CRUX DKGM-48D Manual de Usario

Lee a continuación 📖 el manual en español para CRUX DKGM-48D (4 páginas) en la categoría No categorizado. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
- Retains factory features in select GM Class II Data Bus vehicles while functioning with an
aftermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- Voice Recognition Command from factory SWC.
- Supports Bose, Y-91 and non-amplified audio systems.
- Retains chime functions.
- Built-in chime volume adjustment.
- Double DIN Dash Kit included.
- EIA color coded wiring for easy installation.
GM- D Module 48
GM- D Harness (GM-C2) 48
SWC Cables
Double DIN Dash Kit
1. The Front and Rear fading are not retained on Y-91 Bose System.
2. Chime includes: seat belt, check engine, key in ignition, low fuel, low oil and lights on.
rev.092821
1/4
SETTING THE AFTERMARKET RADIO BRAND
With the key in the off position, set the DIP switches to the corresponding radio listed below. See page 4 for SWC
button functions.
3.5MM SWC CABLE
The SWRGM- D Module allows for both types of connections: 48
OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is attached)
is used for BOSS, DUAL, FAHRENHEIT, JENSEN, PIONEER, POWER ACOUSTIK, SONY & OPTION B
SOUND STREAM units.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
If the vehicle is equipped with a Bose system, the DKGM- D has a built-in Bose adaptor that allows the proper audio 48
input gain from the aftermarket radio to the Bose amplifier. To use this feature, plug in the male 8-pin connector on
the harness to the GRAY female 8-pin connector on the GM- D 48 module. The module is also labeled Bose” and
“Non Bose” to avoid confusion. (see picture below)
If the vehicle is NOT equipped with a Bose system, plug in the male 8-pin connector to the BLACK female 8-pin on
the GM- D module. 48
2/4
BOSE
Connection
Non-BOSE
Connection
rev.092821
The - D has a potentiometer to adjust the chime volume. It is set at half way by default. To adjust the DKGM 48
volume, simply use a suitable screwdriver and turn the potentiometer clockwise to increase the volume and
counter-clockwise to decrease the volume.
Dash Kit Assembly
Please make sure that you have all the parts shown below.
(1) Main trim ring
(1) Left ISO mounting bracket
(1) Right ISO mounting bracket
3/4
rev.092821

Especificaciones del producto

Marca: CRUX
Categoría: No categorizado
Modelo: DKGM-48D

¿Necesitas ayuda?

Si necesitas ayuda con CRUX DKGM-48D haz una pregunta a continuación y otros usuarios te responderán




No categorizado CRUX Manuales

CRUX

CRUX SOOGM-16 Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKGM-16W Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKVW-52B Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKVW-52 Manual de Usario

19 Septiembre 2024
CRUX

CRUX ACP-MAX Manual de Usario

19 Septiembre 2024
CRUX

CRUX RFM-MG1 Manual de Usario

19 Septiembre 2024
CRUX

CRUX SOCGM-18L Manual de Usario

19 Septiembre 2024
CRUX

CRUX SWRGM-49L Manual de Usario

19 Septiembre 2024
CRUX

CRUX WVICH-03M Manual de Usario

19 Septiembre 2024
CRUX

CRUX WVIFD-02F Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales