CRUX SWRSB-58 Manual de Usario

Lee a continuación 📖 el manual en español para CRUX SWRSB-58 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
RAD IO R EP LAC EME NT
SWC R ETE NTI ON
+
R
INTERFACING SOLUTIONS
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.072322
SWRSB-58
Radio Replacement with Steering Wheel Retention
for select Saab Vehicles
1 of 2
PRODUCT FEATURES:
PARTS INCLUDED:
- Retains factory features in select Saab vehicles while funconing with an aermarket radio.
- Retains Steering Wheel Controls via built-in, pre-programmed interface.
- With navigaon outputs (Reverse gear , Illuminaon and Speed signal).
- Provides Accessory Power ( 2A MAX ).
SWRSB-58 MODULE SWRSB-58 Harness SWRSB-58 Harness B SWC Cables
INSTALLATION DIAGRAM:
AFTERMARKET
RADIO
illumination (+) Orange
Reverse Gear Red/White
Vehicle Speed Sense Purple/White
+12V Constant Yellow
+12V ACC Red
Ground Black
Amp Turn on Blue
Right Front (+) Gray
Right Front (-) Gray/Black
Left Front (+) White
Left Front (-) White/Black
Right Rear (+) Violet
Right Rear (-) Violet/Black
Left Rear (+) Green
Left Rear (-) Green/Black
TO FACTORY
HARNESS
12-Pin Black
Connector
1 2 3
ON
4-Pin
Connector
Option A:
Option B:
Cap or insulate if
not being used
BLUE / YELLOW
3.5MM SWC CABLES (Option A or B)
Use the proper 3.5MM to 4-Pin cable for your radio.
Plug in the selected 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
To aftermarket
Radio SWC Port
For Kenwood & JVC
NOTE:
Compable with vehicles with non-amplied and standard amplied systems.
The SWRSB-58 includes 2 harnesses. Use the harness that matches the factory connectors on your
vehicle. See installaon diagrams for each harness.
RADIO REPLACEMENT
R
INTERFACING SOLUTIONS
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.072322
SWRSB-58
Radio Replacement with Steering Wheel Retention
for select Saab Vehicles
2 of 2
SAAB
2004 - 2005 9-3 2000 - 2005 9-5
VEHICLE APPLICATIONS:
TO FACTORY
HARNESS
AFTERMARKET
RADIO
illumination (+) Orange
Reverse Gear Red/White
Vehicle Speed Sense Purple/White
+12V Constant Yellow
+12V ACC Red
Ground Black
Amp Turn on Blue/White
Dimmer Orange/White
Power Antenna Blue
Right Front (+) Gray
Right Front (-) Gray/Black
Left Front (+) White
Left Front (-) White/Black
Right Rear (+) Violet
Right Rear (-) Violet/Black
Left Rear (+) Green
Left Rear (-) Green/Black
12-Pin Black
Connector
1 2 3
ON
4-Pin
Connector
Option A:
Option B:
Cap or insulate if
not being used
BLUE / YELLOW
3.5MM SWC CABLES (Option A or B)
Use the proper 3.5MM to 4-Pin cable for your radio.
Plug in the selected 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
To aftermarket
Radio SWC Port
For Kenwood & JVC
DIP SWITCH SETTINGS:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
RADIO BRAND: DIP#: 1 2 3
Atoto, Dual, Fahrenheit, Jensen
Pioneer, Power Acoustik, Soundstream
Blaupunkt, Most o-brand Radio
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony
OFF ON ON
OFF ON ON
OFF ON ON
OFF OFF OFF
ON ON OFF
ON ON ON
ON OFF ON
ON OFF OFF
OFF ON OFF
SWC MODULE
DIP SWITCH
1 2 3
ON
NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most o-brand radios,
check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
4-PIN SWC CABLE
Use the proper 3.5MM to 4-Pin SWC cable for the aermarket radio you are using. Plug it into the aermarket
radio’s SWC port or connect the Blue/Yellow wire to Kenwood and JVC radios.
OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is aached)
OPTION B is used for ATOTO, BLAUPUNKT, BOSS, DUAL, FARENHEIT, JENSEN, POWER ACOUSTIK, PIONEER,
SONY, SOUNDSTREAM and Most O-Brand Radios.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
RED to SWC Key 1
WHITE to SWC Key 2
SHIELD to SWC Ground
For aermarket radios that have wires for SWC connecons, cut o the 3.5mm plug on the Crux SWC Cable (opon B) and
connect the SWC wires as follows:
Note that there are some radios that only have SWC1 and
SWC2, in this case “shield does not need to be connected.

Especificaciones del producto

Marca: CRUX
Categoría: No categorizado
Modelo: SWRSB-58

¿Necesitas ayuda?

Si necesitas ayuda con CRUX SWRSB-58 haz una pregunta a continuación y otros usuarios te responderán




No categorizado CRUX Manuales

CRUX

CRUX SOOGM-16 Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKGM-16W Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKVW-52B Manual de Usario

19 Septiembre 2024
CRUX

CRUX DKVW-52 Manual de Usario

19 Septiembre 2024
CRUX

CRUX ACP-MAX Manual de Usario

19 Septiembre 2024
CRUX

CRUX RFM-MG1 Manual de Usario

19 Septiembre 2024
CRUX

CRUX SOCGM-18L Manual de Usario

19 Septiembre 2024
CRUX

CRUX SWRGM-49L Manual de Usario

19 Septiembre 2024
CRUX

CRUX WVICH-03M Manual de Usario

19 Septiembre 2024
CRUX

CRUX WVIFD-02F Manual de Usario

19 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales