DeWalt DWFP12658 Manual de Usario
Lee a continuación 📖 el manual en español para DeWalt DWFP12658 (48 páginas) en la categoría Grapadora. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/48
1 - ENG
DWFP12658
ROOFING COIL NAILER
CLOUEUSE POUR TOITURE À CLOUS EN BOBINE
CLAVADORA PARA TECHADO A RESORTE
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-D WALTe • www.dewalt.com
9R199590RA
INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
INSTRUCTIONS DE FONCTIONNEMENT,
CENTRES DE SERVICE, POLITIQUE DE
GARANTIE. AVERTISSEMENT : LISEZ CES
INSTRUCTIONS AVANT D'UTILISER L'APPAREIL.
2 - ENG
• Actuating tool may result in flying debris, collation
material, or dust which could harm operator’s eyes.
Operator and others in work area MUST wear safety
glasses with side shields. These safety glasses must
conform to ANSI Z87.1 requirements (approved glasses
have “Z87” printed or stamped on them). It is the
employer’s responsibility to enforce the use of eye
protection equipment by the tool operator and other
people in the work area. (Fig. A)
• Alwayswearappropriate personalhearingandother
protection during use. Under some conditions and
duration of use, noise from this product may contribute
to hearing loss. (Fig. A)
• Useonlyclean,dry,regulatedair.Condensationfrom
an air compressor can rust and damage the internal
workings of the tool. (Fig. B)
• Regulate air pressure. Use air pressure compatible
with ratings on the nameplate of the tool. [Not to
exceed 120 psi (8.3 bar).] Do not connect the tool to a
compressor rated at over 200 psi. The tool operating
pressure must never exceed 200 psi even in the event of
regulator failure. (Fig. C)
• Only use an air hose that is rated for a maximum
working pressure of at least 150 psi (10.3 bar) or
150% of the maximum system pressure, whichever is
greater. (Fig. D)
• Do not use bottled gases to power this tool. Bottled
compressed gases such as oxygen, carbon dioxide,
nitrogen, hydrogen, propane, acetylene or air are not
70 psi
4.9 bar
Fig. C
Fig.B
Fig. A
Fig. D
IMPORTANT SAFETY INSTRUCTIONS
FOR PNEUMATIC TOOLS
SAVE THESE INSTRUCTIONS
WARNING: When using any pneumatic tool, all safety precautions, as outlined below,
should be followed to avoid the risk of death or serious injury. Read and understand all
instructions before operating the tool.
DEFINITIONS - SAFETY GUIDELINES
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
DANGER: will Indicates an imminently hazardous situation which, if not avoided,
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may
result in minor or mod er ate injury.
NOTICE: Used without the safety alert symbol indicates a situation which, if not
avoided, may property damage. result in
3 - ENG
for use with pneumatic tools. Never use combustible
gases or any other reactive gas as a power source for this
tool. Danger of explosion and/or serious personal injury
may result. (Fig. E)
• Use couplings that relieve all pressure from the tool
when it is disconnected from the power supply.
Use hose connectors that shut off air supply from
compressor when the tool is disconnected. (Fig. F)
• Disconnect tool from air supply when not in use.
Always disconnect tool from air supply and remove
fasteners from magazine before leaving the area or
passing the tool to another operator. Do not carry
tool to another work area in which changing location
involves the use of scaffoldings, stairs, ladders, and
the like, with air supply connected. Do not make
adjustments, remove magazine, perform maintenance
or clear jammed fasteners while connected to the
air supply. If the contact trip is adjusted when the tool
is connected to the air supply and nails are loaded,
accidental discharge may occur. (Fig. G)
• Connect tool to air supply before loading fasteners
to prevent an unintentional fastener discharge during
connection. The tool driving mechanism may cycle
when the tool is connected to the air supply. Do
not load fasteners with the trigger or the contact trip
depressed to prevent unintentional driving.
• Do notremove,tamper with,or otherwisecause the
tool, trigger, or contact trip to become inoperable.
Do not tape or tie trigger or contact trip in the on
position. Do not remove spring from contact trip. Make
daily inspections for free movement of trigger and contact
trip. Uncontrolled discharge could result.
• Inspect tool before use. Do not operate a tool if
any portion of the tool, trigger, or contact trip is
inoperable, disconnected, altered, or not working
properly. Leaking air, damaged parts or missing parts
should be repaired or replaced before use. Refer to
Repairs. (Fig. H)
• Donotalterormodifythetoolinanyway.(Fig. I)
• Alwaysassumethatthetoolcontainsfasteners.
• Donotpointthetoolatco-workersoryourselfatany
time. No horseplay! Work safe! Respect the tool as a
working implement. (Fig. J)
• Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control. When tool is not in use, it should be locked
in a safe place, out of the reach of children.
• Removefingerfromtriggerwhennotdrivingfasteners.
• Never carry tool with finger on trigger. Accidental
discharge could result. Using the trigger lock-off will
prevent accidental discharge.
Fig. E
Fig. F
Fig. I
Fig. J
Fig. G
Fig. H
Especificaciones del producto
| Marca: | DeWalt |
| Categoría: | Grapadora |
| Modelo: | DWFP12658 |
¿Necesitas ayuda?
Si necesitas ayuda con DeWalt DWFP12658 haz una pregunta a continuación y otros usuarios te responderán
Grapadora DeWalt Manuales
1 Octubre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
16 Septiembre 2024
Grapadora Manuales
- Grapadora Bosch
- Grapadora Silverline
- Grapadora Makita
- Grapadora Vonroc
- Grapadora Ryobi
- Grapadora Rapoo
- Grapadora Florabest
- Grapadora Targus
- Grapadora Sencor
- Grapadora Metabo
- Grapadora Parkside
- Grapadora Milwaukee
- Grapadora Hikoki
- Grapadora Sun Joe
- Grapadora President
- Grapadora Craftsman
- Grapadora Meister
- Grapadora Porter-Cable
- Grapadora Aqua Joe
- Grapadora Stihl
- Grapadora Rapid
- Grapadora Surtek
- Grapadora MSW
- Grapadora CTA Digital
- Grapadora Mannesmann
- Grapadora Smart365
Últimos Grapadora Manuales
15 Octubre 2024
2 Octubre 2024
23 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024