Delta Dore CV wind Manual de Usario

Delta Dore No categorizado CV wind

Lee a continuación 📖 el manual en español para Delta Dore CV wind (2 páginas) en la categoría No categorizado. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
Wind Sensor
Installation instructions
The wind sensor is designed to control
outdoor blinds automatically according
to wind speed and sunshine.
This sensor is associated via wireless
with one or more receivers controlling
the different shutters in your installation.
1. How does the sensor work?
2. Description
1.1 Presentation
Wind
sensor
Protective
covers
Display
Programming
keypad
Removal
Not
used
Set wind
threshold
Association
Wind
Configuration
Wireless
transmission
signal
The sensor must be activated before
being used for the first time.
To do this, press and hold the and
buttons for 2 seconds.
The display screen will turn on.
> 2s
The wind sensor switches
automatically into energy
saving mode after 30 seconds of
inaction.
Before each use, «activate» the sen-
sor by pressing any button.
3. Activation
4. Association
1 2
> 2s > 2s
1234
... ... ...
> 3s
1234
TYXIA TYXIA
- Set the receiver(s) to
association wait mode.
- Press and hold the button for 2
seconds.
- The symbols and are displayed
while the device searches for receivers.
- The detected receiver number is displayed
on the screen,
and the symbol «NEW» appears.
- Press and hold the button to confirm
the association.
- On the receiver(s) check that the association was
successful. The receiver LED stops flashing
and the shutter briefly operates twice.
Display when the
sensor has detec-
ted more than 9
receivers.
Display when the sensor
has not detected any recei-
vers > Switches to «Manage
networks» mode (see §10)
4
OK
OFF
1234
TYXIA
Lithium battery - AA
cannot be replaced
Lithium battery life: 10 years
868,7 MHz -> 869,2 MHz
Maximum radio power < 10 mW
Receiver category: 2
100 -> 300 m
IP IPx4
-10°C / +70°C
-10°C / +60°C
260 x 104 x 130 mm
www.deltadore.com
5. Set wind threshold
> 2s
10 km/h
threshold Slight breeze
20 km/h
threshold Gentle breeze
30 km/h
threshold Moderate breeze
(default value)
40 km/h
threshold Fresh breeze
50 km/h
threshold Strong wind
66 km/h
threshold Very strong wind
To protect the shutter or blind equipment, select the wind threshold
recommended by the manufacturer.
- Press and hold the
button for 2 seconds.
- The symbol will flash.
- Press and hold the
button to select the next
value.
For safety reasons, the wind sen-
sor cannot be neutralised.
The mode is exited
automatically after
5 seconds of inaction.
7. Display of Wind Sensor setting
6. Test
The mode is exited automatically after 5 seconds of inaction.
> 2s
To test that the sensors are operating correctly.
- The sensor simulate the setting threshold and sends the required com-
mand to the receiver.
- Press and hold the
button for 2 seconds
then the button.
You can view the saved setting
1
4
2
3
- Remove the 2
protective
covers
- Replace
the protec-
tive
covers
- Straighten the
sensor
by positioning
the cups
horizontally
- Attach the sen-
sor (screws and
plugs included)
Cups
8. Installation
To remove a receiver associated with
the sensor, follow these instructions:
> 2s
1
1
2
> 2s
> 2s
- Press and hold the
button for 2 seconds.
- Press and hold the button for 2 seconds.
- The receiver number flashes for 2 seconds.
- The sensor display switches off, and the
association between
receiver 1 and the sensor is now removed.
«Manage networks» mode
- The device runs a search for associated
receivers.
- Press the button repeatedly to select
the receiver to be removed.
The associated blind will operate briefly.
9. Remove an association 10. Remove all associations
To remove all receivers associated with the sensor,
follow these instructions:
- Press and hold
the button
for 2 seconds.
- Press and hold the button
for 2 seconds.
- The display will show
then switch off.
> 2s > 2s
8.1 Location
Install the Wind sensor near
the associated blinds.
The wind sensor cups must be
positioned horizontally and facing
downwards.
8.4 Maintenance and cleaning
To ensure optimum operation of the wind/sun sensor:
• Regularly check that the wind sensor is rotating freely.
• Ensure that the sun sensor is free of dust.
If necessary, clean the cover with a damp cloth.
(Do not use abrasive cleaning products or chemical
solutions which could damage the surface of the cover.)
90°
90°
8.2 Assembly
Adapt the hinged mount to your installation.
8.3 Installation
H O2
Press and release the button to
display the value set for the wind sensor.

Especificaciones del producto

Marca: Delta Dore
Categoría: No categorizado
Modelo: CV wind

¿Necesitas ayuda?

Si necesitas ayuda con Delta Dore CV wind haz una pregunta a continuación y otros usuarios te responderán


No categorizado Delta Dore Manuales

Delta Dore

Delta Dore Tyxal+ REP Manual de Usario

25 Agosto 2024
Delta Dore

Delta Dore Tyxal+ DCP Manual de Usario

24 Agosto 2024
Delta Dore

Delta Dore CV wind Manual de Usario

24 Agosto 2024
Delta Dore

Delta Dore Tycam 2100 BRE Manual de Usario

23 Agosto 2024
Delta Dore

Delta Dore TYXAL+ DME90 Manual de Usario

20 Agosto 2024
Delta Dore

Delta Dore Tyxal+ DOS Manual de Usario

18 Agosto 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024