Entes DTR-10t Manual de Usario

Lee a continuación 📖 el manual en español para Entes DTR-10t (36 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/36
www.entes.eu
DTR-10t User Manual and
Menu Map
Adr: Dudullu OSB; 1. Cadde; No:23 34776 Ümraniye - İSTANBUL / TÜRKİYE
Tel: Fax: E-mail: Web: +90 216 313 01 10 +90 216 314 16 15 contact@entes.eu www.entes.eu
Call Center Technical Support: 0850 888 84 25 A5320/Rev.5
1 2
DTR-10t, which has a real time clock, is an electronic timer that calculates the sunset and sunrise periods au-
tomatically. It is designed for controlling the devices which are connected to its contacts according to sunset,
sunrise and the time periods which are programmed by the user.
ESC Button : It is used to switch between monitoring menus. In the programming mode, it is used to cancel
a parameter change or to return to the previous menu.
SET Button : It is used to switch between monitoring menus. When it is pressed for 3 seconds, programming
YUKARI mode is entered. In the programming mode, it is used to apply a parameter change or to enter
to a menu.
DOWN Buttons :
In the monitoring menu, it is used to switch between programs to show their activity in a
day.
When the DOWN button is pressed for 3 seconds, C1 relay goes into manual mode. In
the programming
menu; it is used to browse between menus, to select parameters and to
adjust values with digits.
Precautions for Installation and Safe Use
If below precautions are not properly observed and carried out, it may result in cases with injury or death. -
Disconnect power before working on the device.
- When device is connected to the network, do not remove the front panel.
- Do not clean the device with solvent or similar items. Only clean with dry cloth.
- Verify correct terminal connections before energizing the device.
- Install the device on the electrical panel.
- Contact your authorized reseller in case problems occur with your device.
No responsibility is assured by the manufacturer or any of its subsidiaries for any consequences rising
out of the use of this material.
- The output loads connected to the relays do not function if auxiliary supply is absent. Even if the relay status
is monitored as on”( ), auxiliary supply is a must for the operation.
- There are two reserves in the device. Programmed data is protected by these reserves against power outages.
- For long time reserve, a battery is used. If the device is not continously supplied with voltage and waited on the shelf,
the battery life is 5 years.
- Reserve battery should only be changed by the authorized service.
MANUAL MODE :
In order to use the relay outputs manually, DTR-10t has to be in the monitoring mode. The DOWN button is used to
switch the C1 relay to manual mode. When the UP or DOWN button is pressed for 3 seconds, “MANUAL indication
appears on the screen. If this is done while the relay C1 is activated, that relay will be deactivated. If it is done while
the relay C1 is deactivated, no switching will occur. When the device is in manual mode and the relay is not energized,
and the DOWN button is pressed once C1 contact will turn o its contact at the end of a 3-second delay. During this
delay, the symbol indicating the state of the relay contact is ashing. After the activation of the contact, when the
DOWN button is pressed again for 3 sec, C1 relay will exit the manual mode. The relay will stay activated or deactivated
according to the program ow. When both of the the relays are in manual mode, “AUTO” indication will dissappear
from the screen.

Especificaciones del producto

Marca: Entes
Categoría: No categorizado
Modelo: DTR-10t

¿Necesitas ayuda?

Si necesitas ayuda con Entes DTR-10t haz una pregunta a continuación y otros usuarios te responderán




No categorizado Entes Manuales

No categorizado Manuales

Últimos No categorizado Manuales