Doepfer A-119 Manual de Usario

Lee a continuación 📖 el manual en español para Doepfer A-119 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
doepfer System A - 100 Ext. Input / Envelope Follower A-119
1
1. Introduction
Module A-119 (External Input / Envelope Follower)
is designed to allow external audio signals to be
integrated into the System A-100. It comprises a pre-
amp, envelope follower, and comparator.
The pre-amp has two inputs: an unbalanced input for
line level signals, with a gain factor of from 0 to 20, and
a balanced input with a gain factor of from 0 to 500,
for insertion of low level signals, for instance from a
microphone or electric guitar.
The Envelope Follower reads the signal level of the
input, and puts out a proportional voltage as an enve-
lope at its own output (see chapter 3. How it works).
The comparator generates a gate signal whenever the
input goes above an adjustable trigger threshold (see
chapter 3. How it works).
Three LEDs help you keep track of overload, the
envelope, and the gate signal.
Asym.
In
Over-
Load
Gate
Out Threshold
Gain
A-119
Ext. In.
Symm. In
Envelope
Out
Audio
Out
A-119
Ext. Input / Envelope Follower
System A - 100 doepfer
2
2. A-119 - Overview Controls and indicators:
1 Gain : Control for input signal level
2 Over-Load : LED overload warning
3 % LED : Envelope level indicator at (output )
4 LED : Gate indicator (output &)
5 Thres. : Trigger threshold control
In / Outputs:
! Asym. In : Unbalanced input for line-level audio
" Symm. In : Balanced input for mic or instrument-
level signals (6.3 mm jack socket)
§ Audio Out : Output for pre-amped audio signal
$ Audio Out : ditto, linked with output §
% Env. Out : Envelope output
& Gate Out : Gate output
A-119
Ext. In.
Audio Out
Envelope
Out
Gain
Over-
Load
Thres.
Asym. In
Ext. Input / Env. Follower
0 10
0 10
Gate Out
Symm.
In
doepfer System A - 100
Ext. Input / Envelope Follower
A-119
3
3. The Envelope Follower: how it works
The external audio signal (see Fig. 1a) is patched into
input ! or ", depending on its level. It is amplified by
an amount set by the gain control 1, brought up to
A-100 internal operating level, and can then be output
from audio outs § and/or $.
To produce envelope and gate signals, the amplified
signal is put through a full-wave rectifier, so that the
internal signal output has only positive voltages (see
Fig. 1b).
Next, the rectified signal passes through a 50 Hz low
pass filter, and is sent to envelope output %.
H With input frequencies of less than 50 Hz,
patch the envelope output % into an A-170
slew limiter, set to a time constant of greater
than 20 ms, to avoid remnants of the signal
being audible in the envelope.
The signal at the envelope output is compa-
red with the adjustable trigger threshold (T in
Fig. 1c), to produce gate signals, available at
output &.Fig. 1: The envelope follower: how it works
0
0
0
0
a
b
c
d
T

Especificaciones del producto

Marca: Doepfer
Categoría: No categorizado
Modelo: A-119

¿Necesitas ayuda?

Si necesitas ayuda con Doepfer A-119 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Doepfer Manuales

No categorizado Manuales

Últimos No categorizado Manuales