Dimplex WFC3NS Manual de Usario

Dimplex No categorizado WFC3NS

Lee a continuación 📖 el manual en español para Dimplex WFC3NS (4 páginas) en la categoría No categorizado. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Installation and Operating Instructions

Dimplex Wall-mounted Fan Convector 08/18724/0 Issue 0

Models : WFC 3NB and WFC 3NS

350mm min

571mm 120mm

350mm

Dimensions

Model(s) Specification

WFC 3NB 3kW, Switch, Thermostat & Neon - Black

WFC 3NS 3kW, Switch, Thermostat & Neon - Silver

Fig. 1

Installation

Before undertaking installation work, ensure the electricity supply

is disconnected from any relevant fixed wiring.

Supply cable is not provided with this appliance, and a competent

electrician should therefore install it.

The appliance must be fitted horizontally with the cable or conduit entry

at bottom right. It should be mounted such that the underside is at least

350mm above the floor and the top of the heater is 150mm below any

overhanging shelf or obstruction.

This heater must be used on an A.C.~ supply only and the voltage

marked on the heater must correspond to the supply voltage.

To comply with the I.E.E. Wiring Regulations, the appliance must be

earthed; the supply circuit must be adequate for the input of the

appliance, and the circuit protected by a suitable 13A fuse. A suitable

termination to the fixed wiring of the premises must be provided adjacent

to the final position of the appliance. In this instance, such a termination

can be a double-pole switch with a contact separation of at least 3mm in

all poles.

The heater must not be located immediately below a socket-outlet.

Electrical

WARNING : THIS APPLIANCE MUST BE EARTHED.

After ensuring the electricity supply is not live, electrical connections can

be made, either to an adjacent double-pole switch having a contact

separation of at least 3mm in all poles or to a plug-top for use in a

standard 13A socket.

If the latter: Connect Green and Yellow wire to plug terminal marked E

or Green or Green and Yellow. Connect Blue wire to plug terminal

marked N or Black. Connect Brown wire to plug terminal marked L or

Red.

Refit cover, first hooking top over the back of the unit and then securing

the bottom by refitting the two screws under the bottom edge. The

appliance is now ready for use and the electricity supply can be

reinstated.

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.

IMPORTANT SAFETY ADVICE

WARNING – THIS APPLIANCE MUST NOT BE USED IN A

BATHROOM.

WARNING – DO NOT USE THIS HEATER IN THE IMMEDIATE

SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING

POOL.

WARNING – THIS HEATER MUST NOT BE LOCATED

IMMEDIATELY BELOW A FIXED SOCKET OUTLET.

DO NOT USE THE HEATER UNTIL IT IS WALL MOUNTED

CORRECTLY.

The heater carries a warning 'Do Not Cover' to alert the user

to the risk of overheating that exists if the heater is

accidentally covered.

NEVER cover or obstruct in any way the air inlet slots at the

front of the heater or the heat outlet slots in the base of the

heater.

Keep combustible materials such as drapes and other

furnishings clear from the front of the heater. Do not use

heater to dry your laundry.

If young children, the aged, or infirm are likely to be left in

the vicinity of the heater, we advise that adequate

precautions should be taken. We recommend that a guard

be fitted to ensure contact with the heater is avoided and

objects cannot be inserted into the product.

If you use this heater in conjunction with a thermal control, a

programme controller, a timer or any other device which

switches on the heater automatically, remember to observe

all safety warnings at all times.

Do not use where excessive dust or moisture is present.

For further information, please contact our guard supplier

direct on Tel. No. 01603 667957, or in the case of difficulty or

for further advice contact the Customer Helpline.

Operation

Fixing dimensions

cable or

conduit entry

35mm

510mm

571mm

280

Ø10m

shel

150mm min

350mm min.

8mm

350mm

6mm

Fig. 2 - Controls &

Control Panel Layout

Fig. 3

Procedure

The Dimplex WFC 3NB and WFC 3NS have a total loading of 3 kW.

They are fitted with two control knobs and a pilot light. The air inlet is in

the front panel, and the outlet on the underside.

Release the front cover from the unit by undoing the two screws under the

bottom edge. The upper knob operates a six-position switch, giving a choice of

operating characteristics as follows :

Carefully remove cover by pulling bottom-front forward, and then lift to

release top from retaining slots.

▬ Off

Mark screw fixing positions on wall in accordance with the dimensions

shown on the diagram. The unit must be secured to the wall with four

screws through the holes provided. The two upper holes are keyhole

shaped to enable the two upper screws to be positioned first. The unit can

then be hung on these screws while the two lower screws are positioned.

Before finally tightening all four screws, ensure the unit is truly horizontal.

. ▬ 1kW of heat, low fan speed

▬ 2kW of heat, medium fan speed.

▬ 3kW of heat, high fan speed.

Fit a 3 core 1.5 square millimetre flexible cord through the cable entry

bush, connect wires to the appropriate terminals and tighten cable clamp.

Alternatively the heater may be connected with conduit through the base

after removing the knockout containing the cable entry bush (see Fig. 4

Wiring Diagram).

▬ Fan only, low speed.

▬ .Fan only, high speed

The lower knob operates a thermostat which enables the temperature of

the room to be regulated.

Wiring Diagram

The pilot light indicates when the appliance is connected to the electricity

supply.

Component Wire

A. Cross flow fan 1. White 1mm

2 Additionally, a cut-out is incorporated in the unit which will switch the

electricity supply off if for any reason the appliance overheats.

B. Cut –out 2. Pink 1mm

C. Selector switch 3. Violet 1mm

2 If the cut-out has operated because the air flow has been obstructed in

some way, the heater will switch on once the obstruction has been

removed. If the cut-out continues to operate intermittently the heater

should be switched off and a service agent should be called.

D. Neon light 4. Brown 1mm2

E. Thermostat 5. Red 1mm

F. Resistor 6,7. Blue 1.5mm2

G. Earth Terminal 8,9. Red 1.5mm

H. Terminal Block 10. Grey 0.75mm

2 To control the room temperature, set the mark on the thermostat knob to

the required temperature on the visually graduated scale (see Fig. 2).

The thermostat will monitor continuously the temperature of the air

returning to the inlet grille, and the appropriate heater element(s) will be

selected automatically to achieve or maintain the chosen level efficiently

and economically.

J. Cable Clamp

Fig. 4

General Cleaning

Mesh

Filter

Retaining

Wires

Air Inlet

Grille

WARNING :

BEFORE UNDERTAKING ANY MAINTENANCE OR CLEANING WORK

ON THE APPLIANCE, IMMEDIATELY DISCONNECT THE

ELECTRICITY SUPPLY EITHER BY SWITCHING OFF AT THE

ADJACENT DOUBLE POLE SWITCH OR BY REMOVING THE PLUG

FROM THE SOCKET.

The outside of the appliance should be wiped over with a soft damp cloth

and then dried. Do not use detergents or abrasives.

The filter should be cleaned by gently passing the soft brush attachment

of a vacuum cleaner over the front grille.

Service and Repair

THE INTERNAL CLEANING AND MAINTENANCE WORK SHOULD

ONLY BE UNDERTAKEN BY COMPETENT PERSONS WITH

EXPERIENCE OF REPAIRING DOMESTIC ELECTRICAL APPLIANCES

AND IN FULL KNOWLEDGE OF THE POSSIBLE HAZARDS

INVOLVED.

To ensure the appliance operates efficiently, the following maintenance

should be undertaken periodically. The cover should be removed and

refitted as detailed under ‘Procedure’.

Fig. 5

• Fan Blades : These should be cleaned by using the soft brush

attachment of a vacuum cleaner. Care should be taken not to

damage the blades.

• Filter : The filter can be removed completely for cleaning, but

generally provided this is cleaned frequently as detailed above, this

should not be necessary. Where removal of filter is required for

cleaning, the filter retaining wires can be removed, allowing the mesh

and the filter to be taken out (see Fig. 5).

• General : With the cover removed, opportunity should be taken to

remove any accumulations of dust from within the unit.

• Bearings : Fan and motor bearings should be given one or two (not

more) drops of low viscosity oil (e.g. sewing machine oil)

approximately every 12 months.

Especificaciones del producto

Marca:	Dimplex
Categoría:	No categorizado
Modelo:	WFC3NS
Color del producto:	Zwart
Interruptor encendido / apagado:	Ja
Ajustable en altura:	135 mm
Mostrar.:	LCD
Diagonal de la pantalla:	21.3 "
Resolución:	1600 x 1200 Pixels
Pantalla táctil:	Nee
Relación de aspecto original:	4:3
Ángulo de visión, horizontal:	178 °
Ángulo de visión, vertical:	178 °
Relación de contraste típica:	1000:1
Posicionamiento en el mercado:	Bedrijf
Rango de frecuencia horizontal:	24 - 92 kHz
Rango de frecuencia vertical:	50 - 85 Hz
Puerto(s) VGA (D-Sub):	1
Puerto DVI:	Ja
Opción de montaje de bloqueo de cable:	Nee
Altavoces incorporados:	Nee
Consumo de energía (en espera):	- W
Certificación:	TCO’99, TÜV/GS, TÜV/Ergo, ISO 13406-2 (Pixelfehlerklasse II), TÜV-S, UL, cUL, FCC-B (ICES), CB, CE, ICES-003B, NOM, ENERGY, ENERGY STAR, GOST-R, Hygienic, SASO, KTL/MIC, BSMI, CCC, PSB, C-TICK, WEEE, RoHS
Pantalla, número de colores.:	16.78 miljoen kleuren
tipo HD:	Niet ondersteund
Corriente de entrada:	Ja
3D:	Nee
Tecnología de visualización:	LCD
Tiempo de respuesta:	16 ms
Tamaño de píxel:	0.27 x 0.27 mm
Resoluciones de gráficos compatibles:	1600 x 1200 (UXGA)
Interfaz de montaje en panel:	- mm
Brillo (típico):	300 cd/m²
relación de aspecto:	4:3
Sintonizador de TV integrado:	Nee
Cámara integrada:	Nee
Profundidad (sin base):	63 mm
Altura (sin base):	363 mm
Ancho (sin base):	468 mm
Peso (sin base):	5400 g
Conecta y reproduce:	Ja
Ancho del dispositivo (con soporte):	468 mm
Dispositivo de profundidad (con soporte):	315 mm
Altura del dispositivo (con soporte):	404 mm
Peso (con soporte):	9200 g
Número de puertos descendentes USB tipo A:	5
Versión concentrador USB:	2.0
Consumo de energía (PowerSave):	3 W
Cliente ligero instalado:	Nee
Tipo de panel:	TFT
Giratorio:	Ja
Giratorio horizontalmente:	-135 - 135 °
Área de imagen:	Mat
Puertos DVI-I:	1
Tamaño de imagen (horizontal):	432 mm
Tamaño de imagen (vertical):	324 mm
Bisagra:	Ja
Esquina pivotante:	0 - 90 °
voltaje-de-entrada-de-CA:	100 - 240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Consumo de energía (típico):	57 W
Temperatura de funcionamiento (TT):	0 - 40 °C
Humedad relativa de funcionamiento (VV):	10 - 90 procent
Rango de ángulo de inclinación:	-5 - 20 °
ajustes de inclinación:	Ja