Festo EAHM-E15-80-E22 Manual de Usario

Festo No categorizado EAHM-E15-80-E22

Lee a continuación 📖 el manual en español para Festo EAHM-E15-80-E22 (1 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/1
EAHM-E15-...-E22
Mounting kit
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Assembly instructions
8156951
2021-07
[8156953]
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
è www.festo.com/sp.
Document Product Table of contents
Operating instructions Handling system YXCA/YXCF/
YXCR
Assembly
Tab. 1: Applicable documents
2 Safety
2.1 Safety instructions
Before working on the product, switch off the power supply and secure it
against being switched on again.
Observe further applicable documents.
Observe tightening torques.
2.2 Intended use
Mounting the X-axes ELGC or a handling system YXCA/YXCF/YXCR.
3 Additional information
Accessories of the handling system YXCA/YXCF/YXCR
è
www.festo.com/cata-
logue
4 Product Range Overview
4.1 Scope of delivery
1
2
3
Fig.1
1
Mounting flange (1x)
2
Screw (8x)
M5x12
3
Profile mounting (2x)
4.2 Not in scope of delivery
4
Fig.2
4
X-module (1x)
EHMX-...-ELGC
5 Assembly
Fig.3
Observe the number of mounting kits and the support spacings X2 (
è 1
Applicable documents).
Centring pins facilitate subsequent replacement of the actuator.
The hole [A] is intended for optional centring of a profile mounting with a3
centring pin.
2
1A
Fig.4
EAHM-E15-...-E22 60 80
X3 [mm] 68 68
Y2 [mm] 80 100
Tab. 2: Hole spacing
Fasten the mounting flange to the mounting surface with four screws .1 2
Tightening torque: 6 Nm ± 20%
3B
C
Fig.5
1. Align the X-axes precisely together (
è 1 Applicable documents).
2. Push the lugs [C] of the profile mountings into the profile slots [B].3
2
3
D
A
Fig.6
EAHM-E15-...-E22 60 80
Drilled hole [A] for centring
pin [D]
[mm] 5 H8Æ
Tab. 3: Drilled hole for centring pin
1. Optionally fasten the profile mounting with centring pin [D] to the3
mounting flange .1
2. Fasten both profile mountings with the screws to the mounting3 2
flange . Tightening torque: 4.8 Nm ± 20% 1

Especificaciones del producto

Marca: Festo
Categoría: No categorizado
Modelo: EAHM-E15-80-E22

¿Necesitas ayuda?

Si necesitas ayuda con Festo EAHM-E15-80-E22 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Festo Manuales

No categorizado Manuales

Últimos No categorizado Manuales