DCS CAD1-SK Manual de Usario

DCS Parilla CAD1-SK

Lee a continuación 📖 el manual en español para DCS CAD1-SK (4 páginas) en la categoría Parilla. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
1
IMPORTANT:
Read all instructions before you begin. Do not jump ahead or skip any step.
CAUTION:
Some parts have sharp edges; care must be taken when handling the various components to
avoid injury. Be sure to use adequate manpower to assemble and install the side shelf to prevent
personal injury or damage to the unit.
NOTE: Avoid using side shelf to move cart. Push or pull cart by grasping corners of grill head. Never attempt to move a
hot grill. Allow unit to cool before touching.
GETTING STARTED
Remove packaging.
Contents Included:
Your side shelf is packaged in one box. The box contains your side
shelf, brackets, and installation hardware.
Tools Required:
Item No. Description Quantity
1
1
1
2
2
2
Shelf
(optional)
Work Gloves
5/32” Allen Wrench
3/16” Allen Wrench
Power Screwdriver or
Variable Speed Drill
with Phillips - tip
#2 Attachment
Bracket, Shelf-left
3/32” Allen Wrench
Bracket, Shelf-right
Bolt Shoulder, 5/16 x 1/4-20
Shoulder Bolt, 3/8 x 3/8 x 5/16-18
Screw, 10-24 X 1-1/8
1
2
5
3
4
6
SIDE SHELF (CAD-SK 70853)
INSTALLATION INSTRUCTIONS
1
2
3
4
5
6
Eye Protection
Fig. 03 Fig. 04
Attach Side Shelf Accessory on Either Side
NOTE: Side shelf Model CAD-SK can be installed with the head already on the cart.
1. Screw shoulder bolts (2) into the bottom screw holes on the side of the cart (Fig. 01 and 02). Tighten with 5/32
Allen wrench.
2. Slide left and right side shelf brackets over the shoulder bolt (Fig. 03) and install top screw attaching the side
shelf brackets onto the cart (Fig. 04). Tighten with Phillips screwdriver.
Fig. 01 Fig. 02
SHOULDER BOLT
SCREW HOLES
LEFT BRACKET
SCREW
2
3. Holding the side shelf, install 2 shoulder bolts (3/8 shoulder bolt) through the slots on the side shelf brackets into
the threaded holes on the side of the side shelf tray (Fig. 05). Tighten with a 3/16 Allen wrench (Fig. 06).
4. Locate the cart on flat level ground before attempting to level the side shelves. Place shelf in the up position and
check that it is level.
If the shelf is not level, adjust side shelf set screws. The set screws can be adjusted using a 3/32 Allen wrench
(Fig. 07). Turn the Allen wrench clockwise to raise the shelf. Turn 1/4 turn and review to see if the shelf is level.
The set screws in the left and right bracket should be adjusted equally to ensure the shelf sits level (Fig. 08).
Optional wood cutting board (model # CAD-WBC, 70861) shown in Figure 09 can be purchased as an accessory
from Customer Care at (888) 281-5698.
3
Fig. 07
Fig. 05 Fig. 06
Fig. 08
Fig. 09

Especificaciones del producto

Marca: DCS
Categoría: Parilla
Modelo: CAD1-SK

¿Necesitas ayuda?

Si necesitas ayuda con DCS CAD1-SK haz una pregunta a continuación y otros usuarios te responderán




Parilla DCS Manuales

DCS

DCS BND-CNR Manual de Usario

18 Septiembre 2024
DCS

DCS BE1-36RCI Manual de Usario

12 Septiembre 2024
DCS

DCS BH1-30R-N Manual de Usario

11 Septiembre 2024
DCS

DCS BH1-48R-N Manual de Usario

11 Septiembre 2024
DCS

DCS ADN1-20X30 Manual de Usario

11 Septiembre 2024
DCS

DCS BGC30-BQ-L Manual de Usario

11 Septiembre 2024
DCS

DCS CAD1-36E Manual de Usario

11 Septiembre 2024
DCS

DCS TB1-20 Manual de Usario

11 Septiembre 2024
DCS

DCS TDD120 Manual de Usario

11 Septiembre 2024

Parilla Manuales

Últimos Parilla Manuales