CRUX RVCCH-75C Manual de Usario

CRUX No categorizado RVCCH-75C

Lee a continuación 📖 el manual en español para CRUX RVCCH-75C (3 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/3
RVCCH-75C
Rear View Integration Interface with VIM
for CHRYSLER, DODGE & JEEP
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • Chatsworth, California
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.020520
1 of 3
Acvates Uconnect Touchscreen Radio for enabling Video features
Aermarket Rear-view Camera included
Automacally switches to Rear-view when car is in Reverse mode
Forced reverse camera view feature
• VIM funcon
Plug & Play Installaon
PRODUCT FEATURES:
PARTS INCLUDED:
RVCCH-75C Module RVCCH-75C Harness CCH-01G Camera
INSTALLATION DIAGRAM:
WHITE Wire
Parking Guideline
To Radio
OEM Radio
Harness
DP
ON
DIP
SWITCH
LED*
*LED RED = Power ON Status
LED BLUE = Data Bus ON Status
RVC Video
Signal Input
RED Wire Push in Connectors
all the way
Line up Arrows
Regulator
20 Ft. Coax Cable
RED Wire
Tape O
(Not Used)
BLACK
Wire
BLACK
(Ground)
8-Pin Molex Represents Solder Joint
Connect RCAs and secure
with tape all around
WHITE Wire
(Camera Power Output
+12V 250mA)
OR*
*Connect BLACK (ground) wire to a source ground and not
chassis ground (i.e. ground wire on reverse light)
If video noise is present, we recommend connecting the
ground wire to the BLACK ground wire on the RVCCH-75C harness.
Source Ground
GREEN Wire
For Non Permanent
VIM function
Crux Interfacing Solutions • Chatsworth, California
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.020520
2 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
DIP SWITCH SETTINGS:
INSTALLATION INSTRUCTIONS:
INSTALLING THE CDR-02 CAMERA AND CABLE
1. Remove the rear panel lip.
2. Drill a 5/8 inch size hole in the available locaon.
3. Fish the wires thought the drilled hole and through the pass through into the trunk/cargo area.
4. Route the wires towards the radio and make the power and video connecons. For powering up the camera, use the 12V
OUTPUT (White Wire). (See Wiring Diagram on page 1)
5. Connect the camera ground wire to chassis ground. If video noise is present, we recommend grounding the camera
directly to the BLACK wire on the RVCCH-75C T-harness.
6. Test the camera before re-installing the radio.
CODING THE RADIO FOR A REAR VIEW CAMERA
The radio has to be coded to accept a reverse camera. Please follow the coding procedure below:
1) Turn key o and remove the key from ignion.
2) Open the driver door then close it (make sure all doors, li gate and hood are also closed).
3) Look at the module and wait for LEDs to turn o then disconnect the module.
4) Before plugging back the module, turn all DIP switches to ON then OFF.
5) Set DIP switches 1 (if permanent VIM is desired), 2 and 6 to the ON posion.
6) Reconnect module and wait for the LEDs to turn o.
7) Start up engine and the coding operaon is complete.
8) Put the gear in reverse to test the camera.
FORCED VIEW OF REVERSE CAMERA
The Force RVC is used to view the back-up camera when the vehicle is
not in reverse gear. Allows you to view what is in the back while driving.
To acvate this feature, make sure that DIP 4 is set to ON. Press the center
buon once on the le hand side steering wheel control (located behind the steering wheel).
NOTE: The camera is defaulted to power down aer 10 seconds.
DIP SWITCH FUNCTIONS:
DIP 1 = Video in Moon Acvaon ON / OFF
DIP 2 = Rear View Camera ON / OFF
DIP 3 = Not Used
DIP 4 = Forced RVC ON / OFF
DIP 5 = Defaulted to OFF*
DIP 6 = Defaulted to ON*
RVCCH-75C
Rear View Integration Interface with VIM
for CHRYSLER, DODGE & JEEP
*DIP 5 & 6
If the radio is having turn-on issues, please try the following:
Aempt 1: Set 5 & 6 to ON
Aempt 2: Set 5 to ON and 6 to OFF
Aempt 3: Set 5 to OFF and 6 to ON
1 2 3 4 5 6
ON
Crux Interfacing Solutions • Chatsworth, California
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.0205203 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCCH-75C
Rear View Integration Interface with VIM
for CHRYSLER, DODGE & JEEP
VEHICLE APPLICATIONS:
CHRYSLER
2015 - 2016 300
NOTES:
1. Not compable on vehicles with heated seats or heated steering wheel.
COMPATIBLE RADIOS:
8.4” Screen with Separate Knobs 5” Screen with 6 Buons & Separate Knobs
4.3” Screen with 4 Buons & 2 Knobs
(monochrome display)
Not compable radio
DODGE
2014 - 2017 Durango
2015 - 2015 Charger
2013 - 2017 Challenger
JEEP
2014 - 2017 Grand Cherokee
For radios without a separate CD slot (one piece radio).

Especificaciones del producto

Marca: CRUX
Categoría: No categorizado
Modelo: RVCCH-75C

¿Necesitas ayuda?

Si necesitas ayuda con CRUX RVCCH-75C haz una pregunta a continuación y otros usuarios te responderán




No categorizado CRUX Manuales

CRUX

CRUX SOOGM-16 Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKGM-16W Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKVW-52B Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKVW-52 Manual de Usario

19 Septiembre 2024
CRUX

CRUX ACP-MAX Manual de Usario

19 Septiembre 2024
CRUX

CRUX RFM-MG1 Manual de Usario

19 Septiembre 2024
CRUX

CRUX SOCGM-18L Manual de Usario

19 Septiembre 2024
CRUX

CRUX SWRGM-49L Manual de Usario

19 Septiembre 2024
CRUX

CRUX WVICH-03M Manual de Usario

19 Septiembre 2024
CRUX

CRUX WVIFD-02F Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales