Denver DAB-35 MK2 Manual de Usario

Denver Radio DAB-35 MK2

Lee a continuación 📖 el manual en español para Denver DAB-35 MK2 (7 páginas) en la categoría Radio. Esta guía fue útil para 15 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/7
DAB Radio Signal
Please notice that DAB signal can be weaken MUCH depending on the type of
building you are living in. (fx. It can be hard to catch proper signal when being in
a concrete building.)
Signal can also be different in different areas of the country. Please check your
local transmitter to get the best signal in your area.
Vær opmærksom på at det kan påvirke DAB signalet MEGET hvilken type
bygning man bor i. Det kan f.eks. være svært at få et ordentligt signal hvis man
bor i beton byggeri.
Der er også forskel på hvor god dækningen er i forskellige områder. Tjek nyeste
dækningskort på www.dabradio.dk under ”hvad er digital radio”.
DAB-35MK2
Instruction manual
ENG-1 ENG-2
BASIC OPERATION - GETTING STARTED
Press the button to turn the unit on, it will automatically enter into the DAB mode and STANDY
perform auto scan function. During the scan, the display show “Scanning…” together with a slide bar
that indicates the progress of the scan and the amount of stations that have been found so far. (F.2)
Once the scan has finished, the radio will select the first alphanumerically found station. You can
now press / buttons to explore the found stations followed by pressing the button to ▼ ▲ SELECT
select listening to the stations.
Note: If there is no stations found after auto scan, the radio will display "Full Scan", you can now
press / buttons to select “Full scan” or “Manual tune” for stations, and press button to ▼ ▲ SELECT
finally confirm.
F.1 F.2
MENU Tree as below:
Mode Mode
DAB
DAB Menu
Full Scan
Manual Tune
Prune
System
FM
Menu Menu
System Menu
Time
Sleep
Backlight
Factory Reset
SW version Backlight Menu
Backlight Low/ Medium/ High
Time Menu
Set Time/Date hh:mm/DD-MM-YYYY
Auto Update Update from Any/Update from DAB/Update from FM/ No Update
Set 12/24 hour 12/24
Set Date Format DD-MM-YYYY/MM-DD-YYYY
Sleep Menu
Sleep Off /10/20/30/60/70/80/90minutes
FM Menu
Scan Setting All station/Strong stations only
Audio Setting Stereo Allowed/Forced mono
System
17
PARTS
Front view Rear view
SWITCHING YOUR RADIO ON FOR THE FIRST TIME
AC Operation
1. Insert the DC power jack of AC/DC adaptor to the DC input socket located at the rear of the
radio.
2. Plug the AC/DC Adaptor to the AC mains outlet.
3. Press the to turn the radio on.STANDBY
Remarks: If the AC Adaptor voltage is over than 6V, it will possible make the line damage.
DC (battery) operation
1. Ensure the AC/DC adaptor is disconnected from the radio and AC mains.
2. Installed the batteries (4×1.5V UM3/AA battery) into the battery compartment.
3. Press the to turn the radio on.STANDBY
Remarks: To obtain the best performance in DC operation, the use of alkaline batteries is highly
recommended.
Menus:
The following controls are used to move about the menu tree to choose and select the required
settings:
Press and hold button to enter into the “MENU”. Press the or MENU/INFO TUN/CH TUN/CH
button to navigate the desire option, then press button to confirm.SELECT
1. SPEAKER
2. STANDBY BUTTON
3. MODE BUTTON
4. LCD DISPLAY
5. TUN/CH▼ BUTTON
6. TUN/CH▲ BUTTON
7. ALARM/SNOOZE BUTTON
8. MENU/INFO BUTTON
9. VOLUME CONTROL
10. SELECT BUTTON
11. PRESET BUTTON
12. ROD ANTENNA
13. DC INPUT SOCKET
14. RATING LABEL
15. HEADPHONE JACK
16. BATTERY DOOR
17. AC/DC ADAPTOR
No function
DENVER DAB-35MK2 DENVER DAB-35MK2

Especificaciones del producto

Marca: Denver
Categoría: Radio
Modelo: DAB-35 MK2

¿Necesitas ayuda?

Si necesitas ayuda con Denver DAB-35 MK2 haz una pregunta a continuación y otros usuarios te responderán




Radio Denver Manuales

Radio Manuales

Últimos Radio Manuales