Fenix LD12 Manual de Usario

Fenix Flash LD12

Lee a continuación 📖 el manual en español para Fenix LD12 (3 páginas) en la categoría Flash. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/3
Fenix LD12
Fenix LD12 is a widely used multifunctional flashlight. Offering 4 brightness levels and 2
different flashing functions, it can operate simply via the side mode switch. It makes a perfect
combination between different needs in brightness and runtime in various conditions. Featuring
the universal AA battery, compact and exquisite design, advanced constant brightness technology
and waterproofing to IPX- r8 Standard, LD12 must be you good to meet the needs in partner
various outdoor conditions and in the urgent condition.
Technical Parameters
General Mode
ANSI/FSC
Turbo
Low
Mid
High
Strobe
SOS
OUTPUT
115
LUMENS
3
LUMENS
27
LUMENS
60
LUMENS
115
LUMENS
60
LUMENS
RUNTIME
2h 9 min
97h
11h
4h 51 min
DISTANCE
80m
INTENSITY
1612cd
IMPACT
RESISTANT
1m
WATERPROOF
IPX-8 2m underwater
EXTRA
FUNCTIONS
ACCESSORIES
Holster, body clip, lanyard - and spare o ring
Cree XP-G (R5) LED with a lifespan of 50,000 hours
Uses one 1.5V AA (Ni-MH, Alkaline ) battery
105mm (Length) x 21.5mm (Diameter)
54-gram weight (excluding battery and holster)
Digitally regulated output - maintains constant brightness
Reverse polarity protection, to protect from improper battery installation
- - Anti roll, slip resistant body design
Tactical tail cap switch with momentary-on function
Side mode switch in the front
Made of durable aircraft- grade aluminum
Premium Type III hard- - anodized anti abrasive finish
Toughened ultra-clear glass lens with anti coating-reflective
Notice: The above-mentioned parameters (tested by 2500mAh batteryNi-MH in Lab) are
approximate and may vary between flashlights, batteries and environments.
Operation Instruction
The tail cap switch is the power switch and the side button is the mode switch.
Press the tail cap switch lightly to activate the flashlight momentarily (without any press, it will be
off); Press the tail cap switch completely to turn on the flashlight and lock it. Another press can
turn it off.
When the flashlight is on, a single press on the side mode switch can select the brightness levels in
the order of Turbo Low Mid High Cycle;
Press and hold the side mode switch for about one second to enter into the Strobe. It will flash in
the frequency of 6Hz/15Hz and transfer the frequency in every 2 seconds.
Press and hold the side mode switch for about 3 seconds to enter into the SOS.
Under the condition of Strobe or SOS, a single press on the side mode switch can return to the
general mode.
The flashlight can memorize the brightness levels in the general mode except the mode. When
turn it on, it will begin to work in the general mode.
Battery Specifications
Dimensions
Nominal voltage
Usability
AA
1.2V
Recommended
AA
1.5V
Usable
AA
1.5V
Usable
14500
3.7V
Banned
×
Battery Replacement
Unscrew the tail cap to put in the battery with the anode side (+) toward the light head, screw the
tail cap back on to test.
Usage and Maintenance
Please don't disassemble the sealed head, doing so can cause damage to the flashlight and will
void the warranty.
High-power light should use battery with high current discharge ability, we suggest using high
performance Ni-MH rechargeable battery, using alkaline battery will lower the runtime of
high- intensity light.
Please use batteries of high quality, if the flashlight is not to be used for an extended period ,
remove the battery, or the flashlight could be damaged by electrolyte leakage or battery explosion.
Due to the momentary-on tactical switch, perhaps the flashlight will activate unconsciously.
To avoid this case, please unscrew the tail cap for half a turn before put it into the bag.
-The O ring may be worn out after using for a long time. If it happens, please replace the
O- ring with a new one to keep the flashlight properly sealed against water.
Please clean the contacts of your light from time to time, especially if the light flickers or
doesn't light up. There may be several reasons for a flickering or not working light:
Reason A: The battery needs replacing.
Solution: Replace batteries (Please confirm the correct installation of anode and cathode).
Reason B: The threads, PCB board contact or other contacts are dirty.
Solution: Clean the contact points with an alcohol soaked cotton swab.
If the above methods don't work, please contact the distributors and refer to the warranty policy.
Product Warranty
We will replace products afflicted with manufacturing defects within 15 days of purchase and
repair a light free of charge within 24 months of purchase if problems develop with normal use; if
repair is required after 24 months from the date of purchase, we will charge for parts. The total
repair fee is dictated by the cost of the replaced materials.
Warranty Card Registration
We kindly suggest that you register your guarantee card on the official website of Fenixlight
Limited. You can get an extra six-month warranty period once you have successfully registered.
What's more, you could take part in the lottery of questionnaire at the same time.
Warning
LD12 is a high-intensity lighting device and capable the of causing eye damage, avoid shining
light directly into the eyes.

Especificaciones del producto

Marca: Fenix
Categoría: Flash
Modelo: LD12

¿Necesitas ayuda?

Si necesitas ayuda con Fenix LD12 haz una pregunta a continuación y otros usuarios te responderán




Flash Fenix Manuales

Fenix

Fenix E35R Manual de Usario

16 Septiembre 2024
Fenix

Fenix BC25R Manual de Usario

14 Septiembre 2024
Fenix

Fenix HT32 Manual de Usario

12 Septiembre 2024
Fenix

Fenix TK75 Manual de Usario

10 Septiembre 2024
Fenix

Fenix TK32 Manual de Usario

10 Septiembre 2024
Fenix

Fenix HT30R Manual de Usario

10 Septiembre 2024
Fenix

Fenix E15 Manual de Usario

10 Septiembre 2024

Flash Manuales

Últimos Flash Manuales