Electro Harmonix Next Step Slammi Manual de Usario

Electro Harmonix No categorizado Next Step Slammi

Lee a continuación 📖 el manual en español para Electro Harmonix Next Step Slammi (4 páginas) en la categoría No categorizado. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

SLAMMI

POLYPHONIC PITCH-SHIFT /HARMONY PEDAL ER

Congratulations on your purchase of the Electro-Harmonix , foot controlled Slammi a

polyphonic pitch-shifter/harmony pedal. The smoothly sweeps the pitch of Slammi

the guitar signal either up or down without using any moving parts, it does not use a

potentiometer, optics or magnetism. The result is a responsive pedal that allows

precise control over a clean, glitch free, polyphonic pitch-shifting algorithm. To top it

off the can create harmonized intervals by mixing your dry signal with the Slammi

effect using the adjustable DRY VOL control.

GETTING STARTED

Plug your guitar into the INPUT jack; connect your amp to the OUTPUT jack Tilt the .

Slammi forward to light the EHX logo in the center of the pedal. Your Slammi is ready

to go! as long as a plug is inserted into the P jack, a drain is Please note: IN UT

placed on the 9V battery inside the Slammi. It is recommended that you disconnect

the INPUT jack when the Slammi is not in use to extend battery life.

MAX BEND Control

The Max Bend control, located on the input side of the Slammi, acts as an 11-way

switch selecting the maximum bend or maximum interval of chromatic transposition.

The chart below shows where each maximum bend setting is located on the

thumbwheel, the odd numbers are not actually on the control:

Detune

Step

Major

2nd

Major

3rd

Perfect

4th

Perfect

5th

Major

6th

M r ino

7th

Oct

Oct/

Dive

BEND Push Button

The Bend button, next to the MAX BEND thumbwheel, selects whether the pitch is

shifted up or down relative to the original pitch. If the button is , the pitch will be out

shifted ; likewise if the button is , the pitch is shifted . UP in DOWN DRY VOL Control

The Dry Volume (DRY VOL) thumbwheel, xt to the INPUT jack, controls the volume ne

of your dry signal, mixing it with the effect signal. This enables you to harmonize with

your original pitch while at a fixed interval or when you bend notes. A detuned effect

can be made when MAX BEND is set to 0 and DRY VOL is above 0.

CALIBRATION

To ensure the Slammi responds to its full sweep range, it may be necessary to

calibrate the sweep of the Slammi when it is used on a different surface since its last

use. It is particularly important to calibrate if the Slammi is used on a slanted surface.

We recommend calibrating the Slammi after unwrapping it from its packaging, during

your first use of the pedal. Slammi is unique compared to other Next Step The

pedals in that it can be calibrated so maximum effect is either in the toe-down

position or heel-down position, allowing you to reverse the pedal sweep direction. ’s

CALIBRATION PROCEDURE TOE POSITION = MAX BEND (factory default) –

1. Place the pedal on the surface where it will be used.

2. Ensure the Slammi pedal is sitting flat on the surface then press and release

the CALIBRATE button once; the EHX logo begins to blink indicating the toe

position has been saved.

3. While the EHX logo continues to blink, rock the pedal all the way back to the

extreme heel position and hold it there.

4. Press and release the CALIBRATE button once more.

5. The EHX logo will stop blinking to indicate the heel position has been saved.

CALIBRATION PROCEDURE HEEL POSITION = MAX BEND –

1. Place the pedal on the surface where it will be used.

2. Rotate the Slammi back to the el position and hold it there while you he

press and release the CALIBRATE button once; the EHX logo begins to blink

indicating the heel position has been saved.

3. While the EHX logo blinks, tilt the pedal forward to the toe position allowing

the pedal sit flat on the surface. to

4. Press and release the CALIBRATE button once more.

5. The EHX logo will stop blinking to indicate the toe position has been saved.

If you accidentally press the CALIBRATE button and the EHX logo blinks, do not press

CALIBRATE again. After approximately 7 seconds, the Slammi will stop blinking and

ignore the button press.

Please Note: to reduce the total sweep range of the Slammi, when calibrating,

move the Slammi up a little when pressing the button to save the toe position or

move the Slammi forward a bit when pressing the button to save the heel position.

ENTERING/EXITING BYPASS

Switch between and effect mode by tipping the Slammi forward, in buffered bypass

the toe direction, past the flat position of the Slammi. You do not need to tip the

Slammi all the way forward; 25% of the total forward travel will do it. The Slammi

needs to return to its flat position before you can switch between bypass and effect

mode again.

When the Slammi is in effect mode, the EHX logo in the center of the pedal will light

up. In bypass mode, the logo does not light .

POWER

Plugging into the INPUT jack activates power from the internal 9 Volt battery. The

input cable should be removed when the unit is not in use to avoid running down the

battery. If an AC Adapter is used, the Slammi will be powered up as long as the AC

Adapter is correctly plugged in.

The Slammi’s power jack is located on the same side as the OUTPUT jack. A 9 Volt

AC Adapter capable of delivering at least 50 mA of current is required to power the

Slammi. The inner ring of the 9 Volt AC Adapter must be negative, the outer ring

positive. The optional 9V power supply from Electro-Harmonix is 9.6DC-200BI (same

as used by Boss® & Ibanez®) 9.6 Volts DC/200mA. The unit’s battery may be left in

or taken out when the AC Adapter is in use. The actual current draw of the

Slammi mA.is 24

CHANGING THE BATTERY

1. Locate the battery door at the front of the Slammi under the toe area of the ,

foot plate.

2. Remove the large black screw that holds the battery door to the case, most

coins or larger slotted screwdrivers can be used to remove this screw.

3. Connect your new 9V battery to the wired battery connector.

4. Insert the 9V battery into the battery holder clip on the battery door so that

the wired connector is on the same side of the hole in the battery door.

5. Place the battery door back into its window, in the case of the Slammi and

re-install the screw.

NOTES AND SPECIFICATIONS

• Slammi has buffered bypass.

• The input impedance presented at the INPUT Jack is 2M . The output 

impedance at the OUTPUT Jack is . 780

• The current draw of the Slammi is mA. 24

Especificaciones del producto

Marca:	Electro Harmonix
Categoría:	No categorizado
Modelo:	Next Step Slammi

¿Necesitas ayuda?

Si necesitas ayuda con Electro Harmonix Next Step Slammi haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado Electro Harmonix Manuales

Electro Harmonix Cock Fight Manual de Usario

17 Septiembre 2024

Electro Harmonix Cock Fight Plus Manual de Usario

17 Septiembre 2024

Electro Harmonix Holy Grail Max Manual de Usario

17 Septiembre 2024

Electro Harmonix The Worm Manual de Usario

16 Septiembre 2024

Electro Harmonix Canyon Echo Manual de Usario

16 Septiembre 2024

Electro Harmonix Spruce Goose Manual de Usario

15 Septiembre 2024

Electro Harmonix Germanium 4 Big Muff Pi Manual de Usario

15 Septiembre 2024

Electro Harmonix LPB-3 Manual de Usario

15 Septiembre 2024

Electro Harmonix Deluxe Memory Man 550-TT Manual de Usario

15 Septiembre 2024

Electro Harmonix Germanium OD Manual de Usario

14 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024