Chief PRO2000B Manual de Usario

Chief soporte de panel plano PRO2000B

Lee a continuación 📖 el manual en español para Chief PRO2000B (6 páginas) en la categoría soporte de panel plano. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/6
I N S T A L L A T I O N I N S T R U C T I O N S
Large Flat Panel Wall Mount
Model: PRO-2000 Series
PRO-2000 Series Wall Mount Features:
• Accommodates large flat screens weighing up to
200 lbs (90.7 kg).
• Mounting brackets adapt to either 16" or 24" on
center dual stud wood framework; integrated
lateral shift adjusts ± 4.5" (16" on center) or ± 0.5"
(24" on center).
• Infinite tilt and lock adjustment between 0-15
degrees.
• Chief's exclusive Q-Latch mounting system
provides convenient and secure display connect/
disconnect; optional padlock provides additional
display security.
Q-Latch® is a registered trademark of Chief Mfg.
! IMPORTANT: If the installation of this product requires
OSHPD seismic approval, refer to OSHPD pre-approval
documents and drawings before beginning installation.
OSHPD documents and drawings are available at
www.chiefmfg.com, and are also located on the product
information page for the mount. PRO-2000 Series
BEFORE YOU BEGIN
CAUTION: To prevent damage to your monitor and PRO-2000, which could affect or void the Factory warranty,
thoroughly study all instructions and illustrations before you begin to install the mount. Pay particular attention to the
Warnings and Cautions in this document.
• The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor
the mount must be capable of supporting five times the total weight of the equipment.
• The maximum weight to be installed on the PRO-2000 wall mount is 200 lbs (90.7 kg).
• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-
6480.
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE 700
SAVAGE, MINNESOTA 55378 USA
8805-000140 (Rev. E)
2007 Chief Manufacturing
www.chiefmfg.com
10/07
Installation Instructions
2
IMPORTANT WARNINGS AND CAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: It is the installer’s responsibility to make sure structure to which this mount is attached can support five
times the combined weight of all equipment. Reinforce the structure as required before installing the accessory.
Failure to provide adequate structural strength for the mount can result in serious personal injury or damage to
equipment!
WARNING: It is the installer’s responsibility to make sure all components are properly assembled and installed using
instructions provided. Failure to follow instructions can result in serious personal injury or damage to equipment!
WARNING: It is the installer’s responsibility to make sure combined weight of mount, display, and all attached
equipment must not exceed 200 lbs (90.7 kg), the maximum support weight of this mount. Exceeding maximum
support weight can result in serious personal injury or damage to equipment!
WARNING: Watch for pinch points. Do not put your fingers between movable parts.
WARNING: Make sure the Q-Latches securing the display are fully latched at all times except when removing or
installing the display. The Q-Latches must be fully latched when installing/removing cables.
CAUTION: Check the unit for shipping damage before you begin the installation.
DIMENSIONAL DRAWING
Installation Instructions
3
TOOLS REQUIRED FOR INSTALLATION
• Drill and drill bit set
• Socket wrench set
NOTE: Other tools may be required depending on your method of installation.
PARTS
Unpack carton, inspect and verify contents.
Read installation instructions completely. If any listed
parts are missing, contact Chief Customer Service at
1-800-582-6480.
Table 1: Parts
10 MOUNT, PRO-2000 Series 1
20 BOLT, Lag, 5/16" x 2-½" 4
30 WASHER, 5/16" 4
10
20 - 4 Lag Bolts
30 - 4 Washers

Especificaciones del producto

Marca: Chief
Categoría: soporte de panel plano
Modelo: PRO2000B

¿Necesitas ayuda?

Si necesitas ayuda con Chief PRO2000B haz una pregunta a continuación y otros usuarios te responderán


soporte de panel plano Chief Manuales

Chief

Chief PFQUB Manual de Usario

17 Septiembre 2024
Chief

Chief VPAU Manual de Usario

16 Septiembre 2024
Chief

Chief MFQUB Manual de Usario

15 Septiembre 2024
Chief

Chief PFMUB Manual de Usario

15 Septiembre 2024
Chief

Chief RXF3 Manual de Usario

14 Septiembre 2024
Chief

Chief PNR2536B Manual de Usario

3 Septiembre 2024
Chief

Chief K4G210B Manual de Usario

3 Septiembre 2024
Chief

Chief MF26000B Manual de Usario

3 Septiembre 2024
Chief

Chief FSB018BLK Manual de Usario

3 Septiembre 2024
Chief

Chief TPK1 Manual de Usario

3 Septiembre 2024

soporte de panel plano Manuales

Últimos soporte de panel plano Manuales

Cabstone

Cabstone BeamerFlex 51945 Manual de Usario

27 Octubre 2024
Nec

Nec PDVWXUN 55 P Manual de Usario

15 Octubre 2024
Insignia

Insignia NS-STV3N1705 Manual de Usario

15 Octubre 2024
Abus

Abus BW8060 Manual de Usario

4 Octubre 2024
Nec

Nec PD01CMB Manual de Usario

2 Octubre 2024
One For All

One For All DM 4110 Manual de Usario

1 Octubre 2024
One For All

One For All DM 7220 Manual de Usario

1 Octubre 2024
One For All

One For All DM 2220 Manual de Usario

1 Octubre 2024
Kogan

Kogan KASMM39S12A Manual de Usario

1 Octubre 2024
Kogan

Kogan KATWM70TLMA Manual de Usario

1 Octubre 2024