Electro Harmonix Superego Manual de Usario

Electro Harmonix No categorizado Superego

Lee a continuación 📖 el manual en español para Electro Harmonix Superego (2 páginas) en la categoría No categorizado. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

- WARRANTY INFORMATION -

Please register online at http://www.ehx.com/product-registration or complete and

return the enclosed warranty card within 10 days of purchase. Electro-Harmonix will

repair or replace, at its discretion, a product that fails to operate due to defects in

materials or workmanship for a period of one year from date of purchase. This

applies only to original purchasers who have bought their product from an authorized

Electro-Harmonix retailer. Repaired or replaced units will then be warranted for the

unexpired portion of the original warranty term. If you should need to return your

unit for service within the warranty period, please include a brief description of the

problem as well as you name, address, telephone number, copy of your receipt, and

a check or money order.

United States - $12

Canada - $15

Europe and outside countries - $25

Ship to:

Electro-Harmonix

C/O New Sensor Corporation

55-01 2nd Street

Long Island City, NY, 11101

Attn: Service Department

Please make checks/money orders payable to New Sensor Corporation.

To hear demos on all X pedals visit us on the web at EH www.ehx.com.

Email us at info@ehx.com

- FCC COMPLIANCE -

Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.



Consult the dealer or an experienced radio/TV technician for help .

Modifications not expressly approved by the manufacturer could void the user's authority to

operated the equipment under FCC rules.

SUPEREGO

SYNTH ENGINE

Congratulations on your purchase of the Electro-Harmonix SUPEREGO Synth

Engine; a new and unique product that combines elements of sampling, synthesis

and infinite sustain. The Superego allows the musician to freeze sound, gliss between

frozen sounds, layer sounds and place an external effects loop on only the effect. In

addition, the Superego can detect new notes or chords and sustain them

automatically without requiring the musician to step on the footswitch.

WARNING: Your Superego comes equipped with an Electro-Harmonix

9.6DC-200BI power supply (same as used by Boss® & Ibanez®: 9.6 Volts

DC 200mA). The Superego requires 140mA at 9VDC with a center negative

plug. The Superego does not take batteries. Using the wrong adapter may

damage your unit and void the warranty.

DOUBLE-TAP THE FOOTSWITCH FOR BYPASS IN LATCH OR AUTO MODE

In LATCH and AUTO modes the footswitch must be DOUBLE-TAPPED in order to

enter bypass mode. A single footswitch press in either mode will yield different

results, see the Modes section for more information.

-MODES-

The Superego has three modes: LATCH, MOMENTARY and AUTO. A toggle switch

located in the center of the Superego chooses between the three options.

MOMENTARY mode is not labeled in the artwork; it is the center (or eye) position of

the 3-position toggle switch.

MOMENTARY Mode: When the toggle switch is set to the center position, the

Superego effect is momentary, meaning the effect is only active when the footswitch

is pressed down. Upon releasing the footswitch, the Superego goes into bypass

mode. In order to properly freeze a sound, the sound must be occurring at the

moment you press down on the footswitch. Once you freeze a sound, it will sustain

for as long as you hold down the footswitch. The LED, located between the two

switches, will light while the effect is active. When you release the footswitch the LED

shuts off after the effect has fully decayed. In MOMENTARY mode, the

SPEED/LAYER knob acts as a speed control for the attack and decay time

of the effect. As you turn this knob clockwise, the speed of the effect’s fade-in and

fade-out slow down.

LATCH Mode: When the toggle switch is set to the left position, the Superego is in

LATCH mode. In this mode, press the footswitch once to activate the effect and light

the LED. After you release the footswitch the effect remains active and the sound

sustains indefinitely. In order to bypass the effect in LATCH mode you must

double-tap the footswitch, the LED will shut off to indicate bypass. To properly

freeze a sound in LATCH mode, the sound must be occurring at the moment you

press down on the footswitch. Each time you press down once on the footswitch, a

new sound is frozen.

LATCH mode also allows you to layer your notes or sounds. Each time you press

down on the footswitch to sustain a new note, the Superego will layer it on top of the

notes that were previously sustained. The SPEED/LAYER knob sets the amount of

attenuation for the old layers. If you turn this knob down to the CCW position, no

layering will occur. As you turn the SPEED/LAYER knob up, less attenuation and more

layering will occur. If you turn the knob up all the way to the maximum CW position,

each layer will remain at full volume.

AUTO Mode: Set the toggle switch to its right most position to select AUTO mode.

In the other two modes: MOMENTARY and LATCH, the Superego requires you to

press the footswitch each time you want to sustain a new note, chord or sound. In

AUTO mode the Superego detects each new note or chord that you play and sustains

it automatically. If a note not loud enough, will not trigger a new sustain is it .

When in AUTO mode, press the footswitch once to put the Superego into effect

mode, the LED will light to indicate the Superego is activated. To switch back to

bypass while in AUTO mode, you must double-tap the footswitch, after doing

so the LED shuts off. If you press and hold the footswitch while the effect is activated

and in AUTO mode, the Superego stops accepting new notes and sustains the frozen

sound indefinitely. This allows the musician to play over frozen sounds while in AUTO

mode.

As long you are not holding down the footswitch, the sustained notes automatically

fade out at a speed determined by the SPEED/LAYER knob. As you turn the knob

clockwise the fade out time increases. When the knob is set to its maximum CW

position, the sustained notes do not fade out.

-CONTROLS-

SPEED/LAYER Knob MOMENTARY: In mode, this control adjusts the speed of the

attack and decay of the frozen sound. Fully CCW produces the quickest attack and

decay, having a nearly instantaneous fade in and fade out. Fully CW yields the

longest attack and decay time for a more gradual fade in and fade out. For any given

knob setting the decay time is always longer than the attack time.

In mode, this knob is a layer control. The layer control adjusts the volume of LATCH

the previously latch-sampled sound. Turn this knob fully CCW and only the newly

latched samples will be heard. Set to fully CW, previously latched samples will not

decrease in volume and newly latched samples will be added to the existing sound.

In mode, this knob will adjust the decay of the auto triggered samples. Fully AUTO

CCW yields a very short decay time and will result in an effect that is staccato and

reverberant in nature. As you turn this knob clockwise, the decay time increases. At

fully CW, the sampled sound plays until a new sample is triggered or until the effect

is disengaged.

GLISS Knob: This control adjusts the speed of the gliss effect. Gliss morphs one

frozen note or chord into the next; it is similar to the portamento function found on

many synthesizers. As you turn the GLISS knob clockwise, the gliss effect slows

down. To turn gliss off completely, turn the GLISS knob down all the way to its full

CCW position. The easiest way to hear the GLISS effect is PERFORMANCE NOTE:

to put the Superego into AUTO mode, completely turn down the DRY knob and set

the GLI SS and SPEED knobs at 12 o’clock or higher.

D KnobRY : This knob adjusts the volume of the unaltered dry instrument signal.

Set DRY to fully CCW and no dry signal will be heard. As you turn DRY clockwise, the

volume of the dry signal will increase. Unity gain is at approximately the “2 o’clock”

setting.

EFFECT Knob: This control adjusts the volume of the wet effect signal. Fully CCW

yields no wet effect signal. As you turn the EFFECT knob clockwise the effect’s

volume increases.

Footswitch: MOMENTARYIn mode, the footswitch triggers the Superego to freeze

a new note, chord or sound when the footswitch is pressed down. The sound will be

sustained as long as the footswitch is held down. Once the footswitch is released, the

Superego goes into bypass.

In mode, the footswitch triggers the Superego to freeze a new note, chord or LATCH

sound each time it is pressed. When you release the footswitch, the Superego

continues to sustain the sound. A double-tap is required to disengage the effect.

In mode, pressing the footswitch once will engage the effect to sample new AUTO

notes, chords and sounds automatically. If the footswitch is held down while the

effect is ON, the Superego stops accepting new notes while sustaining the last sound

that was sampled, enabling the musician to play over the frozen sound. A double-tap

of the footswitch is required to disengage the effect.

TOGGLE Switch: The toggle switch selects the mode of operation for the Superego.

Point the switch to the left and Superego is in mode Set the toggle to the LATCH .

center position for mode, MOMENTARY . Set the switch to the right for mode. AUTO

INPUT Jack: Connect the output of your guitar into the INPUT jack of the Superego.

The input impedance presented at the INPUT jack is 2.2Mohms.

OUTPUT Jack: Connect the OUTPUT jack of the Superego into the input of your

amplifier, or another effects pedal. The output impedance is approximately 200

ohms.

SEND Jack and RETURN Jack: The SEND and RETURN jacks help to form an

effects loop for patching additional effects that will process the wet signal only. in

SEND is an output with impedance < 5k ohms. RETURN is an put with impedance = in

2.2M. To properly connect an external effects loop, connect the SEND jack to the

input of the first effect in the effects loop. Connect the output of the last effect in the

loop to the RETURN jack. While in Bypass, the SEND jack is muted.

The jSEND ack can also be used independently as a “wet out”. To use the SEND

jack as a “wet out”, connect the send jack to another amplifier, or effects chain, and

leave the RETURN jack disconnected .

9V PWR Jack: Connect the output plug of the supplied AC Adaptor into the 9V

power jack at the top of Superego. The Superego 0mA at ’s current requirement is 14

9VDC. The polarity of the power jack is center negative. The maximum allowable

power supply voltage is 10.5 VDC.

Especificaciones del producto

Marca:	Electro Harmonix
Categoría:	No categorizado
Modelo:	Superego
Fuente de alimentación:	24 - 34 V DC
Resolución Máxima:	1280 x 720 Pixels
Tipo de fuente de energía:	Power over Ethernet (PoE)
Iluminación mínima:	0.74 Lux
Micrófono, entrada de línea:	Ja
Número de puertos Ethernet LAN (RJ-45):	1
Tamaño del sensor óptico:	1/3 "
Conexión para adaptador de red:	Ja
Tipo de sensor de imagen:	CCD
Micrófono incorporado:	Ja
Máximo 30 cuadros por segundo:	25 fps
Funciones de red:	IEEE 802.3a
Alimentación a través de Ethernet (PoE):	Ja
rango de panorámica:	0 - 360 °
Rango de ángulo de inclinación:	0 - 180 °
Detección de audio:	Ja