Crunch PZ-1520.4 Manual de Usario

Crunch receptor PZ-1520.4

Lee a continuación 📖 el manual en español para Crunch PZ-1520.4 (2 páginas) en la categoría receptor. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Place terminal in a secure

position so that it won’t

accidentally contact the

negative battery post

Power / Ground

cable size

It is critical to use the proper

power and ground cable. Select

the size listed here for your

amplier model. Always use high

quality copper cable.

Cable size recommendations for

multi amp systems are available

on our website.

Properly route power,

speaker and RCA cables

through the vehicle.

Choose a mounting location

that will provide adequate air

ventilation. Mount the amplier to

a secure surface. Do not mount

the amplier upside down.

Using spade terminals, connect the

+12V to the power cable from the

battery, the REM to the source unit

turn-on wire and the GND to the

chassis ground..

Strip each cable back approx 1/2”,

connect the +12V to the power

cable from the battery, the REM to

the source unit turn-on wire and the

GND to the chassis ground..

Bare metal

Connect the RCA cables to

the INPUT connectors. The

OUTPUT can be used to

provide input for a second

amplier.

The HI INPUT is for use with

source units that do not offer

RCA outputs. Use the supplied

harness to connect to the

source unit’s speaker output.

Connect the power cable to the

positive battery terminal. The

power cable must be fused

within 18 inches of the battery

terminal.

Re-connect the negative

battery terminal making sure it

is securely tightened.

Using spade terminals,connect

the speaker cables to the speaker

output connectors. Follow the

diagram below that best ts your

speaker conguration.

The chassis ground connection

is critical to the performance

of the amplier. Choose a

location that is close to the

amplier. Completely scrape

away the paint and use a nut

and bolt if possible.

DO NOT USE AN EXISTING

FACTORY BOLT!

Disconnect

negative battery

terminal

Run Cables

Mount Amplier

Power

Connections

Smaller amps

Signal Input

Low Level RCA

Power

Connections

Larger amps

Signal Input

High Level

Positive Battery

Connection

Re-connect

Negative Battery

Terminal

Speaker

Connections

Chassis Ground

Be prepared to disarm your vehicle’s alarm and

to enter your radio / source unit code.

Stereo

Installation

Before you start

Monoblock single woofer multiple woofersMonoblock

Bridged

CAUTION

Many new and factory radios require a reset code when

disconnected from battery power. This is an anti-theft

feature. Before unplugging power, you must determine if

your radio/source unit requires a reset code. Check the

operation manual for your vehicle or contact the dealer.

Turn the LEVEL control completely

counter-clockwise to minimum.

Level Control

6V 0.2V

INPUT

LEVEL

Right + (gray) 4CH REAR

Ch3 Right + (orange)

Ch3 Right - (pink)

Chassis Ground (black)

Ch4 Left + (blue)

Ch4 Left - (yellow)

Connect to factory speaker wire directly

Right - (brown)

Left - (green)

Left + (white)

Chassis ground (black)

4ga

Model Fuse Size Cable Size

PZ-820.2

PZ-1020.2

PZ-1520.2

PZ-2020.2

PZ-3520. 2-Pro

PZ-1020.4

PZ-1520.4

PZ-2020.4

PZ-4020.4- Pro

PZ- 3020.1D

PZ- 402 0.1D

PZ- 5020.1D

1- 30A

1-35A

2-30A

2-35A

2-15A

2-20A

2-25A

2-40A

1-60A

1-80A

2-60A

Setup Common System Setup

Quick Start

Installation Guide

The input MODE switch will “sum” or

combine the right and left channel signals

in the MONO position to improve bass

performance. Select MONO only when the

amp is being used for subwoofers.

The XOVER Mode switch sets the type

of crossover that will be active. 4 channel

models will have two switches, one for each

set of channels.

The HPF(high pass lter) control will limit the

output below the selected frequency. This

is typically used to protect midrange and hi

frequency speakers from damage and to

allow a smooth transition from a subwoofer.

The LPF(low pass lter) control will limit

output above the selected frequency. This

is used to allow a smooth transition to the

higher frequency speakers.

1. If possible, with the source unit off, conrm that the primary volume control is

turned down (counter clockwise).

2. Turn on the source unit (CD, or MP3 player). Re-conrm that the volume is

turned down. Make sure the source unit controls; balance, fader, bass and

treble are all set to center or “0” adjustment. Make sure that the green LED on

the end of the amplier is illuminated.

3. Play a clean musical selection of which you are very familiar. CD is preferred.

Do not use radio signals for level setting. Hit play and start turning the volume

of the source unit up.

4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until

you hear speakers begin to slightly start producing distortion.

5. Increase the amplier level (clockwise) until distortion is heard, then back

the level down (counter clockwise) until the distortion is eliminated. Small

adjustments may need to be made to balance the levels of multiple ampliers.

The BASS BOOST or BASS EQ control

will increase the output at 45Hz for more

pronounced bass. Exercise caution.

Increase the level in small amounts until

distortion is noticed, then back off a little.

Some models include a bass

remote. Avoid adjusting the bass

remote while operating vehicle.

Input Mode

Xover Mode

High pass

Adjustment

Low pass

Adjustment

Bass Boost

Remote Level

Control

2ch - Full Range

4ch - Full Range

4ch - Mixed Mono

Mono

This is a critical step to insure your amplier

is properly adjusted to match the signal

output level of your source unit.

THIS IS NOT A VOLUME CONTROL!

Level Setting

WARRANTY

Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from

defects in material and workmanship for a period of one (1) year from the date of purchase.

Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty

period. Components that prove to be defective in materials and workmanship under proper installation

and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was

purchased. A photocopy of the original receipt must accompany the product being returned. The

costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics

USA Inc. This warranty is limited to defective parts and specically excludes any incidental or

consequential damages connected therewith. To view the full warranty, please visit the website.

The information contained within this document is intended to offer some basic guidelines

for a few of the most common installations. More complex audio systems should be

installed by a competent professional. Additional installation information available at

www.maxxsonics.com

Crunch products are designed and engineered in the USA by

www.maxxsonics.com

PZ-820.2

PZ-1020.2

PZ-1520.2

PZ-2020.2

PZ-3520.2-Pro

PZ-1020.4

PZ-1520.4

PZ-2020.4

PZ-4020.4-Pro

PZ-3020.1D

PZ-4020.1D

PZ-5020.1D

Congratulations on your choice of a Crunch amplier. This

“Quick Start Installation” guide is meant to help you “hook

up” and play music. For more detailed information, on

system setting, speaker and subwoofer conguration and

full specications by model visit the website,

http://crunchcaraudio.com/manuals

CR PZ QSG 01 - rev1

Especificaciones del producto

Marca:	Crunch
Categoría:	receptor
Modelo:	PZ-1520.4
Color del producto:	Zwart
Consumo-anual-de-energía:	31 kWu
Peso del embalaje:	3800 g
Ancho del embalaje:	600 mm
Empaquetadura en profundidad:	100 mm
Altura del embalaje:	390 mm
Clase de eficiencia energética (antigua):	A
Diagonal de la pantalla:	22 "
Resolución:	1920 x 1080 Pixels
Relación de aspecto original:	16:9
Formato de audio soportado:	AAC, MP3, WAV, WMA
Formatos de vídeo soportados:	AVC, AVI, H.264, MKV, MPEG1, MPEG2, MPEG4, VC-1, WMV9
red LAN:	Nee
Formatos de compresión de vídeo:	HEVC
Cables suministrados:	AC
Forma de pantalla:	Flat
Brillo:	250 cd/m²
Guía de inicio rápido:	Ja
Tarjeta de garantía:	Ja
Número de puertos USB 2.0:	1
Puerto(s) VGA (D-Sub):	1
Número de puertos HDMI:	2
Puerto DVI:	Nee
Televisión inteligente:	Nee
Altavoces incorporados:	Ja
Energía promedio:	6 W
Consumo de energía (en espera):	0.3 W
Número soportado de baterías/baterías:	2
Salidas de auriculares:	1
Formato de señal analógica:	NTSC, PAL, SECAM
Consumo de energía (cuando está apagado):	0.3 W
tipo HD:	Full HD
3D:	Nee
Formato de imagen soportado:	BMP, GIF, JPG, PNG
Tecnología de visualización:	LED
Tiempo de respuesta:	- ms
Montaje VESA:	Ja
Interfaz de montaje en panel:	75 x 75 mm
Profundidad (sin base):	45.7 mm
Altura (sin base):	308 mm
Ancho (sin base):	512.3 mm
Peso (sin base):	2560 g
Diámetro de la pantalla en centímetros.:	55 cm
Entrada de PC (D-Sub):	Ja
Audio digital, salida óptica.:	1
Interfaz común Plus (CI+):	Ja
tipo de sintonizador:	Analoog & digitaal
Formato de señal digital:	DVB-C, DVB-T, DVB-T2
televisión por internet:	Nee
Ancho del dispositivo (con soporte):	512.3 mm
Dispositivo de profundidad (con soporte):	112 mm
Altura del dispositivo (con soporte):	315.9 mm
Peso (con soporte):	2590 g
soporte de escritorio:	Ja
Posibilidades de ajustar las dimensiones de la pantalla.:	4:3, 16:9, Auto
Teletexto:	Ja
Control automático de volumen:	Ja
Temporizador de encendido/apagado:	Ja
guía de televisión electrónica:	Ja
Canal de retorno de audio (ARC):	Ja
Control de electrónica de consumo (CEC):	EasyLink
Interfaz común (CI):	Ja
Número de puertos RF:	1
Teletekst:	1000 pagina's
Función de subtítulos:	Ja
Periodo de programación:	8 dag(en)
Modo ecologico:	Ja
Es posible actualizar el firmware:	Ja
El firmware se puede actualizar mediante:	Auto upgrade wizard, USB
Número de puertos SCART:	1
Formatos de subtítulos admitidos:	ASS, SMI, SRT, SSA, SUB, TXT
Indicación de intensidad de señal:	Ja
Atenuación de imagen (para radio):	Ja
Tipo de conexión RF:	IEC
Mando a distancia incluido:	Ja
Wifi.:	Nee
voltaje-de-entrada-de-CA:	220 - 240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Consumo de energía (típico):	21 W
Temperatura de funcionamiento (TT):	5 - 35 °C
Baterias-incluidas:	Ja
Entrada de audio para DVI:	Ja
Tipo de Batería:	AAA