Dormakaba C200 Manual de Usario

Dormakaba No categorizado C200

Lee a continuación 📖 el manual en español para Dormakaba C200 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Installation Instructions: C200 Cylindrical

DORMA-C200 series 10-2021T91907_A 1

www.dormakaba.us

 Installation instructions

Fig.

Fig.

. Overview

. Position template.

. Bore two holes and install latch.

.. Install the latch so that the bevel

on the latchbolt faces the strike.

.. Adjust the outside rose assembly

so that the chassis is centered in

the door. Install the chassis from

the outside of the door.

.. Install the inside liner, through-

bolts, rose, lever and strike.

.. Fold the template and place it in

position on the high edge of the

door bevel.

.. Mark the drill points.

.. Bore a -/" (54 mm) diameter hole from both

sides of the door, to the center of the door.

.. Drill a " ( mm) diameter hole from the edge of

the door that intersects the -/" (54 mm) hole.

.. Mortise the door edge for the latch face.

.. Install the latch through the " ( mm) diameter

hole. For drive-in latches, use a rubber mallet. Latch

tabs should project into the -/" (54 mm)

diameter hole.

.. Check the door swing.

NOTE: For factory prepared doors only.

NOTE: The suggested height from the

floor to centerline of the lock is -/"

( mm). If steel frames are used, the

latch center-line must be in line with the

center of the strike preparation.

NOTE: Make sure the locking pin locks into the

rose liner.

NOTE: Locksets will fit -/" (35 mm) to "

( mm) thick doors.

. Install liner, through-bolts, rose, and lever.

Fig.

Fig.

.. Align the holes in the liner with

the holes prepared in the door.

.. Install through-bolts through the

liner and the door in the top and

bottom holes.

.. Tighten the liner onto the door

with the through-bolts.

.. Slide the rose over the sleeve,

then press the rose onto the liner.

The rose should fit closely to the

door surface.

.. With the lever pointing toward

the hinges, push the lever on

firmly until seated.

. Install strike plate.

. Adjust lockset to door thickness.

. Engage retractor in latch.

Fig.

Fig.

Follow these steps to adjust thickness:

.. Temporarily remove the latch.

.. Retract the rose locking pin and rotate

the outside rose liner in or out for the

proper door thickness by lining up the

“DOOR CENTER” mark with the center

of the latch hole.

.. Reinstall the latch.

.. With the latch in place, install the chassis from

the outside. Make sure the latch tabs engage

the chassis frame and the latch tailpiece

engages the retractor.

Door center

Retractor

Pull pin to

rotate rose

Chassis frame

Latch stab

Latch i ceta lpie

Retr torac

Chassis

Liner

Through-

bolts

Rose

Sleeve

Lever

In eside ros

Lever

Inside

liner

Latch

Th h-boltsroug

Outside

Outside rose

TEMPLATE

High edge of

door bevel

.. In alignment with the center of the

latchbolt, mortise the door jamb to fit

the strike box and strike plate.

.. Insert the strike box and secure the

strike with the screws provided.

Door jamb

St ke boxri

Strike plate

CAUTION: The deadlocking plunger of

the latchbolt must not enter the strike

plate opening. The plunger deadlocks

the latchbolt and prevents forcing the

latch when the door is closed. A gap of

more than 1/8" (3 mm) may reduce

security and/or cause improper

operation of the latchbolt.

Installation Instructions: C cylindrical lock

 Technical specifications

. Caution

Caution: If you use hollow metal doors, determine whether the doors

are reinforced enough to support the lock. If door reinforcement is not

adequate, consult the door manufacturer for information on proper

reinforcement. Maximum door opening degree is °.

Caution: The deadlocking plunger of the latchbolt must not enter the

strike plate opening. The plunger deadlocks the latchbolt and prevents

forcing the latch when the door is closed. A gap of more than / ” (

mm) may reduce security and/or cause improper operation of the

latchbolt.

. Tools recommended

Table 

# and # Phillips screwdriver -/" ( mm) hole saw

Tape measure " (25 mm) hole saw or drill bit

Hammer Drill

" ( mm) wood chisel Drill bit: /" ( mm) drill bit

Caution: Since the control key is a high-security key, make sure to keep

it protected.

DORMA-C200 series 10-2021T91907_A

Installation Instructions: C200 Cylindrical

www.dormakaba.us

. Remove the lever.

3.2 Install the lever insert and lever handle.

Fig.a—Fig.b

3.4 Assemble and install optional I/C core.

Fig.

Fig.a—Fig.b

 Instructions - C key-in-lever cylinders

. Assemble and install key-in-lever cylinder.

Fig.b

Fig.b

These instructions describe how to install a key-in-lever cylinder into a C

dormakaba lever handle. Use these instructions only after completing the

installation of the cylindrical chassis.

.. From the bag of keys, cylinders

and throw members, keep only

the shortest throw member.

Discard the other throw

members—they will not be

needed.

.. Remove the outside lever if it’s

not already off.

.. Assemble the key-in-lever

cylinder as shown in Figure a.

.. Install the lever insert as shown in

Figure a. Make sure that the lever

insert is completely seated.

.. Install the key-in-lever cylinder

assembly into the handle. See

Figure b.

Fig.a

Fig.a

NOTE: Make sure that the throw

member blade is installed aligned with

the cylinder ‘bible’ as shown in Figure

a. This prevents unauthorized removal

of the cylinder.

NOTE: Do not disassemble the

cylinder with the key inserted. Doing so

may cause the pins to fall out.

Follow these steps to install the

key-in-knob cylinder into a C

lever handle.

Key-in-lever

cylinder

assembly

58"

Throw

member

Bible

End cap

For Classroom Function () locks only:

For all other keyed function locks:

Lever insert

Lever orientation

Lever keeper

Orientation of

cam

Sleeve

Clearance area

Looking head-on into the outside sleeve,

with the latch to be on the right.

.. Turn the cam counterclockwise until it stops.

Then rotate clockwise  (or until it aligns °

with the clearance area on the lever keeper).

See Figure b.

.. Insert the key into the cylinder and turn

the key  clockwise.°

.. Push the lever on until it is completely seated.

.. Remove the key for the cylinder.

.. Insert the key into the cylinder.

.. Push on the lever handle until it stops.

For all function locks:

.. Insert the throw member into the core.

.. Put the control key into the core and

turn the key  clockwise.°

.. Put the core and throw member into the

lever with the control key.

.. Turn the key  counterclockwise and °

remove the key.

.. Insert the key into the cylinder and

turn the key  clockwise.°

.. Depress the keeper with a tool.

.. Remove the lever.

Throw

member

Control key

in core

Core

NOTE: For Classroom Function () locks only:

Insert a screwdriver into the figure-

opening and turn the locking mechanism

counterclockwise as far as it will go.

.. Turn the key ° clockwise while

applying pressure and push the lever

on until it is completely seated.

.. Remove the key from the cylinder.

For nline nstructions isit:o i v

https://dhwsupport.dormakaba.com/hc/en-us

For ssistance or a w arranty information:

Call 1-800-392-5209 or isitv

https://dhwsupport.dormakaba.com/hc/en-us

Especificaciones del producto

Marca:	Dormakaba
Categoría:	No categorizado
Modelo:	C200

¿Necesitas ayuda?

Si necesitas ayuda con Dormakaba C200 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado Dormakaba Manuales

Dormakaba X-ZONE T Manual de Usario

2 Septiembre 2024

Dormakaba Keyscan LUNA Manual de Usario

2 Septiembre 2024

Dormakaba RCI 4 Manual de Usario

2 Septiembre 2024

Dormakaba 9000 Manual de Usario

2 Septiembre 2024

Dormakaba Crane 2000-M Manual de Usario

2 Septiembre 2024

Dormakaba Auditcon 52 Manual de Usario

2 Septiembre 2024

Dormakaba E-Plex 3x00 Manual de Usario

2 Septiembre 2024

Dormakaba HSD-L07 Manual de Usario

2 Septiembre 2024

Dormakaba Cencon 4.1.5 Manual de Usario

1 Septiembre 2024

Dormakaba MUTO Recessed Manual de Usario

1 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024