CRUX DKGM-48S Manual de Usario

Lee a continuación 📖 el manual en español para CRUX DKGM-48S (8 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
- Retains factory features in select GM Class II Data Bus vehicles while functioning with an
aftermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- Voice Recognition Command from factory SWC.
- Supports Bose, Y-91 and non-amplified audio systems.
- Retains chime functions.
- Built-in chime volume adjustment.
- Single DIN Dash Kit included.
- EIA color coded wiring for easy installation.
GM- Module 48S
GM- Harness (GM-C2) 48S
SWC Cables
Single DIN Dash Kit
1. The Front and Rear fading are not retained on Y-91 Bose System.
2. Chime includes: seat belt, check engine, key in ignition, low fuel, low oil and lights on.
1 /8
rev.092821
SETTING THE AFTERMARKET RADIO BRAND
With the key in the off position, set the DIP switches to the corresponding radio listed below. See page 8 for SWC
button functions.
3.5MM SWC CABLE
The SWR - Module allows for both types of connections: GM 48S
OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is attached)
is used for ATOTO, BOSS, DUAL, FAHRENHEIT, JENSEN, PIONEER, POWER ACOUSTIK, SONY,OPTION B
SOUND STREAM and other Off-Brand headunits.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
If the vehicle is equipped with a Bose system, the - has a built-in Bose adaptor that allows the proper audio DKGM 48S
input gain from the aftermarket radio to the Bose amplifier. To use this feature, plug in the male 8-pin connector on
the harness to the GRAY female 8-pin connector on the -48S GM module. The module is also labeled “Bose” and
“Non Bose” to avoid confusion. (see picture below)
If the vehicle is NOT equipped with a Bose system, plug in the male 8-pin connector to the BLACK female 8-pin on
the - module. GM 48S
2/8
BOSE
Connection
Non-BOSE
Connection
rev.092821
The - has a potentiometer to adjust the chime volume. It is set at half way by default. To adjust the DKGM 48S
volume, simply use a suitable screw driver and turn the potentiometer clockwise to increase the volume and
counter-clockwise to decrease the volume.
Please make sure that you have all the parts shown below.
3/8
rev.092821

Especificaciones del producto

Marca: CRUX
Categoría: No categorizado
Modelo: DKGM-48S

¿Necesitas ayuda?

Si necesitas ayuda con CRUX DKGM-48S haz una pregunta a continuación y otros usuarios te responderán




No categorizado CRUX Manuales

CRUX

CRUX SOOGM-16 Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKGM-16W Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKVW-52B Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKVW-52 Manual de Usario

19 Septiembre 2024
CRUX

CRUX ACP-MAX Manual de Usario

19 Septiembre 2024
CRUX

CRUX RFM-MG1 Manual de Usario

19 Septiembre 2024
CRUX

CRUX SOCGM-18L Manual de Usario

19 Septiembre 2024
CRUX

CRUX SWRGM-49L Manual de Usario

19 Septiembre 2024
CRUX

CRUX WVICH-03M Manual de Usario

19 Septiembre 2024
CRUX

CRUX WVIFD-02F Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales