Electro Harmonix Hell Melter Manual de Usario

Electro Harmonix No categorizado Hell Melter

Lee a continuación 📖 el manual en español para Electro Harmonix Hell Melter (4 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Congratulations, you are now possessed by the Hell Melter. This device

is built to produce the legendary ‘chainsaw’ distortion tone, but with

added features that expand the threat of tonal destruction. Do you

want the gruesome vintage grind found on classic death metal records?

Do you seek added volume, distortion, clarity, or control? Sink deep

into the Hell Melter and you shall nd all the havoc you’ll ever need.

Operating Instructions

Connect your guitar to the INPUT jack of the Hell Melter and the OUTPUT

jack to your amp’s input. Plug in the included power supply and plug its

output plug into the Hell Melter’s power jack. Press the EFFECT footswitch

to ensure the red LED is lit, and the Hell Melter is ready.

A good starting point is to turn all the knobs (except for DRY LVL and GATE)

to their maximum positions and play the heaviest riffs you've got. Setting

all the EQ knobs to maximum, including MID FREQ, produces the uniquely

punchy “chainsaw” sound that has powered countless heavy bands.

Note: the original circuit that produced this sound used components

with wide tolerances, resulting in noticeable tone differences from unit

to unit. The Hell Melter can recreate many of these different tones with

slight tweaks near the maximum position of the MID FREQ knob.

POWER SUPPY REQUIREMENTS:

Voltage: Current: 9VDC 140mA Center-Negative Polarity:

This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. Use of the wrong adapt-

er or a plug with the wrong polarity may damage the device and void the warranty. Do not exceed 12VDC

on the power plug. Power supplies rated for less than 140mA can cause the device to act unreliably

Advanced Heavy Metal Distortion

- 2 -

1. DISTORTION Knob Adjusts the amount of distortion and saturation, from a

light grind to a roaring chainsaw. Turn clockwise for more distortion.

2. LEVEL Knob Adjusts the overall output level of the Hell Melter. Turn clockwise

for more output. More output is available than on the original ‘chainsaw’ circuit.

3. LOW Knob Provides active boost or cut to the bass frequency range. The middle

position leaves bass frequencies at.

4. MID LVL Knob Provides active boost or cut to the mid frequency, with the

frequency set by the MID FREQ knob. The middle position leaves mid frequen-

cies at.

5. MID FREQ Knob Adjusts the frequency boosted or cut by the MID LVL knob.

Turn the knob clockwise to increase the frequency.

Controls and Connections

- 3 -

6. HIGH Knob Provides active boost or cut to high frequencies. The middle posi-

tion leaves high frequencies at. Tip: the frequencies controlled by the HIGH

Knob are slightly lower than a typical ‘treble’ control, allowing you to produce

searing highs without a lot of treble harshness. To emphasize even higher

‘treble’ frequencies, turn the HIGH knob below the middle position, and increase

the LEVEL knob to re-emphasize treble.

7. NORM/BURN Switch Switches between “Normal” and “Burn” Modes:

Normal Mode The famous vintage chainsaw distortion sound.

Burn Mode A custom, modernized distortion sound, utilizing higher voltage

rails and alternative clipping options. This results in a less compressed and

more open distortion sound with a more pronounced attack.

8. GATE Mini Knob Removes unwanted hum by adjusting the noise oor thresh-

old. The gate mutes the OUTPUT jack when the signal at the INPUT jack is below

the threshold setting of the GATE knob. As GATE is turned clockwise, a louder

guitar signal at the INPUT jack is required to unmute the OUTPUT jack. Set GATE

fully counter-clockwise to disable.

Setting the GATE knob: Start with GATE fully counterclockwise, DIST above noon,

and your guitar volume at max. You may want to hold the strings so they don’t

ring out. Slowly turn GATE clockwise until the Hell Melter mutes. Now turn GATE

a little further clockwise and then test it. If you have to play with too much force

to unmute the gate, then turn GATE a little counter-clockwise. If you want the

gate to act more quickly at the end of notes, then turn GATE further clockwise.

9. DRY LVL Mini Knob Adds clean, undistorted input signal to the output. As the

knob is turned clockwise, the amount of dry signal increases. At the minimum

position, no dry signal is mixed into the output. Tip: this is especially useful to

maintain note clarity when stacking the Hell Melter with a dirty amp or another

gain pedal.

10. EFFECT Footswitch and Red LED This footswitch engages or bypasses the

effect. The LED lights when the effect is active. The Hell Melter employs high

quality buffered bypass.

11. BOOST Footswitch and Yellow LED This footswitch engages Boost Mode, add-

ing extra gain at the input of the circuit, and adjustable volume boost.

12. BOOST LEVEL Internal Trimmer This trimmer controls the additional volume

added when Boost Mode is active. To access it, remove the 4 screws on the back

plate of the Hell Melter, and locate the trimmer next to the BOOST Footswitch.

Taking care not to touch the rest of the circuitry of the board, turn this trimmer

clockwise using a small at-head screwdriver to increase the volume boost. At

the minimum position, Boost Mode provides no volume boost.

13. INPUT Jack Audio input to the Hell Melter.

14. OUTPUT Jack Audio output from the Hell Melter.

15. 9V Power Jack Attach the output plug from the included power supply to the

9V power jack. The Hell Melter draws 140mA at 9VDC on a center-negative plug.

Do not exceed 12VDC on the power jack. The Hell Melter does not take batteries.

Especificaciones del producto

Marca:	Electro Harmonix
Categoría:	No categorizado
Modelo:	Hell Melter
Colocación del dispositivo:	Vrijstaand
Tipo de operación:	Draaiknop
Color del producto:	Wit
Bisagras de puerta:	Links
Pantalla incorporada:	Ja
Peso.:	65000 g
Ancho:	600 mm
Profundidad:	540 mm
Altura:	850 mm
Tipo de enchufe:	Type F
tipo de cargador:	Voorbelading
Color de la puerta:	Wit
Material del tambor:	Roestvrijstaal
Contenido del tambor:	58 l
Temporizador de inicio retrasado:	Ja
Retraso del inicio:	24 uur
Indicación de tiempo restante:	Ja
Bloqueo infantil:	Ja
control wifi:	Ja
Clase-de-eficiencia-energética:	B
Peso del embalaje:	67000 g
Ancho del embalaje:	650 mm
Empaquetadura en profundidad:	560 mm
Altura del embalaje:	890 mm
Consumo de energía de lavado:	0.57 kWu
Consumo de agua por ciclo:	46 l
Clase de medicamentos centrífugos.:	B
Nivel de ruido (lavado):	- dB
Velocidad centrífuga ajustable:	Ja
Velocidad máxima de centrifugado:	1400 RPM
Bluetooth:	Ja
Clase de emisión de ruido:	C
Nivel de ruido durante la centrifugación.:	79 dB
Tiempo de ciclo (máx.):	228 min
Número de programas de lavado:	16
Duración del ciclo (programa de lavado rápido):	14 min
Consumo de energía por 100 ciclos.:	57 kWu
Temperatura-ajustable:	Ja
Kijkglas:	Ja
Aplicaciones de control compatibles:	hOn
Puerta-abierta:	Opening aan zijkant
Capacidad nominal:	9 kg
voltaje-de-entrada-de-CA:	220 - 240 V
Escala de eficiencia energética:	A tot G
Programas-de-lavado:	Cotton, Cottons 20°C, Eco, Hand/wool, Hygiene/anti-allergy, Quick, Quick 14min, Quick 30min, Spin/drain, Sport, Steam, Synthetics
Color-de-la-manija-de-la-puerta:	Wit
Programa de lavado todo en uno (Todo en uno):	Alles in één