Edifier C2V Manual de Usario

Lee a continuación 📖 el manual en español para Edifier C2V (1 páginas) en la categoría Vocero. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/1
English
www.edifier.com
EDIFIER INTERNATIONAL LIMITED
Made in China
NOTICE:
For the need of technical improvement and system upgrade,
information contained herein may be subject to change
from time to time without prior notice
Copyright 2007
All Rights Reserved.
Manual Edition 1.1 , Dec. 2007
Printed in China
1 2
EnglishEnglish
3 4
EnglishEnglish
5 6
EnglishEnglish
7 8
EnglishEnglish
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTION Unpack the box
Box content
Amplifier
Subwoofer
2 satellite speakers
Remote control (RC30)
3.5mm to dual RCA connector cable
User's manual
Amplifier
Subwoofer
Remote control (RC30)User's manual
3.5mm to dual RCA connector cable
Satellite speaker
Satellite speaker
Illustrations and Functional Depict
1. Power on/stand-by button
2. Audio signal input status indicator
3. Audio signal input socket
4. Display window and IR receiver
5. Mode adjustment indicator
6. Audio signal output socket
7. “VOLUME” volume adjustment knob
8. Working indicator (halo)
9. “FUNCTION” function buttons
10. “INPUT” Input selection button
11. Headphone jack
12. Power switch
Front view of amplifier Rear view of amplifier
Making connections
Left satellite speaker
To A.C
Subwoofer
Right satellite speaker
Operational guidance Guidance for using remote control
Operational guidance
1. Connect the speakers and audio source
Please refer to illustrations in "Making connections"
2. Power on/off the system
Plug the power cord and turn on the power switch, the digital display will show "- -", indicating that system is in STBY mode.
Press the " " button on amplifier or " " key on remote control, the power indicator and PC input indicator will be lit; digits
shown in the digital display will run from "0" to "30", the default level of master volume. System now enters working mode.
Rotate the " " knob to adjust master volume, from 0 to 60. "0" means minimum, "60" for maximum.
Press the " " key on amplifier or " " key on remote control when system in working mode will set it back to STBY.
3. Input selection
The system has "PC" and "CD/AUX" inputs, and "PC" is the default input. Press the "INPUT" selector on front deck of
amplifier to switch between "PC" and "CD/AUX" inputs, the digital display will show the name of current input ("PC" or "CD").
4. Trimmers / control
Press the "Function" key when system in working mode, the "Bass" and "Treb" trimmer indicators will be lit sequentially:
when "Bass" lit, bass trimmer on; when "Treb" lit, treble trimmer on; when both off, back to master volume control.
The digital display will show corresponding trimmer / control value: when "Bass" lit, figure shown is bass trimmer value;
when "Treb" lit, it is treble trimmer value; when both off, it is master volume level.
Rotate " " knob to adjust the trimmers / control: when "Bass" lit, rotate the " " knob to adjust the bass
trimmer from -9 to +9; when "Treb" lit, rotate to adjust the treble trimmer from -7 to +7; when both off, rotate to adjust
the master volume.
3 seconds no action in trimmer mode, system will go back to master volume adjustment, with both trimmer indicators off
and digital display shows current master volume level.
5. Headphone output
Plug the headphone plug into the " " on amplifier's front deck. It works correctly if the output from speaker is shut and
power indicator off. " " knob can control the headphone output and digital display shows the current master
volume level.
Point the remote control to the IR window on front deck of amplifier when operating the remote control.
The optimum operational distance is 7 meters. When a remote command is received and executed,
figures shown in digital display will blink.
1. " " -- STBY/ON key
Press this button will set the system on / STBY.
2. "MUTE"
Press this button when system in working mode will instantly shut off the
speaker output. The power indicator is still on and digital display blinks
current master volume level.
Press one more time this button will recall the speaker output.
3. "Volume +/-" keys
Adjust the master volume level from 0 to 60.
4. "SW +/-" keys
Bass trimmer adjustment. When press the keys, the "Bass" trimmer
indicator will be lit and digital display shows the value.
5. "TRE +/-" keys
Treble trimmer adjustment. When press the keys, the "Treb" trimmer
indicator will be lit and digital display shows the value.
6. "PC / AUX" keys
Input selectors. Press the "PC" key, system gets signal from "PC" input,
and "PC" input indicator lit; press the "AUX" key, system gets signal from
"CD/AUX" input, and "AUX" input indicator lit.
Note: "SW +/-" and "TRE +/-" are trimmer adjustments which are both tone controls based on master volume level.
"SW +/-" ranges from -9 to +9; "TRE +/-" ranges from -7 to +7; minus figure refers to attenuation, positive for boost,
and "0" for no boost and no attenuation. 3 seconds no action in trimmer mode, the system will return to master
volume adjustment.
Battery loading:
Please refer to the figure on the right side to open the battery compartment,
load the included C2025 battery and shut the compartment.
The battery (battery or batteries or battery pack) shall not be exposed to
excessive heat such as sunshine, fire or the like.
Note:
• Do not place the remote in places that are hot and moist;
• Unload the battery when unused for long period of time.
Specification
Amplifier power output: Satellite channel: RMS 6W X 2 (THD+N=10%)
Subwoofer channel: RMS 18W (THD+N=10%)
Signal-to-Noise Ratio(Amplifier): ≥85dBA
Distortion: ≤0.5%
Input impedance: 10K ohm
Input Sensitivity: R/L: 300mV±50mV
SW: 150mV±50mV
Volume control: Front panel controls for volume and Bass level adjustments,
remote control
Bass Unit: 6.5 inch (166mm), Magnetically Shielded, 4 Ohm.
Midrange Unit: 3 inch (78mm) , Magnetically Shielded, 4 Ohm.
Tweeter Unit: 3/4 inch PV membrane dome, Magnetically Shielded, 8 Ohm.
Power input: 100V-120V ~, 50/60Hz (for USA/Canada/Japan models)
220V-240V ~, 50/60Hz (for European/China/Korea/South
America, etc.models)
Dimension: Amplifier: 72(W)x223(H)x213(D) mm
Subwoofer: 246(W)x252(H)x271(D) mm
Satellite: 90(W)x181(H)x137(D)mm
Weight: Approx. 9.2kg
Warnings:
Please do not feed powered signal from another amplifier into the input ports of this system!
Please adjust to a comfortable volume to avoid damaging your hearing and the system!
Dangerous voltage inside the subwoofer enclosure, please do not open the chassis.
Refer to qualified personnel for servicing.
Please remove the power plug if the system is unused for long period of time.
Please do not expose the system in rain or moisture environment.
Please do not place vase or utensil full of liquid on the speaker.
Troubleshooting
Not all speakers function:
Please first check if the speaker wires are connected securely;
then check if the Line-in connectors are reversed; check also if the audio source is at fault.
One satellite speaker does not function when playing CD from computer:
This kind of phenomena is prone to happen on new computer systems that one satellite
does not function when playing CD, but system works fine when playing WAV formatted files.
This is mainly due to the fault connection of CD-ROM and sound card, that one channel of
signal is shorted to the ground.
Please refer to the manual of CD-ROM and sound card to adjust the wire connection.
System does not work at all
1. Please check if power is connected, and if the wall outlet is switched on.
2. Please check if the amplifier is still in STBY mode
3. Please check if the master volume is turned to minimum
4. Please check if the audio input cable is connected correctly
5. Please check if there is signal from audio source
Noise coming from speakers
Amplifier circuitry of this product generates little noise, while the background noise of
some VCD/DVD player or computer sound card are too high.
Please keep the system in active mode and remove the audio source, if no sound can
be heard at 1 meter away from the system, then there is no problem with this product.
Magnetic interference
This system is complete magnetically shielded, and can be placed near TV or monitor.
But since magnet of the subwoofer driver is large, some magnetism leakage is inevitable
when the system is too close to the monitor, and it is recommended to keep a 1 meter
distance between the speaker system and monitor or TV set.
If you have any further questions or concerns regarding Edifier Products
Please visit our website at: www.edifier.com, or email Edifier Support for further
assistance at: main@edifier.com, If you prefer, you may contact us by phone,
Toll Free: 1-877-EDIFIER (334-3437).
1. Connecting the speakers
Please connect the left and right satellite speakers to the back panel of the external amplifer as indicated in
the diagram.
2. Connecting the system to the audio source
Please connect the sound card of your PC or other audio sources to the PC IN input connector with
the 3.5mm to dual RCA audio connecting cable, Connect Aux sources to aux input socket.
3. Connect to the power
Connect the power plug to an AC outlet, and please match the correct voltage for your area.

Especificaciones del producto

Marca: Edifier
Categoría: Vocero
Modelo: C2V

¿Necesitas ayuda?

Si necesitas ayuda con Edifier C2V haz una pregunta a continuación y otros usuarios te responderán




Vocero Edifier Manuales

Vocero Manuales

Últimos Vocero Manuales