
Chief

Chief FSB018BLK Manual de Usario

3 Septiembre 2024
Chief

Chief TPK1 Manual de Usario

3 Septiembre 2024

soporte de panel plano Manuales

Últimos soporte de panel plano Manuales

Cabstone

Cabstone BeamerFlex 51945 Manual de Usario

27 Octubre 2024
Nec

Nec PDVWXUN 55 P Manual de Usario

15 Octubre 2024
Insignia

Insignia NS-STV3N1705 Manual de Usario

15 Octubre 2024
Abus

Abus BW8060 Manual de Usario

4 Octubre 2024
Nec

Nec PD01CMB Manual de Usario

2 Octubre 2024
One For All

One For All DM 4110 Manual de Usario

1 Octubre 2024
One For All

One For All DM 7220 Manual de Usario

1 Octubre 2024
One For All

One For All DM 2220 Manual de Usario

1 Octubre 2024
Kogan

Kogan KASMM39S12A Manual de Usario

1 Octubre 2024
Kogan

Kogan KATWM70TLMA Manual de Usario

1 Octubre 2024