Chief RPMB191 Manual de Usario

Chief soporte de panel plano RPMB191

Lee a continuación 📖 el manual en español para Chief RPMB191 (1 páginas) en la categoría soporte de panel plano. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-000260 Rev01

a Duchossois Group Company

05/09

SSB-191, SSM-191, SLB-191 and SLM-191 Interface Brackets

SSB-191, SSM-191, SLB-191 and SLM-191 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation Instructions

WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Place 1/2" nylon spacers over the threaded inserts in the bottom of the projector.

4. Place the interface bracket onto the 1/2" nylon spacers on the bottom of the projector and align the mounting holes in the bracket with the

nylon spacers.

5. Using the M4 x 20mm pan head screws and M4 washers, position screws with washers into the side holes and position the M4 flat head

screws in the counter sink holes. Tighten all fasteners at this time, securing the bracket to the projector.

NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation

instructions in the All-Points Security Kit.

(1) Interface Bracket (2) Screw, Phillips pan head, M4 x 20mm

(4) 10-24 Thumb Nuts ** (2) Screw, Phillips flat head, M4 x 20mm

(1) All-Points Security Kit (4) Spacer, Nylon, 1/2" x .194 x 1/2"

(2) Washer, Flat, M4

**Only used when installing SLB/SSB interface brackets.

NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the

encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style

interface bracket installation.

SLB-191 SLM-191

(

)

(

Note: SSB-style interfa

)

Towards front of

projector

Towards front of

projector

Especificaciones del producto

Marca:	Chief
Categoría:	soporte de panel plano
Modelo:	RPMB191
Peso.:	2345 g
Ancho:	240 mm
Profundidad:	80 mm
Altura:	255 mm
estándares 2G:	EDGE, GPRS, GSM
estándares 3G:	HSDPA, HSUPA, UMTS
Estándares wifi:	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Generación de internet móvil:	3G
red LAN:	Ja
Número de puertos Ethernet LAN (RJ-45):	1
banda wifi:	Nee
Estándar Wi-Fi:	Wi-Fi 4 (802.11n)
Tipo de interfaz Ethernet LAN:	Fast Ethernet
LAN Ethernet, velocidades de transferencia de datos:	10, 100 Mbit/s
Tecnología de cableado:	10/100Base-T(X)
Estándar de red:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Algoritmos de seguridad compatibles:	128-bit WEP, 64-bit WEP, TKIP, WPA, WPA-PSK, WPA2, WPA2-PSK
3G:	Ja
Conexión de red móvil:	Ja
Gestión basada en web:	Ja
Red WAN:	Ja
Servidor DHCP:	Ja
cliente DHCP:	Ja
Temperatura de funcionamiento (TT):	-20 - 65 °C