Dormakaba RCI 0162 Manual de Usario

Dormakaba No categorizado RCI 0162

Lee a continuación 📖 el manual en español para Dormakaba RCI 0162 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Fail Secure = Fail Locked = FL AC = Alternating Current DC = Direct Current

Intermittent Duty = Energized less than 1 minute with 1:5 duty ratio Continuous Duty = Energized 1 minute or more

I N S T A L L A T I O N F0162 / 0162

F0162LM / 0162LM

IS0162 PCN18003

R02-18TG-1

Important: The F0162 or the 0162 Electric Strikes should never be used as a door stop. Please install stops on frame in

appropriate locations. Ensure the exit device functions as intended for life safety concerns by verifying electric strike and

exit device compatibility. Maximum latch projection is essential to obtain full holding force.

When installed in a fail secure manner, the local Authority Having Jurisdiction shall be consulted with regard to the use

of selected panic hardware to ensure emergency exit from the secured area.

Installations of this RIM strike qualify as “Indoor Use Only” when not continuously exposed to an outdoor environment.

Catalog Specifications

MODE VOLTAGE CURRENT DUTY AMPS OHMS

Fail Secure 12V AC Intermittent 0.33 22

Fail Secure 12V DC Continuous 0.50 22

Fail Secure 24V AC Intermittent 0.64 22

Fail Secure 24V DC Continuous 0.24 89

Fail Secure 11-16V AC Intermittent 0.32-0.50 22

1-3/4”

(44.5mm)

3/4”

(19.0mm)

9”

(228.6mm)

5-1/2”

(139.7mm)

1-5/8”

(42.0mm)

8-1/4”

(209.6mm)

HORIZONTAL

ADJUSTMENT

MOUNTING

HOLES

MODEL WITH

LATCH MONIT

LOCK DOWN

HOLES

SURFACE MOUNTED RIM STRIKE

(FIRE RATED AND NON-FIRE RATED)

Electrical Latch Monitor

Speciﬁcation:

• 12VDC, 1A, resistive load

Note: Contacts identiﬁed on the

harness sleeve are indicated with the

keeper in a closed and locked condition,

with no latch present

Dimensional Details

UL 294 Performance Ratings:

Access Control Line Security : Level I

Destructive Attack : Level I

Endurance : Level IV

Standby Power : Level I

www.rutherfordcontrols.com hone ax • P : 1.800.265.6630 • F : 1.800.482.9795 • Email: sales_RCI@dormakaba.com

LOCKING SCREW

(2 PLACES)

3/4" (19.0 mm)

WIRE ACCE

SS HOLE

1/4-20 UNC

(2 PLACES)

DOOR FRAME

DOOR FRAME STOP

MOUNTING SCREW

(2 PLACES)

MOUNTING SCREW

(2 PLACES)

1/4-20 UNC

(2 PLACES)

3/4" (19.0 mm)

WIRE ACCE HOLESS

DOOR FRAME STOP

5/8" (16.0mm)*

WIRE ACCE

SS HOLE

LM MODEL ONLY 5/8" (16.0mm)*

LM MODEL ONLY

NOTE: NOTE: * Wire access hole locations are relative to the exit device orientation. Second wire access hole required for 0162LM only

NOTE: Not to scale. Specifications are subject to change without notice.

Instructions

1. Determine the horizontal centerline of the exit device latch and transfer centerline to the frame stop.

2. Position the template onto the frame aligning with centerline and against the closed door. Center-punch the two

mounting holes and the wire access hole as shown.

3. Drill and tap the two mounting holes and drill the wire access hole(s).

4. Test fit electric strike to ensure full latch engagement. Add provided spacer if required.

5. Make wire connections from the power source to the appropriate wire harness supplied. Use 12VDC wire harness for

12VDC, 12-24VAC or 11-16VAC input power. Use 24VDC wire harness for 24VDC input power only.

NOTE: Overheated or burnt coils caused by incorrect input voltage / wire harness combinations will not be

covered under warranty

6. Connect monitor wires of LM model.

7. Mount the electric strike with 1/4-20 UNC screws provided in the horizontal mounting holes (the outer slots).

Adjust electric strike horizontally until exit device latch fully engages with the door closed.

NOTE: Ensure a 1/16” [1.5mm] clearance between

exit device latch and the electric strike keeper is

maintained. Failing to do so will preload the strike

and in turn will not allow the strike to release the

door upon energizing.

WARNING: For proper operation, a 3/16” gap

(minimum) is required.

8. Tighten the two mounting screws and check operation.

Adjust the horizontal position of electric strike as required.

9. Use the electric strike as a template to mark the two locking holes. Remove strike. Drill & tap for 1/4-20 UNC locking

screws. Using the 1/4-20 UNC screws provided secure the electric strike through the locking holes.

RIM ELECTRIC STRIKE

EXIT DEVICE LATCH

DOOR FRAME

STRIKE KEEPER

3/16”

MINIMUM

1/16” minimum

www.rutherfordcontrols.com hone ax • P : 1.800.265.6630 • F : 1.800.482.9795 • Email: sales_RCI@dormakaba.com

Especificaciones del producto

Marca:	Dormakaba
Categoría:	No categorizado
Modelo:	RCI 0162
Tipo de operación:	Touch
Color del producto:	Roestvrijstaal
Pantalla incorporada:	Ja
Ancho:	600 mm
Profundidad:	500 mm
Altura:	663 mm
Nivel de ruido:	66 dB
Clase-de-eficiencia-energética:	C
Consumo-anual-de-energía:	78 kWu
Amable:	Muurmontage
Potencia del motor:	- W
Número de motores:	1
Capacidad máxima de extracción:	608 m³/uur
Método de extracción:	Luchtafvoer
Clase de eficiencia fluidodinámica:	D
Clase de eficiencia lumínica:	A
Clase de eficiencia del filtro de grasa:	D
Nivel de ruido (baja velocidad):	50 dB
Número de lámparas:	2 gloeilamp(en)
Tipo de lámpara:	LED
Tipo filtro veterinario:	Metaal
Lámpara de encendido:	2.5 W
Nivel de ruido (alta velocidad:	59 dB
Número de filtros:	2 stuk(s)
Número de velocidades:	3
Nivel de ruido (velocidad media):	52 dB
Filtro apto para lavavajillas:	Ja
Druk (Pa):	244
Tipo-de-visualización:	LED