Cisco C1121X-8PLTEP Manual de Usario

Cisco Enrutador C1121X-8PLTEP

Lee a continuación 📖 el manual en español para Cisco C1121X-8PLTEP (90 páginas) en la categoría Enrutador. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/90

Hardwa r e Installation Guide for the Cisco 1000 Series Integrated

Services Router

Last Modified: 2019-06-07

Last Modified: 2020-07-23

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95 134-1706

USA

http://www.cisco.com

Tel: 408 52 6-40 00

800 553- NETS (6387)

Fax: 408 527-0883

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15

of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are

encouraged to try to correct the interference by using one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network

topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional

and coincidental.

All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.

Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:

https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a

partnership relationship between Cisco and any other company. (1721R)

C O N T E N T S

Overview of Cisco 1000 Series Integrated Services Routers 1

C H A P T E R 1

About Cisco 1000 Series Integrated Service Routers 1

Chassis Views 4

LED Indicators 13

Reset Button 20

Power Supply 20

Slots and Interfaces 21

About Slots, Subslots, and Port Numbering 21

Specifications of Cisco 1100 Series Integrated Services Routers 21

Periodic Inspection and Cleaning 21

Prepare for Router Installation 23

C H A P T E R 2

Safety Recommendations 23

Safety With Electricity 24

Prevent Electrostatic Discharge Damage 24

General Site Requirements 24

Site Selection Guidelines 25

Rack Requirements 25

Safety Recommendations 26

Power Guidelines and Requirements 26

Network Cabling Specifications 27

Console Port Considerations 27

EIA/TIA-232 27

USB Serial Console 27

Console Port Considerations 28

Prepare for Router Installation 29

Hardware I nstallation Guide for the Cisco 1000 Series Integrated Services Router

iii

Especificaciones del producto

Marca:	Cisco
Categoría:	Enrutador
Modelo:	C1121X-8PLTEP
Colocación del dispositivo:	Ingebouwd
Tipo de operación:	Touch
Color del producto:	Black, Stainless steel
Número de niveles de potencia:	3
Pantalla incorporada:	Nee
Temporizador:	Ja
Ancho:	380 mm
Profundidad:	520 mm
Altura:	54 mm
Tipo de material (arriba):	Roestvrijstaal
Número de quemadores/zonas de cocción:	2 zone(s)
tipo de placa:	Inductiekookplaat zones
Número de zonas de cocción electrónicas:	2 zone(s)
Quemador normal/zona de cocción:	1400 W
Posición de control:	Boven voorzijde
Carga conectada (eléctrica):	2800 W
Indicadores LED:	Ja
Interruptor encendido / apagado:	Ja
dominó:	Ja