Extron USB Plus Matrix Controller Manual de Usario

Extron No categorizado USB Plus Matrix Controller

Lee a continuación 📖 el manual en español para Extron USB Plus Matrix Controller (12 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/12
1
USB Plus Matrix Controller • Setup Guide
The Extron® USB Plus Matrix Controller is a pre-congured controller that can easily be setup and deployed to control Extron
USBExtenderPlus products in a USB Matrix switching application within a gigabit Ethernet network. Quick and easy setup of
the USBPlusMatrixController, USB Extender Plus transmitters and receivers is done using Extron Product Conguration Soft-
ware (PCS). An Extron Control System or any third party control can interface with the USB Plus Matrix Controller via Ethernet or
RS-232 to perform USB switching.
The main components in a USB Extender Plus Matrix system:
• USB Plus Matrix Controller — The controller is pre-congured to control the USB Extender Plus transmitters and receivers
in a USB Matrix switching application. The default Telnet port is 22123 (see the for full USB Plus Matrix Controller Help File
details).
• USB Plus Extenders (transmitters and receivers) — At least 1 transmitter and 1 receiver are required, and up to 64
extenders total may be included. Each extender must be assigned a unique IP address (DHCP cannot be used to assign
these addresses), and these addresses are uploaded to the USB Plus Matrix Controller. All twisted pair models are supported:
rack mountable models (standard and HID-only), AAP™ models, and decorator-style models (see the USB Extender Plus
Series User Guide, available on www.extron.com, for more information about these models).
• Product Configuration Software (PCS) — This free software is loaded on the computer and is used to congure the
USB Extender Plus transmitters and receivers. It is also used to create a conguration that is uploaded to the USB Matrix
Controller (see the for details on how to use PCS with the USB Matrix Controller).USB Plus Matrix Controller Help File
• Extron Toolbelt — This free software is used to congure the IP settings of the USB Matrix Controller (see the Toolbelt Help
File at www.extron.com for details on how to use Toolbelt).
Installation
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
• Do not perform a Mode 5 reset (see to the USB Matrix Controller. Doing so will USB Plus Matrix Controller Help File)
erase the factory loaded conguration used to control the USB Extender Plus transmitters and receivers.
• N’effectuez aucune réinitialisation complète de système (mode 5) (voir sur l’USB USB Plus Matrix Controller Help File)
Matrix Controller. Cette action entraînera en effet la suppression de la conguration par défaut, utilisée pour le contrôle
des émetteurs et récepteurs USBExtenderPlus.
The following diagram shows an example of a USB Plus Matrix Controller system setup:
USB EXTENDER Plus R
CONF IG
PAIR
ST USAT
LIN K
HOS T
1
3
2
4
Rx 1
USB EXTENDER Plus R
CONF IG
PAIR
ST USAT
LIN K
HOS T
1
3
2
4
Rx 2
USB EXTENDER Plus R
CONF IG
PAIR
ST USAT
LIN K
HOS T
1
3
2
4
Rx 3
USB EXTENDER Plus R
CONF IG
PAIR
ST USAT
LIN K
HOS T
1
3
2
4
Rx 4
LAN
Tx
1
USB EXTENDER Plus T
S USTAT
LIN K
HOS T
CONF IG
PAIR
Tx
2
USB EXTENDER Plus T
S USTAT
LIN K
HOS T
CONF IG
PAIR
Tx
3
USB EXTENDER Plus T
S USTAT
LIN K
HOS T
CONF IG
PAIR
Tx
4
USB EXTENDER Plus T
S USTAT
LIN K
HOS T
CONF IG
PAIR
USB Matrix Controller
Control System
SIS (Simple I n t C )nstructio Se ommands
a
t
COM
RT S
CT S
T x
Rx
R
USB PL US MATRI X
C
C
o
t
n
t
ro
l
l
S
S
y
t
s
t
em
r
t
rix
C
ontrolle
r
S
I
S
(S
im
p
le sIn
t
Control
Figure 1. Application Diagram of the USB Plus Matrix Controller System
USB Plus Matrix Controller • Setup Guide (Continued)
2
General Setup for the USB Extender Matrix System
1. Enable the Network Pairing feature on each USB Extender transmitter and receiver to be used in the USB Matrix system.
2. Use Extron Toolbelt to congure the IP settings of the USB Matrix Controller (IP, Subnet, and Gateway addresses).
NOTE: USB Extender Transmitters and Receivers must be on a static IP. Do not configure the extenders for DHCP
mode.
3. Use PCS software and the included 9-pin to 2.5 mm TRS serial cable to sequentially congure each of the IP settings of the
USB Extenders via the Cong port of the product and create a USB Matrix Conguration.
4. Use PCS software to upload the conguration of the USB matrix setup to the USB Plus Matrix controller.
5. Set up an (Extron) control system to control the matrix switching by making input and output ties. Use an Extron IPL control
driver, available on the .Extron website
Setup Requirements
The following are required for the USB Plus Matrix system setup:
• Download Toolbelt and PCS from the Extron website —
• The computer running Toolbelt and PCS to congure the USB Matrix must be on the same Subnet and Gateway.
• USB Extenders Plus (applies to all extenders in the system) —
• Must have a IP address (see the ).unique USB Plus Matrix Controller Help File
NOTE: USB Extender Transmitters and Receivers must be on a static IP. Do not configure the extenders for DHCP
mode.
• Over network pairing must be enabled (see the ).USB Extender Plus T/R User Guide
• Must be on the as the controller and all other USB extenders in the system.same subnet and gateway
• Must have the as all other USB Extender Plus in the system.same firmware
• USB Plus Matrix Controller —
• Must use Extron Toolbelt to congure the IP, Subnet and Gateway address.
• Must be on the same subnet and gateway as the extenders.
• Must have an admin password assigned.
• Control System —
• An Extron or third party control system is required to interface and control the USB Matrix Controller to make and break
ties between the USB Extender Plus transmitters and receivers.
• USB Plus Matrix Controller driver is available on the Extron website.
Hardware Setup
To connect the devices:
1. Connect the USB Plus Matrix Controller to the network via the LAN (TCP) RJ-45 port (see gure2,
2).
POWER
12V
0.2A MAX
GTx Rx
RTS CTS
C O M
USB PLUS MATRIX
LAN / PoE
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
2222
1111
Figure 2. USB Plus Matrix Controller Rear Panel
2. Connect power to the USB Plus Matrix Controller (see gure2, 1) and to the rst USB extender that you will be conguring.
CAUTION: The wires must be kept separate while the power supply is plugged in. Remove power before wiring.
ATTENTION : Les deux cordons d’alimentation doivent être maintenus séparés lorsque la source d’alimentation est
branchée. Coupez l’alimentation avant d’effectuer un raccordement.
ATTENTION:
Do not connect power to the switcher until you have read the ATTENTION notices on page12.
Ne branchez pas l’alimentation au sélecteur avant d’avoir lu les mises en garde ATTENTION aux page12.
3. Connect one of the USB transmitters and receivers to the computer via the Cong port (see gure3,
1) using the included
9-pin to 2.5 mm TRS serial cable.
NOTE: Figure 3 shows the transmitter models only. However, on each receiver the Config port is at the same location as
on the equivalent transmitter model.
PO
WER
--
A MAX
CO
NFI
G
U
S
B EXTENDER PLU
S
D T
POWER
12V
--A MAX
PAIR
CONFIG
USB EXTENDER PLUS D T
11
POWER
12V
--A MAX
PAIR
HOST LINK
CONFIG
11
11
USB Extender Plus T/R (Rack-mountable), Fr
ont Panel
USB Extender Plus T/R AAP, Rear Panel
USB Extender Plus T/R D
(Decorator-Style llplate),Wa
Rear Panel
USB EXTENDER Plus T
S TUSTA
LINK
HOST
CONFIG
PAIR
Figure 3. Config Port Locations on the Three USB Extender Plus Models
Software Setup
PCS and Toolbelt are available free of charge from the . Use PCS software to congure the USB extenders and Extron website
upload their IP addresses to the USB Plus Matrix Controller controller. Use Extron Toolbelt to congure the IP settings of the USB
Matrix Controller (see the for details).USB Plus Matrix Controller Help File
Dowloading the software
To obtain PCS and Toolbelt from the Extron website:
1. Go to www.extron.com. On the main page, click the tab (see gure4, 1).
Figure 4. Download Page on Extron Website
2. To download PCS, click (2) in the left panel of the screen.
3

Especificaciones del producto

Marca: Extron
Categoría: No categorizado
Modelo: USB Plus Matrix Controller

¿Necesitas ayuda?

Si necesitas ayuda con Extron USB Plus Matrix Controller haz una pregunta a continuación y otros usuarios te responderán


No categorizado Extron Manuales

Extron

Extron PI 115 Manual de Usario

27 Octubre 2024
Extron

Extron XTP DTP 24 Manual de Usario

27 Octubre 2024
Extron

Extron IN1608 XI Manual de Usario

25 Octubre 2024
Extron

Extron FOX II RS 104 Manual de Usario

25 Octubre 2024
Extron

Extron DTP T UWP 4K 232 D Manual de Usario

1 Octubre 2024
Extron

Extron FOX Matrix 7200 Manual de Usario

24 Septiembre 2024
Extron

Extron EWB 210 Series Manual de Usario

24 Septiembre 2024
Extron

Extron EDID 101D Manual de Usario

24 Septiembre 2024
Extron

Extron FMR 206 Manual de Usario

24 Septiembre 2024
Extron

Extron EWB Series Manual de Usario

24 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024