Denon DN-470A Manual de Usario

Denon receptor DN-470A

Lee a continuación 📖 el manual en español para Denon DN-470A (5 páginas) en la categoría receptor. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/5
User Guide English (3–6)
Guía del usuario Español (7–10)
Guide d’utilisation Français (11–14)
Guida per l’uso Italiano (15–18)
Benutzerhandbuch Deutsch (19–22)
Appendix English (23)
3
User Guide ( )English
Introduction
Thank you for purchasing the DN-470A. At Denon Professional, performance and reliability
mean as much to us as they do to you. That’s why we design our equipment with only one
thing in mind—to make your performance the best it can be.
Box Contents
DN-470A
(2) 6-Pin Euroblock Connectors
(4) 4-Pin Euroblock Connectors
Power Cable
Rack Ears with Screws
User Guide
Safety & Warranty Manual
Support
For the latest information about this product (documentation, technical specifications, system
requirements, compatibility information, etc.) and product registration, visit denonpro.com.
For additional product support, visit denonpro.com/support.
4
Features
Front Panel
1. Power Switch: Press this switch to power DN-470A on or off.
2. Level Knobs: Turn these knobs to set the output level for each channel.
3. Signal/Clip/Protection LEDs: These lights will illuminate different colors to show the
signal status of each channel input:
Signal LED: The input’s Signal LED will be lit green when it is receiving a signal at
an optimal level.
Clip LED: The input’s Clip LED is “peaking” when the LED is lit red (higher than 0 dB).
Turn its Level knob counter-clockwise or reduce the volume of the source to prevent
“clipping” (distortion).
Protection LED: If the Protection LED turns red, the unit is in heat protection mode
and will not output sound. To restore sound output, reduce the temperature by making
sure there is good ventilation and by decreasing the signal level.
4. Air Intake Vents: Keep the vents clear from obstructions to allow air to flow through the
front grill for proper performance.
Rear Panel
1. Power Inlet: Use the included power cable to connect this input to a power outlet.
2. Fuse: If the unit’s fuse is broken, lift this tab to replace the fuse. Replace it with a fuse with
an appropriate rating. Using a fuse with an incorrect rating can damage the unit and/or fuse.
3. Inputs: Use Euroblock connectors to connect these channel inputs to your audio sources.
Each channel has a ground (G), cold/negative (), and hot/positive (+) connector. Make
sure the wiring of each device matches each connection.
4. Outputs: Use Euroblock connectors to connect these channel outputs to your
loudspeakers. Each channel has a switch for 70V and 100V. Make sure the wiring of each
loudspeaker is done properly for each output.
Important: Connect only one type of speaker to each amplifier output. Use only 70V/100V
speakers designed with step-down transformers on the 70V/100V outputs. Do not connect
a low-impedance speaker (4Ω) to the 70V/100V output terminals, as this may result in
damage to your amplifier and/or speaker.
5. Operation Mode Switch: Select the operation mode (70V or 100V) for each channel’s
output by moving the dip-switches to the desired position.
6. Exhaust Vents: Air from the front intake flows through the unit and exits here. For proper
performance, do not block the air vent.
1
1
1
11
2
2
2
222
2
2
222
2
2
222
2
2
22
3
3
3
333
3
3
33
4
4
4
44
1
1
1
1
5
5
5
5
PRESET
1
1
1
11
2
2
2
22
3
3
3
334
4
4
446
6
6
66
5
5
5
55

Especificaciones del producto

Marca: Denon
Categoría: receptor
Modelo: DN-470A

¿Necesitas ayuda?

Si necesitas ayuda con Denon DN-470A haz una pregunta a continuación y otros usuarios te responderán




receptor Denon Manuales

receptor Manuales

Últimos receptor Manuales