Dimplex DAB20E Manual de Usario

Dimplex No categorizado DAB20E

Lee a continuación 📖 el manual en español para Dimplex DAB20E (3 páginas) en la categoría No categorizado. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3



Contact Details



Pleasenotethat some contact ofthe details on 

thisPDFdocumentmaynotbe current.



Pleaseuse  the following detailsifyouneedto

contactus:



Telephone:0844 879 3588

Email:customer.services@gdcgroup.co.uk



The widecustomer alsosupportsection websiteofour  features a

rangeof ofinformationwhichmaybe use availabletoyouandis 

24 ahours day.Itincludes:



• Operating   and installation instructions

• Easy       ‘How to use’ guides for storage heaters

• Service  and repairs

• Wheretobuyourproducts

• Literature downloads

• Heating  requirement calculator



 ‐Visit www.dimplex.co.uk/support

A division of GDC Group Ltd

Millbrook House Grange Drive Hedge End Southampton SO30 2DF

www.dimplex.co.uk

istered No: 1313016 En

land

VAT GB 287 1315 50004

EEE Producer Registration Number –

WEE/GE0057TS

Paper from sustainable sources

Installation and Operating Instructions

Dimplex Air Curtain - Single Phase Conversion Kit - CAB1PN

Suitable for use with the CAB10E, CAB15E & DAB10E (Surface & Recessed)

08/19538/0 Issue 4

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

IMPORTANT SAFETY ADVICE

ENSURE THE APPLIANCE IS EARTHED.

This work should only be carried out by a competent

electrician.

Always disconnect the supply before working on the

product.

Ensure the supply cables are of adequate current

carrying capacity and are protected by a suitable

fuse.

Ensure all wiring is ﬁ xed clear of all moving parts and

heat sources.

This kit is designed for use with DAB15 models.not

This conversion kit consists of:

8 x 100mm x 2.5mm tie wraps

4 x Moss Plastic tie wrap clips

2 x Neutral link cable

1 x Live link cable

The instructions for the conversion kit should be

read in conjunction with the ‘Dimplex Air Curtain’

Instructions. All ‘Safety Advice’ to be heeded before

ﬁ tting this kit.

General

The CAB10E, CAB15E and DAB10E are primarlity

designed for 400V~ 3P&N 50Hz operation, however in

the instance where it is not possible to utilise a 3-phase

supply, the units can be de-rated to a ½ heat stiing for

operation via a 230V~ 1P&N 50Hz supply.

Procedure

1. remove the outlet grille assemblies and, where

necessary, the bottom panel and inlet grille to gain

access to the element banks and terminal blocks as

shown in Fig. 1 below.

2. Remove the ﬁ rst half heat (H1) star connection link

cable from both sides of each elmenet bank (Fig. 2 shows

the bottom red (H1)) star connection link cable replaced

with the supplied neutral star connection link cable.

3. Fix the push on clips (two on

either side) to the inside of the

pressure plate as shown in Fig.

1 (the supplied push on clips

are a press ﬁ t into their ﬁ xing

holes (ø3.5mm). Proceed

to attach the neutral star link

connection cable to the push

on clips using the tie wraps as

shown in Fig. 3 below.

Note: Due to extra cable length (for CAB15E) it is

necessary to loop the slack cable in the pressure plate and

secure it using a supplied tie wrap as shown in Fig. 1.

4. Connect the brass ferrule end of the neutral link cable

into the N of the terminal block (along with the Neutral of

the single phase supply) as shown in Fig. 4.

5. Also shown in Fig. 4 is the supplied (brown) Live link

cable, this should be linked from L1 (with connection of

Live from single phase supply) to L2 & L3.

The earth cable is connected as normal within the

terminal block (ensure the supply cable is ﬁ xed

appropriately within the back panel using the correct

sized gland).

6. Check all switch settings operate, as stated within

the evaluation table (overleaf). Note: H2 should still be

connected (as per remote switch connection instruction

manual) even though it will not be utilised (this still allows

a ½ heat setting when switched to full heat rather than no

heat at all).

Figure 1.

Figure 3.

Figure 4.

BLUE

RED

Once the above loadings and switch settings have been

conﬁ rmed as acceptable, proceed to replace the grille

assemblies, and where necessary, the bottom panel.

For reference purposes a full wiring schematic is detailed

above.

Please retain your receipt as proof of purchase.

Especificaciones del producto

Marca:	Dimplex
Categoría:	No categorizado
Modelo:	DAB20E
Color del producto:	Meerkleurig
Peso.:	9700 g
Ancho:	1194 mm
Profundidad:	660 mm
Altura:	406 mm
Peso del embalaje:	10900 g
Ancho del embalaje:	673.1 mm
Empaquetadura en profundidad:	165.1 mm
Altura del embalaje:	1206.5 mm
Edad recomendada (mín.):	3 jaar
Tipo de embalaje:	Gesloten doos
País de origen:	China
Certificación:	EN 71, CPSIA
Material:	Kunststof
Género propuesto:	Jongen/meisje
Numero de piezas:	2 stuk(s)
se requiere ensamblaje:	Nee
Volumen de embalaje:	134076.9093 cm³
Advertencia de TSD de la UE:	Not for children under 36 months, Only for domestic use
Artículo ordenable:	Nee
unidad de facturación:	Nee
Idiomas del manual (formato ISO 639):	Multi
Tipo de unidad comercial:	Klant enkele eenheid
Unidad de envío:	Nee
Muestras de embalaje (formato ISO 639):	Multi
Estacional:	Permanent
(cdm) Capacidades desarrolladas:	Imagination, Sharing
(cdm) Grupos destinatarios:	Peuters en kleuters
(cdm) Uso adicional:	Binnen
(cdm) Presencia de los padres:	Aanbevolen
Código de apalancamiento:	95030095