Dormakaba RCI 8365 Manual de Usario

Dormakaba No categorizado RCI 8365

Lee a continuación 📖 el manual en español para Dormakaba RCI 8365 (3 páginas) en la categoría No categorizado. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

INSTALLATION

RCI 8365

MicroMag MORTISE ELECTROMAGNETIC LOCK®

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

1. Mortise Cutouts

Hold lock against frame at desired level. Mark the lock’s horizontal

centerline on the frame and transfer that mark to the door.

Determine the vertical centerline of the door thickness and mark

this on both the door and the frame.

Using these centerline references, cut out the frame lock mortise

and the door armature mortise, as illustrated.

2. Lock Mounting Tabs

Temporarily fasten the two mounting tabs under the lock flanges.

Insert the lock assembly into the frame cavity until the tabs are

resting on top. Mark the location of the tab mounting holes.

Drill and countersink these four holes to accept the 3/16” screws

provided.

Remove tabs from lock. Mount the tabs inside the frame.

3. Wire and Mount Lock

Remove endcap.

Set voltage jumpers as follows:

12VDC operation = two jumpers are used.

Contact pins 1 to 2 and 3 to 4.

24VDC operation = only one jumper is used.

Contact pins 2 to 3. (factory setting)

Connect the positive (+) power lead to the red and the negative

(-) lead to the white wire.

Connecting wire should be

of sufficient gauge for the

lock being installed and the

distance being run.

See page 3 table for current

draw specifications.

Secure lock on tabs in

mortise cavity, carefully applying thread locking compound to the

hardware provided, as in Fig. 1

IS8365 PCN18041

R09-19GR-1

Instructions

Pre-Installation Instructions

1. This product must be installed according to all applicable

building and life safety codes.

2. Due to the variety of mounting configurations available with this

product, a survey and assessment of the physical area in which

the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally

sound prior to installation of the electromagnetic lock. The

structural integrity of the mounting surfaces must be strong

enough to meet or exceed the holding force of the product.

4. The product must be protected from potential damage due to

intruders or tampering.

5. The product should be installed in a location that will not hinder

or create a potential safety hazard to authorized personnel

accessing the protected area.

6. Because electromagnetic locks are used in a variety of

applications and different door frame configurations, an

experienced installer with knowledge of this product must make

a determination of the optimal mounting method for this specific

application.

7. Do not install this product on the exterior of buildings.

8. Do not use as a doorstop. This will void warranty.

9. Installation of this product should be done by an experienced

installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound be

applied to all screws during installation to reduce chance of screws

loosening over extended time.

WARNING: Improper installation, maintenance, inspection or

usage of the product or any related accessories or parts may

cause the electromagnetic lock, armature plate and associated

hardware to disengage and fall, causing serious bodily injury and

property damage. dormakaba Canada Inc. and/or dormakaba

USA Inc. will not be liable to the installer, purchaser, end user

or anyone else for damage or injury to person or property due

to improper installation, care, storage, handling, maintenance,

inspection, abuse, misuse or act of God or nature involving this

product or any related accessories or parts.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

4. Mount Armature

Using centerline references on the door and illustration provided,

drill the four “U” clamp mounting holes.

Position the “U” clamp inside door as shown on Fig. 2. Insert the

two pan head sex nuts from the outside of the door and through the

“U” clamp. Insert the two button head hex bolts from the inside of

the door and secure into the sex nuts.

Position bolt with rubber head through armature plate. Add 3

washers (steel - rubber - steel) onto threads. Carefully apply thread-

locking compound to exposed thread and mount onto the “U”

clamp.

NOTE: Do not over tighten. The armature plate must be allowed to

pivot on the mounting bolt to allow proper alignment with the magnet

surface. If the plate is not aligned with the magnet surface, the lock

may lose holding force or not lock at all.

The head of the armature mounting bolt ships with a rubber washer

affixed to it. This washer should project slightly beyond the surface

of the armature plate. This is to allow the washer to expand when

power is removed and break the air vacuum between the plate

and the magnet surface. If this washer is removed or trimmed, the

lock will appear to have some holding force even when power is

removed.

5. Validate

With a release device already installed, energize circuit and close

door gently. If magnet does not secure, verify that armature plate

is making contact with face of magnetic block. If necessary, install

additional steel washers behind armature plate to move armature

plate closer to block face and retest.

Inspection and Maintenance

This product and all related accessories or parts must be inspected

and maintained on a Contacting surfaces of quarterly basis.

the electromagnetic lock and armature plate must be kept free of

contaminating materials. Surfaces must be cleaned periodically with a

non-abrasive cleaner.

All mounting fasteners must be inspected on a When quarterly basis.

properly installed, the ends of the armature plate allow a slight movement

but the plate will feel secure when grasped at the bolt. There should be

no movement to the mounting bracket or housing of the electromagnetic

lock.

For added safety, thread locking compound has been provided for the

armature plate bolt and the four electromagnetic lock mounting screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware

to disengage and fall, causing serious bodily injury and property

damage.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO THE

END-USER UPON COMPLETION OF THE INSTALLATION.

NOTE: All RCI brand electromagnetic locks must be powered with filtered and regulated DC power supplies. dormakaba offers a full line of power

supplies and switching devices that are suitable for use with the 8300 Series locks.

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

8365

Electromagnetic

Lock

Mounting

Tab

Frame

Extrusion

Frame

Sliding Door

Exterior

Exterior side

door drilling

Interior side

door drilling

Side

Interior

Side

Shock absorbing

rubber washer

Metal

washers

cut

out

cut

out

J *

I *

"U" Clamp

Do not over tighten

preventing movement.

Frame

Sliding Door

Inches

Fractions

Inches

Decimal

(mm)

metric

1-3/8

1.38 8.00 1.31 5.19 1.05 0.55 0.34 0.50

35.0 203.0 33.0 132.0 27.0 14.0 8.5 13.0

8 1-5/16 5-3/16 1-1/16

AB E F G H I (Interior)* J (Exterior)*

FRAME DOOR

9/16 11/32 1/2

Voltage Current

12VDC 0.40A

24VDC 0.20A

* Interior and exterior drill sizes are different

NOTE: Specifications are subject to change without notice.

Fig.1

Fig.2

Especificaciones del producto

Marca:	Dormakaba
Categoría:	No categorizado
Modelo:	RCI 8365

¿Necesitas ayuda?

Si necesitas ayuda con Dormakaba RCI 8365 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado Dormakaba Manuales

Dormakaba X-ZONE T Manual de Usario

2 Septiembre 2024

Dormakaba Keyscan LUNA Manual de Usario

2 Septiembre 2024

Dormakaba RCI 4 Manual de Usario

2 Septiembre 2024

Dormakaba 9000 Manual de Usario

2 Septiembre 2024

Dormakaba Crane 2000-M Manual de Usario

2 Septiembre 2024

Dormakaba Auditcon 52 Manual de Usario

2 Septiembre 2024

Dormakaba E-Plex 3x00 Manual de Usario

2 Septiembre 2024

Dormakaba HSD-L07 Manual de Usario

2 Septiembre 2024

Dormakaba Cencon 4.1.5 Manual de Usario

1 Septiembre 2024

Dormakaba MUTO Recessed Manual de Usario

1 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024