Elba ETM-E3690P Manual de Usario
Lee a continuación 📖 el manual en español para Elba ETM-E3690P (1 páginas) en la categoría Kraan. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/1
ETM-E3690P
1. An opening hole of 35mm diameter is required on sink top or work top (C) for installation of tap.
2. Slide the rubber O-ring (B) up to the base of tap (A).
3.Screw the flex hoses (H) up to the extension tube, then insert the tap through the hole of sink top or
worktop (C), and position the tap properly.
4.Slide the plastic fitting I (D) through the extension tube ,then slide the plastic fitting II (E) through the
sprayer hose and up to the plastic fitting I(D).
Important: ensure the opening of plastic fitting I (D) is close to threaded tube , and the sprayer hose
runs freely through the plastic fitting II (E).
5.Put the permanent seat(F) through the threaded tube , and tighten the fixing washer(G) securely.
Important: make sure the hose runs smoothly before tightened the fixing washer.
6.Connect the flex hoses (H) to the hot & cold water supply, and the sprayer hose to the threaded tube.
7. Adjusting the pull-out length of sprayer hose and fasten the weighing ball (I) with screws.
●Before installation, please ensure that the following
work conditions are adhered to:
-Water temperature between 0 C - 90 C˚ ˚
-Water pressure between 0.05MPa – 1.0MPa. Pressure
reducing valve is necessary if pressure exceeds 1.2MPa
-Avoid major pressure di erences between hot and cold ff
water supply
●Flush pipes thoroughly before and after installation to
ensure water supply is free of any debris.
●Inspect tap fitting and debugged to its best. Do not
attempt to disassemble fitting on your own.
●Use thread sealant tape (PTFE) on any screw joining
connections and ensure all joints are securely tightened.
A Tap body
B Rubber O ring
C Sink top or work
top
D Plastic fitting I
E Plastic fitting Ⅱ
F Permanent seat
G Fix ing washer
H Flex hose
I Weighing ball
J Rubber washer
for flexi hose
This . FIAMMA SDN. BHD. will not be held responsible for the use of superseded or voided specifications.
Fabricatoe must check for cut-out accuracy.
specification is subject to change without notice
Stainless Steel Mixer Tap
Especificaciones del producto
Marca: | Elba |
Categoría: | Kraan |
Modelo: | ETM-E3690P |
¿Necesitas ayuda?
Si necesitas ayuda con Elba ETM-E3690P haz una pregunta a continuación y otros usuarios te responderán
Kraan Elba Manuales
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
Kraan Manuales
- Kraan IKEA
- Kraan Etna
- Kraan Inventum
- Kraan Smeg
- Kraan KitchenAid
- Kraan Teka
- Kraan Miomare
- Kraan Ernesto
- Kraan CDA
- Kraan Stiebel Eltron
- Kraan Grohe
- Kraan Franke
- Kraan Nodor
- Kraan Delta
- Kraan Elkay
- Kraan Caple
- Kraan Quooker
- Kraan Brita
- Kraan ZLine
- Kraan Hansgrohe
- Kraan Empire
- Kraan Moen
- Kraan Aloni
- Kraan WillieJan
- Kraan Sani-Lav
- Kraan Mizzo
- Kraan Brauer
- Kraan Fala
- Kraan Lomazoo
- Kraan Deante
- Kraan Omnires
- Kraan Viidako
- Kraan Curaqua
- Kraan Waltec
- Kraan Sussex
- Kraan Oliveri
- Kraan Axor
- Kraan Graff
- Kraan Zurn
Últimos Kraan Manuales
27 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
25 Septiembre 2024
22 Septiembre 2024
21 Septiembre 2024